kernel/linux.git/drivers/usb/host, branch v5.4.151

xhci: Set HCD flag to defer primary roothub registration

2021-09-30T08:09:22+00:00

commit b7a0a792f864583207c593b50fd1b752ed89f4c1 upstream. Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer registering primary roothub in usb_add_hcd(). This will make sure both primary roothub and secondary roothub will be registered along with the second HCD. This is required for cold plugged USB devices to be detected in certain PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM). CC: stable@vger.kernel.org # 5.4+ Suggested-by: Mathias Nyman Tested-by: Chris Chiu Signed-off-by: Kishon Vijay Abraham I Link: https://lore.kernel.org/r/20210909064200.16216-3-kishon@ti.com Signed-off-by: Greg Kroah-Hartman

Revert "USB: xhci: fix U1/U2 handling for hardware with XHCI_INTEL_HOST quirk set"

2021-09-22T10:26:35+00:00

[ Upstream commit 2847c46c61486fd8bca9136a6e27177212e78c69 ] This reverts commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760. That commit effectively disabled Intel host initiated U1/U2 lpm for devices with periodic endpoints. Before that commit we disabled host initiated U1/U2 lpm if the exit latency was larger than any periodic endpoint service interval, this is according to xhci spec xhci 1.1 specification section 4.23.5.2 After that commit we incorrectly checked that service interval was smaller than U1/U2 inactivity timeout. This is not relevant, and can't happen for Intel hosts as previously set U1/U2 timeout = 105% * service interval. Patch claimed it solved cases where devices can't be enumerated because of bandwidth issues. This might be true but it's a side effect of accidentally turning off lpm. exit latency calculations have been revised since then Signed-off-by: Mathias Nyman Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

USB: EHCI: ehci-mv: improve error handling in mv_ehci_enable()

2021-09-22T10:26:28+00:00

[ Upstream commit 61136a12cbed234374ec6f588af57c580b20b772 ] mv_ehci_enable() did not disable and unprepare clocks in case of failures of phy_init(). Besides, it did not take into account failures of ehci_clock_enable() (in effect, failures of clk_prepare_enable()). The patch fixes both issues and gets rid of redundant wrappers around clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit. Found by Linux Driver Verification project (linuxtesting.org). Acked-by: Alan Stern Signed-off-by: Evgeny Novikov Link: https://lore.kernel.org/r/20210708083056.21543-1-novikov@ispras.ru Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: host: fotg210: fix the actual_length of an iso packet

2021-09-22T10:26:28+00:00

[ Upstream commit 091cb2f782f32ab68c6f5f326d7868683d3d4875 ] We should acquire the actual_length of an iso packet from the iTD directly using FOTG210_ITD_LENGTH() macro. Signed-off-by: Kelly Devilliv Link: https://lore.kernel.org/r/20210627125747.127646-4-kelly.devilliv@gmail.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: host: fotg210: fix the endpoint's transactional opportunities calculation

2021-09-22T10:26:28+00:00

[ Upstream commit c2e898764245c852bc8ee4857613ba4f3a6d761d ] Now that usb_endpoint_maxp() only returns the lowest 11 bits from wMaxPacketSize, we should make use of the usb_endpoint_* helpers instead and remove the unnecessary max_packet()/hb_mult() macro. Signed-off-by: Kelly Devilliv Link: https://lore.kernel.org/r/20210627125747.127646-3-kelly.devilliv@gmail.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: ehci-orion: Handle errors of clk_prepare_enable() in probe

2021-09-15T07:47:36+00:00

[ Upstream commit 4720f1bf4ee4a784d9ece05420ba33c9222a3004 ] ehci_orion_drv_probe() did not account for possible errors of clk_prepare_enable() that in particular could cause invocation of clk_disable_unprepare() on clocks that were not prepared/enabled yet, e.g. in remove or on handling errors of usb_add_hcd() in probe. Though, there were several patches fixing different issues with clocks in this driver, they did not solve this problem. Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe() to avoid calls of clk_disable_unprepare() without previous successful invocation of clk_prepare_enable(). Found by Linux Driver Verification project (linuxtesting.org). Fixes: 8c869edaee07 ("ARM: Orion: EHCI: Add support for enabling clocks") Co-developed-by: Kirill Shilimanov Reviewed-by: Andrew Lunn Acked-by: Alan Stern Signed-off-by: Evgeny Novikov Signed-off-by: Kirill Shilimanov Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: host: ohci-tmio: add IRQ check

2021-09-15T07:47:35+00:00

[ Upstream commit 4ac5132e8a4300637a2da8f5d6bc7650db735b8a ] The driver neglects to check the result of platform_get_irq()'s call and blithely passes the negative error codes to usb_add_hcd() (which takes *unsigned* IRQ #), causing request_irq() that it calls to fail with -EINVAL, overriding an original error code. Stop calling usb_add_hcd() with the invalid IRQ #s. Fixes: 78c73414f4f6 ("USB: ohci: add support for tmio-ohci cell") Acked-by: Alan Stern Signed-off-by: Sergey Shtylyov Link: https://lore.kernel.org/r/402e1a45-a0a4-0e08-566a-7ca1331506b1@omp.ru Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

xhci: fix unsafe memory usage in xhci tracing

2021-09-12T06:56:41+00:00

commit cbf286e8ef8337308c259ff5b9ce2e74d403be5a upstream. Removes static char buffer usage in the following decode functions: xhci_decode_trb() xhci_decode_ptortsc() Caller must provide a buffer to use. In tracing use __get_str() as recommended to pass buffer. Minor chanes are needed in xhci debugfs code as these functions are also used there. Changes include moving XHCI_MSG_MAX definititon from xhci-trace.h to xhci.h Cc: Signed-off-by: Mathias Nyman Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman

usb: host: xhci-rcar: Don't reload firmware after the completion

2021-09-12T06:56:41+00:00

commit 57f3ffdc11143f56f1314972fe86fe17a0dcde85 upstream. According to the datasheet, "Upon the completion of FW Download, there is no need to write or reload FW.". Otherwise, it's possible to cause unexpected behaviors. So, adds such a condition. Fixes: 4ac8918f3a73 ("usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers") Cc: stable@vger.kernel.org # v3.17+ Signed-off-by: Yoshihiro Shimoda Link: https://lore.kernel.org/r/20210827063227.81990-1-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman

USB:ehci:fix Kunpeng920 ehci hardware problem

2021-08-15T11:08:04+00:00

commit 26b75952ca0b8b4b3050adb9582c8e2f44d49687 upstream. Kunpeng920's EHCI controller does not have SBRN register. Reading the SBRN register when the controller driver is initialized will get 0. When rebooting the EHCI driver, ehci_shutdown() will be called. if the sbrn flag is 0, ehci_shutdown() will return directly. The sbrn flag being 0 will cause the EHCI interrupt signal to not be turned off after reboot. this interrupt that is not closed will cause an exception to the device sharing the interrupt. Therefore, the EHCI controller of Kunpeng920 needs to skip the read operation of the SBRN register. Acked-by: Alan Stern Signed-off-by: Longfang Liu Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com Signed-off-by: Greg Kroah-Hartman