kernel/linux.git/drivers/usb/core, branch v7.0.12

usb: core: Fix SuperSpeed root hub wMaxPacketSize

2026-06-09T10:32:50+00:00

commit d1e280334b7f0a1df441e08bd1f6a1bcc36b3bbb upstream. There is no good reason to have wBytesPerInterval < wMaxPacketSize - either one is too low or the other too high, and we may want to warn about such descriptors. Start with cleaning up our own root hubs. USB 3.2 section 10.15.1 sets wMaxPacketSize and wBytesPerInterval of SuperSpeed hub status endpoints at 2 bytes, so reduce wMaxPacketSize from its former value of 4, which was derived from USB 2.0 spec and the kernel's USB_MAXCHILDREN limit. They don't apply because USB 3.2 10.15.2.1 specifies SuperSpeed hubs to have up to 15 ports. Suggested-by: Mathias Nyman Signed-off-by: Michal Pecio Link: https://patch.msgid.link/20260518073121.7bc1da0f.michal.pecio@gmail.com Signed-off-by: Greg Kroah-Hartman

USB: quirks: add NO_LPM for Lenovo ThinkPad USB-C Dock Gen2 hub controllers

2026-06-09T10:32:42+00:00

commit 9ddb9c0deca48d2c2a22ebf4d2f35c925a520328 upstream. The Lenovo ThinkPad USB-C Dock Gen2 (17ef:a391, 17ef:a392) hub controllers exhibit link instability when USB Link Power Management is enabled, similar to the dock's Ethernet adapter (17ef:a387) which already carries USB_QUIRK_NO_LPM. When the dock reconnects after a transient disconnect, the hub controllers enter LPM states between re-enumeration retries, causing repeated disconnect/reconnect cycles lasting up to two minutes. Disabling LPM for these devices restores stable enumeration. Signed-off-by: Stephen J. Fuhry Cc: stable Link: https://patch.msgid.link/20260513171419.44849-1-fuhrysteve@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: core: Fix up Interrupt IN endpoints with bogus wBytesPerInterval

2026-06-09T10:32:42+00:00

commit 727d045d064b7c9a24db3bce9c0485a382cb768b upstream. Tao Xue found that some common devices violate USB 3.x section 9.6.7 by reporting wBytesPerInterval lower than the size of packets they actually send. I confirmed that AX88179 may set it to 0 and RTL8153 CDC configuration sets it to 8 but sends both 8 and 16 byte packets: S Ii:11:007:3 -115:128 16 < C Ii:11:007:3 0:128 8 = a1000000 01000000 S Ii:11:007:3 -115:128 16 < C Ii:11:007:3 0:128 16 = a12a0000 01000800 00000000 00000000 Most xHCI host controllers neglect interrupt bandwidth reservations and let such devices exceed theirs, some fail the URB with EOVERFLOW. Assume that wBytesPerInterval lower than wMaxPacketSize is bogus and increase it to the worst case maximum on interrupt IN endpoints. This solves xHCI problems and appears to have no other effect. Interrupt transfers are not limited to one interval and drivers submit URBs of class defined size without looking at wBytesPerInterval. Any multi- interval transfer is considered terminated by a packet shorter than wMaxPacketSize regardless of wBytesPerInterval - see USB3 8.10.3. Stay in spec on OUT endpoints and isochronous. No buggy devices are known and we don't want to risk sending more data than the device is prepared to handle or confusing isoc drivers regarding altsetting capacities guaranteed by the device itself. And don't complain when wMaxPacketSize <= wBytesPerInterval < wMaxPacketSize * (bMaxBurst+1) because enabling this seems to be the exact goal of the spec. Reported-and-tested-by: Tao Xue Closes: https://lore.kernel.org/linux-usb/20260402021400.28853-1-xuetao09@huawei.com/ Cc: stable@vger.kernel.org Signed-off-by: Michal Pecio Link: https://patch.msgid.link/20260518073207.5b7d26e7.michal.pecio@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: port: add delay after usb_hub_set_port_power()

2026-04-22T11:32:18+00:00

commit b84cc80610a8ce036deb987f056ce3196ead7f1e upstream. When a port is disabled, an attached device will be disconnected. This causes a port-status-change event, which will race with hub autosuspend (if the disabled port was the only connected port on its hub), causing an immediate resume and a second autosuspend. Both of these can be avoided by adding a short delay after the call to usb_hub_set_port_power(). Below log shows what is happening: $ echo 1 > usb1-port1/disable [ 37.958239] usb 1-1: USB disconnect, device number 2 [ 37.964101] usb 1-1: unregistering device [ 37.970070] hub 1-0:1.0: hub_suspend [ 37.971305] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 37.974412] usb usb1: bus auto-suspend, wakeup 1 [ 37.988175] usb usb1: suspend raced with wakeup event <--- [ 37.993947] usb usb1: usb auto-resume [ 37.998401] hub 1-0:1.0: hub_resume [ 38.105688] usb usb1-port1: status 0000, change 0000, 12 Mb/s [ 38.112399] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 38.118645] hub 1-0:1.0: hub_suspend [ 38.122963] usb usb1: bus auto-suspend, wakeup 1 [ 38.200368] usb usb1: usb wakeup-resume [ 38.204982] usb usb1: usb auto-resume [ 38.209376] hub 1-0:1.0: hub_resume [ 38.213676] usb usb1-port1: status 0101 change 0001 [ 38.321552] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 38.327978] usb usb1-port1: status 0101, change 0000, 12 Mb/s [ 38.457429] usb 1-1: new high-speed USB device number 3 using ci_hdrc Then, port change bit will be fixed to the final state and usb_clear_port_feature() can correctly clear it after this period. This will also avoid usb runtime suspend routine to run because usb_autopm_put_interface() not run yet. Fixes: f061f43d7418 ("usb: hub: port: add sysfs entry to switch port power") Cc: stable@kernel.org Signed-off-by: Xu Yang Link: https://patch.msgid.link/20260316095042.1559882-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman

usb: core: use dedicated spinlock for offload state

2026-04-02T07:43:26+00:00

Replace the coarse USB device lock with a dedicated offload_lock spinlock to reduce contention during offload operations. Use offload_pm_locked to synchronize with PM transitions and replace the legacy offload_at_suspend flag. Optimize usb_offload_get/put by switching from auto-resume/suspend to pm_runtime_get_if_active(). This ensures offload state is only modified when the device is already active, avoiding unnecessary power transitions. Cc: stable Fixes: ef82a4803aab ("xhci: sideband: add api to trace sideband usage") Signed-off-by: Guan-Yu Lin Tested-by: Hailong Liu Acked-by: Mathias Nyman Link: https://patch.msgid.link/20260401123238.3790062-2-guanyulin@google.com Signed-off-by: Greg Kroah-Hartman

USB: core: add NO_LPM quirk for Razer Kiyo Pro webcam

2026-04-02T07:30:44+00:00

The Razer Kiyo Pro (1532:0e05) is a USB 3.0 UVC webcam whose firmware does not handle USB Link Power Management transitions reliably. When LPM is active, the device can enter a state where it fails to respond to control transfers, producing EPIPE (-32) errors on UVC probe control SET_CUR requests. In the worst case, the stalled endpoint triggers an xHCI stop-endpoint command that times out, causing the host controller to be declared dead and every USB device on the bus to be disconnected. This has been reported as Ubuntu Launchpad Bug #2061177. The failure mode is: 1. UVC probe control SET_CUR returns -32 (EPIPE) 2. xHCI host not responding to stop endpoint command 3. xHCI host controller not responding, assume dead 4. All USB devices on the affected xHCI controller disconnect Disabling LPM prevents the firmware from entering the problematic low- power states that precede the stall. This is the same approach used for other webcams with similar firmware issues (e.g., Logitech HD Webcam C270). Cc: stable Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2061177 Signed-off-by: JP Hein Link: https://patch.msgid.link/20260331003806.212565-2-jp@jphein.com Signed-off-by: Greg Kroah-Hartman

usb: core: phy: avoid double use of 'usb3-phy'

2026-04-02T07:19:31+00:00

Commit 53a2d95df836 ("usb: core: add phy notify connect and disconnect") causes double use of the 'usb3-phy' in certain cases. Since that commit, if a generic PHY named 'usb3-phy' is specified in the device tree, that is getting added to the 'phy_roothub' list of the secondary HCD by the usb_phy_roothub_alloc_usb3_phy() function. However, that PHY is getting added also to the primary HCD's 'phy_roothub' list by usb_phy_roothub_alloc() if there is no generic PHY specified with 'usb2-phy' name. This causes that the usb_add_hcd() function executes each phy operations twice on the 'usb3-phy'. Once when the primary HCD is added, then once again when the secondary HCD is added. The issue affects the Marvell Armada 3700 platform at least, where a custom name is used for the USB2 PHY: $ git grep 'phy-names.*usb3' arch/arm64/boot/dts/marvell/armada-37xx.dtsi | tr '\t' ' ' arch/arm64/boot/dts/marvell/armada-37xx.dtsi: phy-names = "usb3-phy", "usb2-utmi-otg-phy"; Extend the usb_phy_roothub_alloc_usb3_phy() function to skip adding the 'usb3-phy' to the 'phy_roothub' list of the secondary HCD when 'usb2-phy' is not specified in the device tree to avoid the double use. Fixes: 53a2d95df836 ("usb: core: add phy notify connect and disconnect") Cc: stable Signed-off-by: Gabor Juhos Link: https://patch.msgid.link/20260330-usb-avoid-usb3-phy-double-use-v1-1-d2113aecb535@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: quirks: add DELAY_INIT quirk for another Silicon Motion flash drive

2026-03-30T15:04:28+00:00

Another Silicon Motion flash drive also randomly work incorrectly (lsusb does not list the device) on Huawei hisi platforms during 500 reboot cycles, and the DELAY_INIT quirk fixes this issue. Signed-off-by: Miao Li Cc: stable Link: https://patch.msgid.link/20260319053927.264840-1-limiao870622@163.com Signed-off-by: Greg Kroah-Hartman

usb: hcd: queue wakeup_work to system_freezable_wq workqueue

2026-03-18T15:17:08+00:00

After commit 4fb352df14de ("PM: sleep: Do not flag runtime PM workqueue as freezable"), pm_wq workqueue will be unfreezable during system pm. This brings issue as below: [ 344.255749] ------------[ cut here ]------------ [ 344.277740] URB 000000004aae4ad1 submitted while active [ 344.282996] WARNING: drivers/usb/core/urb.c:379 at usb_submit_urb+0x5a4/0x5e0, CPU#2: kworker/u16:14/964 [ 344.292477] Modules linked in: [ 344.295532] CPU: 2 UID: 0 PID: 964 Comm: kworker/u16:14 Not tainted 7.0.0-rc2-next-20260303-00006-gf03fe0b53b39-dirty #100 PREEMPT [ 344.307341] Hardware name: NXP i.MX943 EVK board (DT) [ 344.312386] Workqueue: async async_run_entry_fn [ 344.316919] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 344.323862] pc : usb_submit_urb+0x5a4/0x5e0 [ 344.328046] lr : usb_submit_urb+0x5a4/0x5e0 [ 344.332217] sp : ffff800083283b30 [ 344.335528] x29: ffff800083283b30 x28: ffff000082631000 x27: 0000000000000000 [ 344.342661] x26: 0000000000000003 x25: 0000000000000c00 x24: 0000000000000000 [ 344.349793] x23: 0000000000000004 x22: 0000000000000010 x21: 0000000000000000 [ 344.356917] x20: 0000000000000002 x19: ffff00008253ce40 x18: ffff000089e4eec0 [ 344.364050] x17: 000000040044ffff x16: 000005d9d87f6289 x15: 0000000000000000 [ 344.371174] x14: ffff000089e4eec0 x13: 6576697463612065 x12: 6c69687720646574 [ 344.378298] x11: 0000000000000058 x10: 0000000000000001 x9 : 0000000000000001 [ 344.385431] x8 : 0000000000000000 x7 : 0000005028dd0800 x6 : 0000000000000002 [ 344.392563] x5 : ffffc48f74e9daf8 x4 : 0000000000000000 x3 : 0000000000000000 [ 344.399696] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000089e4ee40 [ 344.406835] Call trace: [ 344.409280] usb_submit_urb+0x5a4/0x5e0 (P) [ 344.413456] hub_activate+0x268/0x878 [ 344.417116] hub_resume+0x5c/0x10c [ 344.420522] usb_resume_interface.isra.0+0xa8/0x110 [ 344.425393] usb_resume_both+0x10c/0x1e0 [ 344.429310] usb_resume+0x1c/0x70 [ 344.432621] usb_dev_resume+0x14/0x20 [ 344.436278] dpm_run_callback.isra.0+0x38/0xf8 [ 344.440715] device_resume+0xec/0x1e8 [ 344.444373] async_resume+0x20/0x38 [ 344.447848] async_run_entry_fn+0x34/0xe0 [ 344.451852] process_one_work+0x150/0x290 [ 344.455856] worker_thread+0x18c/0x300 [ 344.459600] kthread+0x118/0x124 [ 344.462824] ret_from_fork+0x10/0x20 The reason is if the host controller resume routine xhci_resume() call usb_hcd_resume_root_hub(), wakeup_work will be queued and run immediately. Then usb_autoresume_device() will be called and usb device will exit runtime suspended state (if it was suspended before). For a hub device, hub_resume()/hub_reset_resume() will be called accordingly. After the host controller device system resume is finished, the root hub usb device "usb1" will do system resume too. Then hub_resume() will be called again. Above sequence will cause hub->urb to be submitted twice. To avoid this issue, restore the previous behavior by queuing wakeup_work to system_freezable_wq workqueue. Acked-by: Alan Stern Fixes: 4fb352df14de ("PM: sleep: Do not flag runtime PM workqueue as freezable") Cc: stable Signed-off-by: Xu Yang Link: https://patch.msgid.link/20260316094811.1559471-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman

USB: ezcap401 needs USB_QUIRK_NO_BOS to function on 10gbs usb speed

2026-03-13T17:19:07+00:00

Add USB_QUIRK_NO_BOS for ezcap401 capture card, without it dmesg will show "unable to get BOS descriptor or descriptor too short" and "unable to read config index 0 descriptor/start: -71" errors and device will not able to work at full speed at 10gbs Signed-off-by: Vyacheslav Vahnenko Cc: stable Link: https://patch.msgid.link/20260313123638.20481-1-vahnenko2003@gmail.com Signed-off-by: Greg Kroah-Hartman