kernel/linux.git/drivers/usb/dwc2, branch v4.4.171

usb: gadget: dwc2: fix memory leak in gadget_init()

2018-08-24T11:26:54+00:00

[ Upstream commit 9bb073a053f0464ea74a4d4c331fdb7da58568d6 ] Freed allocated request for ep0 to prevent memory leak in case when dwc2_driver_probe() failed. Cc: Stefan Wahren Cc: Marek Szyprowski Tested-by: Stefan Wahren Tested-by: Marek Szyprowski Acked-by: Minas Harutyunyan Signed-off-by: Grigor Tovmasyan Signed-off-by: Felipe Balbi Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: dwc2: fix isoc split in transfer with no data

2018-08-24T11:26:54+00:00

[ Upstream commit 70c3c8cb83856758025c2a211dd022bc0478922a ] If isoc split in transfer with no data (the length of DATA0 packet is zero), we can't simply return immediately. Because the DATA0 can be the first transaction or the second transaction for the isoc split in transaction. If the DATA0 packet with no data is in the first transaction, we can return immediately. But if the DATA0 packet with no data is in the second transaction of isoc split in transaction sequence, we need to increase the qtd->isoc_frame_index and giveback urb to device driver if needed, otherwise, the MDATA packet will be lost. A typical test case is that connect the dwc2 controller with an usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics headset) into the downstream port of Hub. Then use the usb mic to record, we can find noise when playback. In the case, the isoc split in transaction sequence like this: - SSPLIT IN transaction - CSPLIT IN transaction - MDATA packet (176 bytes) - CSPLIT IN transaction - DATA0 packet (0 byte) This patch use both the length of DATA0 and qtd->isoc_split_offset to check if the DATA0 is in the second transaction. Tested-by: Gevorg Sahakyan Tested-by: Heiko Stuebner Acked-by: Minas Harutyunyan hminas@synopsys.com> Signed-off-by: William Wu Signed-off-by: Felipe Balbi Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Fix interval type issue

2018-05-30T05:49:12+00:00

[ Upstream commit 12814a3f8f9b247531d7863170cc82b3fe4218fd ] The maximum value that unsigned char can hold is 255, meanwhile the maximum value of interval is 2^(bIntervalMax-1)=2^15. Signed-off-by: Grigor Tovmasyan Signed-off-by: Felipe Balbi Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Fix dwc2_hsotg_core_init_disconnected()

2018-05-30T05:48:58+00:00

[ Upstream commit 755d739534f998d92e348fba8ffb0478416576e7 ] We should call dwc2_hsotg_enqueue_setup() after properly setting lx_state. Because it may cause error-out from dwc2_hsotg_enqueue_setup() due to wrong value in lx_state. Issue can be reproduced by loading driver while connected A-Connector (start in A-HOST mode) then disconnect A-Connector to switch to B-DEVICE. Acked-by: John Youn Signed-off-by: Vardan Mikayelyan Signed-off-by: Grigor Tovmasyan Signed-off-by: Felipe Balbi Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Improve gadget state disconnection handling

2018-04-08T09:51:59+00:00

commit d2471d4a24dfbff5e463d382e2c6fec7d7e25a09 upstream. In the earlier commit dad3f793f20f ("usb: dwc2: Make sure we disconnect the gadget state"), I was trying to fix up the fact that we somehow weren't disconnecting the gadget state, so that when the OTG port was plugged in the second time we would get warnings about the state tracking being wrong. (This seems to be due to a quirk of the HiKey board where we do not ever get any otg interrupts, particularly the session end detected signal. Instead we only see status change interrupt.) The fix there was somewhat simple, as it just made sure to call dwc2_hsotg_disconnect() before we connected things up in OTG mode, ensuring the state handling didn't throw errors. But in looking at a different issue I was seeing with UDC state handling, I realized that it would be much better to call dwc2_hsotg_disconnect when we get the state change signal moving to host mode. Thus, this patch removes the earlier disconnect call I added and moves it (and the needed locking) to the host mode transition. Cc: Wei Xu Cc: Guodong Xu Cc: Amit Pundir Cc: YongQin Liu Cc: John Youn Cc: Minas Harutyunyan Cc: Douglas Anderson Cc: Chen Yu Cc: Felipe Balbi Cc: Greg Kroah-Hartman Cc: linux-usb@vger.kernel.org Acked-by: Minas Harutyunyan Tested-by: Minas Harutyunyan Signed-off-by: John Stultz Signed-off-by: Felipe Balbi Cc: Ben Hutchings Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Make sure we disconnect the gadget state

2018-03-22T08:23:26+00:00

[ Upstream commit dad3f793f20fbb5c0c342f0f5a0bdf69a4d76089 ] I had seen some odd behavior with HiKey's usb-gadget interface that I finally seemed to have chased down. Basically every other time I plugged in the OTG port, the gadget interface would properly initialize. The other times, I'd get a big WARN_ON in dwc2_hsotg_init_fifo() about the fifo_map not being clear. Ends up if we don't disconnect the gadget state, the fifo-map doesn't get cleared properly, which causes WARN_ON messages and also results in the device not properly being setup as a gadget every other time the OTG port is connected. So this patch adds a call to dwc2_hsotg_disconnect() in the reset path so the state is properly cleared. With it, the gadget interface initializes properly on every plug in. Cc: Wei Xu Cc: Guodong Xu Cc: Amit Pundir Cc: Rob Herring Cc: John Youn Cc: Douglas Anderson Cc: Chen Yu Cc: Felipe Balbi Cc: Greg Kroah-Hartman Cc: linux-usb@vger.kernel.org Acked-by: John Youn Signed-off-by: John Stultz Signed-off-by: Felipe Balbi Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

usb: dwc2: fix regression on big-endian PowerPC/ARM systems

2016-07-27T16:47:28+00:00

commit 23e3439296a55affce3ef0ab78f1c2e03aec8767 upstream. A patch that went into Linux-4.4 to fix big-endian mode on a Lantiq MIPS system unfortunately broke big-endian operation on PowerPC APM82181 as reported by Christian Lamparter, and likely other systems. It actually introduced multiple issues: - it broke big-endian ARM kernels: any machine that was working correctly with a little-endian kernel is no longer using byteswaps on big-endian kernels, which clearly breaks them. - On PowerPC the same thing must be true: if it was working before, using big-endian kernels is now broken. Unlike ARM, 32-bit PowerPC usually uses big-endian kernels, so they are likely all broken. - The barrier for dwc2_writel is on the wrong side of the __raw_writel(), so the MMIO no longer synchronizes with DMA operations. - On architectures that require specific CPU instructions for MMIO access, using the __raw_ variant may turn this into a pointer dereference that does not have the same effect as the readl/writel. This patch is a simple revert for all architectures other than MIPS, in the hope that we can more easily backport it to fix the regression on PowerPC and ARM systems without breaking the Lantiq system again. We should follow this up with a more elaborate change to add runtime detection of endianness, to make sure it also works on all other combinations of architectures and implementations of the usb-dwc2 device. That patch however will be fairly large and not appropriate for backports to stable kernels. Felipe suggested a different approach, using an endianness switching register to always put the device into LE mode, but unfortunately the dwc2 hardware does not provide a generic way to do that. Also, I see no practical way of addressing the problem more generally by patching architecture specific code on MIPS. Fixes: 95c8bc360944 ("usb: dwc2: Use platform endianness when accessing registers") Acked-by: John Youn Tested-by: Christian Lamparter Signed-off-by: Arnd Bergmann Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

usb: dwc2: fix kernel oops during driver probe

2015-11-20T15:29:47+00:00

This patch make sure that all necessary members of dwc2_hsotg are initialized before the irq handler is requested. So the kernel oops triggered by dwc2_handle_common_intr has been fixed. dwc2 20980000.usb: Configuration mismatch. Forcing host mode dwc2 20980000.usb: no platform data or transceiver defined Unable to handle kernel paging request at virtual address cc860040 pgd = c0004000 [cc860040] *pgd=0b41e811, *pte=00000000, *ppte=00000000 Internal error: Oops: 7 [#1] ARM CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc3+ #19 Hardware name: BCM2835 task: cb494000 ti: cb4d0000 task.ti: cb4d0000 PC is at dwc2_is_controller_alive+0x18/0x34 LR is at dwc2_handle_common_intr+0x24/0xb60 Acked-by: John Youn Tested-by: Marek Szyprowski Signed-off-by: Stefan Wahren Signed-off-by: Felipe Balbi

usb: dwc2: make otg clk optional

2015-11-19T20:48:49+00:00

Fixes commit 09a75e857790 ("usb: dwc2: refactor common low-level hw code to platform.c") The above commit consolidated the low-level phy access into a common location. This change made the otg clk a requirement and broke some platforms when it was moved into platform.c. So make clk handling optional again. Acked-by: Eric Anholt Signed-off-by: Stefan Wahren Cc: Marek Szyprowski Acked-by: John Youn Tested-by: Marek Szyprowski Fixes: 09a75e857790 ("usb: dwc2: refactor common low-level hw code to platform.c") Signed-off-by: Felipe Balbi

usb: dwc2: Return errors from PHY

2015-11-19T20:48:49+00:00

When searching for PHYs, any error was treated as if the PHY did not exist or was not specified. Thus the probe function did not correctly return error conditions such as -EPROBE_DEFER. Fixed so that only a non-existing PHY is ignored and any other error is returned. Acked-by: Eric Anholt Reported-by: Alexander Aring Signed-off-by: John Youn Signed-off-by: Stefan Wahren Tested-by: Marek Szyprowski Signed-off-by: Felipe Balbi