kernel/linux.git/drivers/usb/core, branch v6.12.96

USB: quirks: add NO_LPM for the Samsung T5 EVO Portable SSD

2026-07-18T14:52:09+00:00

commit fc591787785b9709a0bb65a7df3ba2537d611c47 upstream. The Samsung T5 EVO Portable SSD (04e8:6200) exhibit two forms of link instability when USB Link Power Management is enabled: 1. The units fail to initialize properly on first detection, resulting in a lockup in the drive where it must be power cycled or the kernel will not recognize the presence of the device. 2. If used for sustained operations (small amounts of continuous data are transferred to the unit) then the unit will "hiccup" after roughly 8 hours of use and will disconnect and reconnect. This has a certain probability of triggering the first issue, but also causes mount points to become invalid since the device gets issued a new letter. Signed-off-by: Erich E. Hoover Cc: stable Link: https://patch.msgid.link/20260602204508.48856-1-erich.e.hoover@gmail.com Signed-off-by: Greg Kroah-Hartman

USB: core: add USB_QUIRK_NO_LPM for VIA Labs USB 2.0 hub

2026-07-18T14:52:08+00:00

commit bd728c3d9b1cc0bb0fda6a7055c5c8b55d7477b2 upstream. The VIA Labs, Inc. USB 2.0 hub controller (2109:2817), found in a KVM switch, fails to enumerate high-power devices during cold boot and system restart. Applying the kernel parameter usbcore.quirks=2109:2817:k resolves the issue. Enumeration failure log: usb 1-1.2.3: device descriptor read/64, error -32 usb 1-1.2.3: Device not responding to setup address. usb 1-1.2.3: device not accepting address 11, error -71 usb 1-1.2-port3: unable to enumerate USB device Add USB_QUIRK_NO_LPM for this device. Signed-off-by: Rodrigo Lugathe da Conceição Alves Cc: stable Link: https://patch.msgid.link/20260603113626.395612-1-lugathe2@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: core: Fix SuperSpeed root hub wMaxPacketSize

2026-06-09T10:26:05+00:00

commit d1e280334b7f0a1df441e08bd1f6a1bcc36b3bbb upstream. There is no good reason to have wBytesPerInterval < wMaxPacketSize - either one is too low or the other too high, and we may want to warn about such descriptors. Start with cleaning up our own root hubs. USB 3.2 section 10.15.1 sets wMaxPacketSize and wBytesPerInterval of SuperSpeed hub status endpoints at 2 bytes, so reduce wMaxPacketSize from its former value of 4, which was derived from USB 2.0 spec and the kernel's USB_MAXCHILDREN limit. They don't apply because USB 3.2 10.15.2.1 specifies SuperSpeed hubs to have up to 15 ports. Suggested-by: Mathias Nyman Signed-off-by: Michal Pecio Link: https://patch.msgid.link/20260518073121.7bc1da0f.michal.pecio@gmail.com Signed-off-by: Greg Kroah-Hartman

USB: quirks: add NO_LPM for Lenovo ThinkPad USB-C Dock Gen2 hub controllers

2026-06-09T10:25:57+00:00

commit 9ddb9c0deca48d2c2a22ebf4d2f35c925a520328 upstream. The Lenovo ThinkPad USB-C Dock Gen2 (17ef:a391, 17ef:a392) hub controllers exhibit link instability when USB Link Power Management is enabled, similar to the dock's Ethernet adapter (17ef:a387) which already carries USB_QUIRK_NO_LPM. When the dock reconnects after a transient disconnect, the hub controllers enter LPM states between re-enumeration retries, causing repeated disconnect/reconnect cycles lasting up to two minutes. Disabling LPM for these devices restores stable enumeration. Signed-off-by: Stephen J. Fuhry Cc: stable Link: https://patch.msgid.link/20260513171419.44849-1-fuhrysteve@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: core: Fix up Interrupt IN endpoints with bogus wBytesPerInterval

2026-06-09T10:25:56+00:00

commit 727d045d064b7c9a24db3bce9c0485a382cb768b upstream. Tao Xue found that some common devices violate USB 3.x section 9.6.7 by reporting wBytesPerInterval lower than the size of packets they actually send. I confirmed that AX88179 may set it to 0 and RTL8153 CDC configuration sets it to 8 but sends both 8 and 16 byte packets: S Ii:11:007:3 -115:128 16 < C Ii:11:007:3 0:128 8 = a1000000 01000000 S Ii:11:007:3 -115:128 16 < C Ii:11:007:3 0:128 16 = a12a0000 01000800 00000000 00000000 Most xHCI host controllers neglect interrupt bandwidth reservations and let such devices exceed theirs, some fail the URB with EOVERFLOW. Assume that wBytesPerInterval lower than wMaxPacketSize is bogus and increase it to the worst case maximum on interrupt IN endpoints. This solves xHCI problems and appears to have no other effect. Interrupt transfers are not limited to one interval and drivers submit URBs of class defined size without looking at wBytesPerInterval. Any multi- interval transfer is considered terminated by a packet shorter than wMaxPacketSize regardless of wBytesPerInterval - see USB3 8.10.3. Stay in spec on OUT endpoints and isochronous. No buggy devices are known and we don't want to risk sending more data than the device is prepared to handle or confusing isoc drivers regarding altsetting capacities guaranteed by the device itself. And don't complain when wMaxPacketSize <= wBytesPerInterval < wMaxPacketSize * (bMaxBurst+1) because enabling this seems to be the exact goal of the spec. Reported-and-tested-by: Tao Xue Closes: https://lore.kernel.org/linux-usb/20260402021400.28853-1-xuetao09@huawei.com/ Cc: stable@vger.kernel.org Signed-off-by: Michal Pecio Link: https://patch.msgid.link/20260518073207.5b7d26e7.michal.pecio@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: port: add delay after usb_hub_set_port_power()

2026-04-22T11:18:59+00:00

commit b84cc80610a8ce036deb987f056ce3196ead7f1e upstream. When a port is disabled, an attached device will be disconnected. This causes a port-status-change event, which will race with hub autosuspend (if the disabled port was the only connected port on its hub), causing an immediate resume and a second autosuspend. Both of these can be avoided by adding a short delay after the call to usb_hub_set_port_power(). Below log shows what is happening: $ echo 1 > usb1-port1/disable [ 37.958239] usb 1-1: USB disconnect, device number 2 [ 37.964101] usb 1-1: unregistering device [ 37.970070] hub 1-0:1.0: hub_suspend [ 37.971305] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 37.974412] usb usb1: bus auto-suspend, wakeup 1 [ 37.988175] usb usb1: suspend raced with wakeup event <--- [ 37.993947] usb usb1: usb auto-resume [ 37.998401] hub 1-0:1.0: hub_resume [ 38.105688] usb usb1-port1: status 0000, change 0000, 12 Mb/s [ 38.112399] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 38.118645] hub 1-0:1.0: hub_suspend [ 38.122963] usb usb1: bus auto-suspend, wakeup 1 [ 38.200368] usb usb1: usb wakeup-resume [ 38.204982] usb usb1: usb auto-resume [ 38.209376] hub 1-0:1.0: hub_resume [ 38.213676] usb usb1-port1: status 0101 change 0001 [ 38.321552] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 38.327978] usb usb1-port1: status 0101, change 0000, 12 Mb/s [ 38.457429] usb 1-1: new high-speed USB device number 3 using ci_hdrc Then, port change bit will be fixed to the final state and usb_clear_port_feature() can correctly clear it after this period. This will also avoid usb runtime suspend routine to run because usb_autopm_put_interface() not run yet. Fixes: f061f43d7418 ("usb: hub: port: add sysfs entry to switch port power") Cc: stable@kernel.org Signed-off-by: Xu Yang Link: https://patch.msgid.link/20260316095042.1559882-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman

usb: core: phy: avoid double use of 'usb3-phy'

2026-04-11T12:24:46+00:00

commit 0179c6da0793ae03607002c284b53b6d584172d0 upstream. Commit 53a2d95df836 ("usb: core: add phy notify connect and disconnect") causes double use of the 'usb3-phy' in certain cases. Since that commit, if a generic PHY named 'usb3-phy' is specified in the device tree, that is getting added to the 'phy_roothub' list of the secondary HCD by the usb_phy_roothub_alloc_usb3_phy() function. However, that PHY is getting added also to the primary HCD's 'phy_roothub' list by usb_phy_roothub_alloc() if there is no generic PHY specified with 'usb2-phy' name. This causes that the usb_add_hcd() function executes each phy operations twice on the 'usb3-phy'. Once when the primary HCD is added, then once again when the secondary HCD is added. The issue affects the Marvell Armada 3700 platform at least, where a custom name is used for the USB2 PHY: $ git grep 'phy-names.*usb3' arch/arm64/boot/dts/marvell/armada-37xx.dtsi | tr '\t' ' ' arch/arm64/boot/dts/marvell/armada-37xx.dtsi: phy-names = "usb3-phy", "usb2-utmi-otg-phy"; Extend the usb_phy_roothub_alloc_usb3_phy() function to skip adding the 'usb3-phy' to the 'phy_roothub' list of the secondary HCD when 'usb2-phy' is not specified in the device tree to avoid the double use. Fixes: 53a2d95df836 ("usb: core: add phy notify connect and disconnect") Cc: stable Signed-off-by: Gabor Juhos Link: https://patch.msgid.link/20260330-usb-avoid-usb3-phy-double-use-v1-1-d2113aecb535@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: quirks: add DELAY_INIT quirk for another Silicon Motion flash drive

2026-04-11T12:24:45+00:00

commit dd36014ec6042f424ef51b923e607772f7502ee7 upstream. Another Silicon Motion flash drive also randomly work incorrectly (lsusb does not list the device) on Huawei hisi platforms during 500 reboot cycles, and the DELAY_INIT quirk fixes this issue. Signed-off-by: Miao Li Cc: stable Link: https://patch.msgid.link/20260319053927.264840-1-limiao870622@163.com Signed-off-by: Greg Kroah-Hartman

USB: core: add NO_LPM quirk for Razer Kiyo Pro webcam

2026-04-11T12:24:43+00:00

commit 8b7a42ecdcdeb55580d9345412f7f8fc5aca3f6c upstream. The Razer Kiyo Pro (1532:0e05) is a USB 3.0 UVC webcam whose firmware does not handle USB Link Power Management transitions reliably. When LPM is active, the device can enter a state where it fails to respond to control transfers, producing EPIPE (-32) errors on UVC probe control SET_CUR requests. In the worst case, the stalled endpoint triggers an xHCI stop-endpoint command that times out, causing the host controller to be declared dead and every USB device on the bus to be disconnected. This has been reported as Ubuntu Launchpad Bug #2061177. The failure mode is: 1. UVC probe control SET_CUR returns -32 (EPIPE) 2. xHCI host not responding to stop endpoint command 3. xHCI host controller not responding, assume dead 4. All USB devices on the affected xHCI controller disconnect Disabling LPM prevents the firmware from entering the problematic low- power states that precede the stall. This is the same approach used for other webcams with similar firmware issues (e.g., Logitech HD Webcam C270). Cc: stable Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2061177 Signed-off-by: JP Hein Link: https://patch.msgid.link/20260331003806.212565-2-jp@jphein.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Greg Kroah-Hartman

usb: core: new quirk to handle devices with zero configurations

2026-04-02T11:09:30+00:00

[ Upstream commit 9f6a983cfa22ac662c86e60816d3a357d4b551e9 ] Some USB devices incorrectly report bNumConfigurations as 0 in their device descriptor, which causes the USB core to reject them during enumeration. logs: usb 1-2: device descriptor read/64, error -71 usb 1-2: no configurations usb 1-2: can't read configurations, error -22 However, these devices actually work correctly when treated as having a single configuration. Add a new quirk USB_QUIRK_FORCE_ONE_CONFIG to handle such devices. When this quirk is set, assume the device has 1 configuration instead of failing with -EINVAL. This quirk is applied to the device with VID:PID 5131:2007 which exhibits this behavior. Signed-off-by: Jie Deng Link: https://patch.msgid.link/20260227084931.1527461-1-dengjie03@kylinos.cn Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin