kernel/linux.git/drivers/usb/dwc2/platform.c, branch v5.10.264

usb: dwc2: fix hang during suspend if set as peripheral

2026-01-19T12:11:33+00:00

[ Upstream commit 2b94b054ac4974ad2f89f7f7461840c851933adb ] dwc2 on most platforms needs phy controller, clock and power supply. All of them must be enabled/activated to properly operate. If dwc2 is configured as peripheral mode, then all the above three hardware resources are disabled at the end of the probe: /* Gadget code manages lowlevel hw on its own */ if (hsotg->dr_mode == USB_DR_MODE_PERIPHERAL) dwc2_lowlevel_hw_disable(hsotg); But the dwc2_suspend() tries to read the dwc2's reg to check whether is_device_mode or not, this would result in hang during suspend if dwc2 is configured as peripheral mode. Fix this hang by bypassing suspend/resume if lowlevel hw isn't enabled. Fixes: 09a75e857790 ("usb: dwc2: refactor common low-level hw code to platform.c") Signed-off-by: Jisheng Zhang Link: https://patch.msgid.link/20251104002503.17158-3-jszhang@kernel.org Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: dwc2: fix hang during shutdown if set as peripheral

2026-01-19T12:11:33+00:00

[ Upstream commit b6ebcfdcac40a27953f052e4269ce75a18825ffc ] dwc2 on most platforms needs phy controller, clock and power supply. All of them must be enabled/activated to properly operate. If dwc2 is configured as peripheral mode, then all the above three hardware resources are disabled at the end of the probe: /* Gadget code manages lowlevel hw on its own */ if (hsotg->dr_mode == USB_DR_MODE_PERIPHERAL) dwc2_lowlevel_hw_disable(hsotg); But dwc2_driver_shutdown() tries to disable the interrupts on HW IP level. This would result in hang during shutdown if dwc2 is configured as peripheral mode. Fix this hang by only disable and sync irq when lowlevel hw is enabled. Fixes: 4fdf228cdf69 ("usb: dwc2: Fix shutdown callback in platform") Signed-off-by: Jisheng Zhang Link: https://patch.msgid.link/20251104002503.17158-2-jszhang@kernel.org Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: dwc2: disable platform lowlevel hw resources during shutdown

2026-01-19T12:11:33+00:00

[ Upstream commit 7481a97c5f49f10c7490bb990d0e863f23b9bb71 ] On some SoC platforms, in shutdown stage, most components' power is cut off, but there's still power supply to the so called always-on domain, so if the dwc2's regulator is from the always-on domain, we need to explicitly disable it to save power. Disable platform lowlevel hw resources such as phy, clock and regulators etc. in device shutdown hook to reduce non-necessary power consumption when the platform enters shutdown stage. Signed-off-by: Jisheng Zhang Acked-by: Minas Harutyunyan Link: https://lore.kernel.org/r/20250629094655.747-1-jszhang@kernel.org Signed-off-by: Greg Kroah-Hartman Stable-dep-of: b6ebcfdcac40 ("usb: dwc2: fix hang during shutdown if set as peripheral") Signed-off-by: Sasha Levin

usb: dwc2: Adjust the timing of USB Driver Interrupt Registration in the Crashkernel Scenario

2024-10-17T13:08:32+00:00

[ Upstream commit 4058c39bd176daf11a826802d940d86292a6b02b ] The issue is that before entering the crash kernel, the DWC USB controller did not perform operations such as resetting the interrupt mask bits. After entering the crash kernel,before the USB interrupt handler registration was completed while loading the DWC USB driver,an GINTSTS_SOF interrupt was received.This triggered the misroute_irq process within the GIC handling framework,ultimately leading to the misrouting of the interrupt,causing it to be handled by the wrong interrupt handler and resulting in the issue. Summary:In a scenario where the kernel triggers a panic and enters the crash kernel,it is necessary to ensure that the interrupt mask bit is not enabled before the interrupt registration is complete. If an interrupt reaches the CPU at this moment,it will certainly not be handled correctly,especially in cases where this interrupt is reported frequently. Please refer to the Crashkernel dmesg information as follows (the message on line 3 was added before devm_request_irq is called by the dwc2_driver_probe function): [ 5.866837][ T1] dwc2 JMIC0010:01: supply vusb_d not found, using dummy regulator [ 5.874588][ T1] dwc2 JMIC0010:01: supply vusb_a not found, using dummy regulator [ 5.882335][ T1] dwc2 JMIC0010:01: before devm_request_irq irq: [71], gintmsk[0xf300080e], gintsts[0x04200009] [ 5.892686][ C0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-jmnd1.2_RC #18 [ 5.900327][ C0] Hardware name: CMSS HyperCard4-25G/HyperCard4-25G, BIOS 1.6.4 Jul 8 2024 [ 5.908836][ C0] Call trace: [ 5.911965][ C0] dump_backtrace+0x0/0x1f0 [ 5.916308][ C0] show_stack+0x20/0x30 [ 5.920304][ C0] dump_stack+0xd8/0x140 [ 5.924387][ C0] pcie_xxx_handler+0x3c/0x1d8 [ 5.930121][ C0] __handle_irq_event_percpu+0x64/0x1e0 [ 5.935506][ C0] handle_irq_event+0x80/0x1d0 [ 5.940109][ C0] try_one_irq+0x138/0x174 [ 5.944365][ C0] misrouted_irq+0x134/0x140 [ 5.948795][ C0] note_interrupt+0x1d0/0x30c [ 5.953311][ C0] handle_irq_event+0x13c/0x1d0 [ 5.958001][ C0] handle_fasteoi_irq+0xd4/0x260 [ 5.962779][ C0] __handle_domain_irq+0x88/0xf0 [ 5.967555][ C0] gic_handle_irq+0x9c/0x2f0 [ 5.971985][ C0] el1_irq+0xb8/0x140 [ 5.975807][ C0] __setup_irq+0x3dc/0x7cc [ 5.980064][ C0] request_threaded_irq+0xf4/0x1b4 [ 5.985015][ C0] devm_request_threaded_irq+0x80/0x100 [ 5.990400][ C0] dwc2_driver_probe+0x1b8/0x6b0 [ 5.995178][ C0] platform_drv_probe+0x5c/0xb0 [ 5.999868][ C0] really_probe+0xf8/0x51c [ 6.004125][ C0] driver_probe_device+0xfc/0x170 [ 6.008989][ C0] device_driver_attach+0xc8/0xd0 [ 6.013853][ C0] __driver_attach+0xe8/0x1b0 [ 6.018369][ C0] bus_for_each_dev+0x7c/0xdc [ 6.022886][ C0] driver_attach+0x2c/0x3c [ 6.027143][ C0] bus_add_driver+0xdc/0x240 [ 6.031573][ C0] driver_register+0x80/0x13c [ 6.036090][ C0] __platform_driver_register+0x50/0x5c [ 6.041476][ C0] dwc2_platform_driver_init+0x24/0x30 [ 6.046774][ C0] do_one_initcall+0x50/0x25c [ 6.051291][ C0] do_initcall_level+0xe4/0xfc [ 6.055894][ C0] do_initcalls+0x80/0xa4 [ 6.060064][ C0] kernel_init_freeable+0x198/0x240 [ 6.065102][ C0] kernel_init+0x1c/0x12c Signed-off-by: Shawn Shao Link: https://lore.kernel.org/r/20240830031709.134-1-shawn.shao@jaguarmicro.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

usb: dwc2: fix a devres leak in hw_enable upon suspend resume

2023-04-05T09:23:40+00:00

commit f747313249b74f323ddf841a9c8db14d989f296a upstream. Each time the platform goes to low power, PM suspend / resume routines call: __dwc2_lowlevel_hw_enable -> devm_add_action_or_reset(). This adds a new devres each time. This may also happen at runtime, as dwc2_lowlevel_hw_enable() can be called from udc_start(). This can be seen with tracing: - echo 1 > /sys/kernel/debug/tracing/events/dev/devres_log/enable - go to low power - cat /sys/kernel/debug/tracing/trace A new "ADD" entry is found upon each low power cycle: ... devres_log: 49000000.usb-otg ADD 82a13bba devm_action_release (8 bytes) ... devres_log: 49000000.usb-otg ADD 49889daf devm_action_release (8 bytes) ... A second issue is addressed here: - regulator_bulk_enable() is called upon each PM cycle (suspend/resume). - regulator_bulk_disable() never gets called. So the reference count for these regulators constantly increase, by one upon each low power cycle, due to missing regulator_bulk_disable() call in __dwc2_lowlevel_hw_disable(). The original fix that introduced the devm_add_action_or_reset() call, fixed an issue during probe, that happens due to other errors in dwc2_driver_probe() -> dwc2_core_reset(). Then the probe fails without disabling regulators, when dr_mode == USB_DR_MODE_PERIPHERAL. Rather fix the error path: disable all the low level hardware in the error path, by using the "hsotg->ll_hw_enabled" flag. Checking dr_mode has been introduced to avoid a dual call to dwc2_lowlevel_hw_disable(). "ll_hw_enabled" should achieve the same (and is used currently in the remove() routine). Fixes: 54c196060510 ("usb: dwc2: Always disable regulators on driver teardown") Fixes: 33a06f1300a7 ("usb: dwc2: Fix error path in gadget registration") Cc: stable Signed-off-by: Fabrice Gasnier Link: https://lore.kernel.org/r/20230316084127.126084-1-fabrice.gasnier@foss.st.com Signed-off-by: Greg Kroah-Hartman

usb: dwc2: fix wrong order of phy_power_on and phy_init

2022-09-08T09:11:39+00:00

commit f9b995b49a07bd0d43b0e490f59be84415c745ae upstream. Since 1599069a62c6 ("phy: core: Warn when phy_power_on is called before phy_init") the driver complains. In my case (Amlogic SoC) the warning is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init So change the order of the two calls. The same change has to be done to the order of phy_exit() and phy_power_off(). Fixes: 09a75e857790 ("usb: dwc2: refactor common low-level hw code to platform.c") Cc: stable@vger.kernel.org Acked-by: Minas Harutyunyan Acked-by: Marek Szyprowski Signed-off-by: Heiner Kallweit Link: https://lore.kernel.org/r/dfcc6b40-2274-4e86-e73c-5c5e6aa3e046@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: dwc2: fix STM ID/VBUS detection startup delay in dwc2_driver_probe

2021-12-22T08:30:56+00:00

commit fac6bf87c55f7f0733efb0375565fb6a50cf2caf upstream. When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies on sensing comparators. This detection needs time to stabilize. A delay was already applied in dwc2_resume() when reactivating the detection, but it wasn't done in dwc2_probe(). This patch adds delay after enabling STM ID/VBUS detection. Then, ID state is good when initializing gadget and host, and avoid to get a wrong Connector ID Status Change interrupt. Fixes: a415083a11cc ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS") Cc: stable Acked-by: Minas Harutyunyan Signed-off-by: Amelie Delaunay Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com Signed-off-by: Greg Kroah-Hartman

usb: dwc2: Avoid leaving the error_debugfs label unused

2020-10-27T09:33:53+00:00

The error_debugfs label is only used when either CONFIG_USB_DWC2_PERIPHERAL or CONFIG_USB_DWC2_DUAL_ROLE is enabled. Add the same #if to the error_debugfs label itself as the code which uses this label already has. This avoids the following compiler warning: warning: label ‘error_debugfs’ defined but not used [-Wunused-label] Fixes: e1c08cf23172ed ("usb: dwc2: Add missing cleanups when usb_add_gadget_udc() fails") Acked-by: Minas Harutyunyan Reported-by: kernel test robot Reported-by: Jens Axboe Signed-off-by: Martin Blumenstingl Signed-off-by: Felipe Balbi

usb: dwc2: override PHY input signals with usb role switch support

2020-10-02T10:29:13+00:00

This patch adds support for usb role switch to dwc2, by using overriding control of the PHY voltage valid and ID input signals. iddig signal (ID) can be overridden: - when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1; - when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0. avalid/bvalid/vbusvalid signals can be overridden respectively with: - GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL - GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL - GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL It is possible to determine valid sessions thanks to usb role switch: - if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid - if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid - if USB_ROLE_HOST then avalid && !bvalid && vbusvalid Acked-by: Minas Harutyunyan Acked-by: Martin Blumenstingl Signed-off-by: Amelie Delaunay Signed-off-by: Felipe Balbi

usb: dwc2: Always disable regulators on driver teardown

2020-10-02T06:57:40+00:00

If the dwc2 driver fails to probe after having enabled the regulators, it ends up being unregistered with regulators enabled, something the core regulator code is legitimately upset about: dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator dwc2 ff400000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE WARNING: CPU: 2 PID: 112 at drivers/regulator/core.c:2074 _regulator_put.part.0+0x16c/0x174 Modules linked in: dwc2(E+) dwc3(E) udc_core(E) rtc_hym8563(E) dwmac_generic(E) ulpi(E) usbcore(E) dwc3_meson_g12a(E) roles(E) meson_gx_mmc(E+) i2c_meson(E) mdio_mux_meson_g12a(E) mdio_mux(E) dwmac_meson8b(E) stmmac_platform(E) stmmac(E) mdio_xpcs(E) phylink(E) of_mdio(E) fixed_phy(E) libphy(E) pwm_regulator(E) fixed(E) CPU: 2 PID: 112 Comm: systemd-udevd Tainted: G E 5.9.0-rc4-00102-g423583bc8cf9 #1840 Hardware name: amlogic w400/w400, BIOS 2020.04 05/22/2020 pstate: 80400009 (Nzcv daif +PAN -UAO BTYPE=--) pc : _regulator_put.part.0+0x16c/0x174 lr : regulator_bulk_free+0x6c/0x9c sp : ffffffc012353820 x29: ffffffc012353820 x28: ffffff805a4b7000 x27: ffffff8059c2eac0 x26: ffffff8059c2e810 x25: ffffff805a4b7d00 x24: ffffffc008cf3028 x23: ffffffc011729ef8 x22: ffffff807e2761d8 x21: ffffffc01171df78 x20: ffffff805a4b7700 x19: ffffff805a4b7700 x18: 0000000000000030 x17: 0000000000000000 x16: 0000000000000000 x15: ffffff807ea8d178 x14: 3935312820435455 x13: 2038323a36313a37 x12: ffffffffffffffff x11: 0000000000000040 x10: 0000000000000007 x9 : ffffffc0106f77d0 x8 : ffffffffffffffe0 x7 : ffffffffffffffff x6 : 0000000000017702 x5 : ffffff805a4b7400 x4 : 0000000000000000 x3 : ffffffc01171df78 x2 : ffffff807ea8cc40 x1 : 0000000000000000 x0 : 0000000000000001 Call trace: _regulator_put.part.0+0x16c/0x174 regulator_bulk_free+0x6c/0x9c devm_regulator_bulk_release+0x28/0x3c release_nodes+0x1c8/0x2c0 devres_release_all+0x44/0x6c really_probe+0x1ec/0x504 driver_probe_device+0x100/0x170 device_driver_attach+0xcc/0xd4 __driver_attach+0xb0/0x17c bus_for_each_dev+0x7c/0xd4 driver_attach+0x30/0x3c bus_add_driver+0x154/0x250 driver_register+0x84/0x140 __platform_driver_register+0x54/0x60 dwc2_platform_driver_init+0x2c/0x1000 [dwc2] do_one_initcall+0x54/0x2d0 do_init_module+0x68/0x29c In order to fix this, tie the regulator disabling to the teardown process by registering a devm action callback. This makes sure that the regulators are disabled at the right time (just before they are released). Cc: Minas Harutyunyan Cc: Greg Kroah-Hartman Signed-off-by: Marc Zyngier Signed-off-by: Felipe Balbi