kernel/linux.git/drivers/usb/core, branch v4.19.39

USB: Consolidate LPM checks to avoid enabling LPM twice

2019-05-02T07:58:56+00:00

commit d7a6c0ce8d26412903c7981503bad9e1cc7c45d2 upstream. USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working after S3: [ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin [ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110) After some experiments, I found that disabling LPM can workaround the issue. On some platforms, the USB power is cut during S3, so the driver uses reset-resume to resume the device. During port resume, LPM gets enabled twice, by usb_reset_and_verify_device() and usb_port_resume(). Consolidate all checks into new LPM helpers to make sure LPM only gets enabled once. Fixes: de68bab4fa96 ("usb: Don't enable USB 2.0 Link PM by default.”) Signed-off-by: Kai-Heng Feng Cc: stable # after much soaking Signed-off-by: Greg Kroah-Hartman Signed-off-by: Greg Kroah-Hartman

USB: Add new USB LPM helpers

2019-05-02T07:58:56+00:00

commit 7529b2574a7aaf902f1f8159fbc2a7caa74be559 upstream. Use new helpers to make LPM enabling/disabling more clear. This is a preparation to subsequent patch. Signed-off-by: Kai-Heng Feng Cc: stable # after much soaking Signed-off-by: Greg Kroah-Hartman

usb: hub: delay hub autosuspend if USB3 port is still link training

2019-02-12T18:47:05+00:00

[ Upstream commit e86108940e541febf35813402ff29fa6f4a9ac0b ] When initializing a hub we want to give a USB3 port in link training the same debounce delay time before autosuspening the hub as already trained, connected enabled ports. USB3 ports won't reach the enabled state with "current connect status" and "connect status change" bits set until the USB3 link training finishes. Catching the port in link training (polling) and adding the debounce delay prevents unnecessary failed attempts to autosuspend the hub. Signed-off-by: Mathias Nyman Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

USB: leds: fix regression in usbport led trigger

2019-01-31T07:14:34+00:00

commit 91f7d2e89868fcac0e750a28230fdb1ad4512137 upstream. The patch "usb: simplify usbport trigger" together with "leds: triggers: add device attribute support" caused an regression for the usbport trigger. it will no longer enumerate any active usb hub ports under the "ports" directory in the sysfs class directory, if the usb host drivers are fully initialized before the usbport trigger was loaded. The reason is that the usbport driver tries to register the sysfs entries during the activate() callback. And this will fail with -2 / ENOENT because the patch "leds: triggers: add device attribute support" made it so that the sysfs "ports" group was only being added after the activate() callback succeeded. This version of the patch reverts parts of the "usb: simplify usbport trigger" patch and restores usbport trigger's functionality. Fixes: 6f7b0bad8839 ("usb: simplify usbport trigger") Signed-off-by: Christian Lamparter Cc: stable Acked-by: Jacek Anaszewski Signed-off-by: Greg Kroah-Hartman

USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB

2019-01-16T21:04:32+00:00

commit 3483254b89438e60f719937376c5e0ce2bc46761 upstream. To match the Corsair Strafe RGB, the Corsair K70 RGB also requires USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues discussed here: https://github.com/ckb-next/ckb-next/issues/42. Otherwise roughly 1 in 10 boots the keyboard will fail to be detected. Patch that applied delay control quirk for Corsair Strafe RGB: cb88a0588717 ("usb: quirks: add control message delay for 1b1c:1b20") Previous K70 RGB patch to add delay-init quirk: 7a1646d92257 ("Add delay-init quirk for Corsair K70 RGB keyboards") Signed-off-by: Jack Stocker Cc: stable Signed-off-by: Greg Kroah-Hartman

USB: check usb_get_extra_descriptor for proper size

2018-12-13T08:16:15+00:00

commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream. When reading an extra descriptor, we need to properly check the minimum and maximum size allowed, to prevent from invalid data being sent by a device. Reported-by: Hui Peng Reported-by: Mathias Payer Co-developed-by: Linus Torvalds Signed-off-by: Hui Peng Signed-off-by: Mathias Payer Signed-off-by: Linus Torvalds Cc: stable Signed-off-by: Greg Kroah-Hartman

usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device

2018-12-13T08:16:15+00:00

commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream. Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is in 0781:5591, will aggressively request LPM of U1/U2 during runtime, when using this thumb drive as the OS installation key we found the device will generate failure during U1 exit path making it dropped from the USB bus, this causes a corrupted installation in system at the end. i.e., [ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004 [ 166.918327] usb usb2-port2: link state change [ 166.918337] usb usb2-port2: do warm reset [ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms [ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms [ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s [ 167.276050] usb 2-2: USB disconnect, device number 2 [ 167.276058] usb 2-2: unregistering device [ 167.276060] usb 2-2: unregistering interface 2-2:1.0 [ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk [ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00 ... Analyzed the USB trace in the link layer we realized it is because of the 6-ms timer of tRecoveryConfigurationTimeout which documented on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from Recovery.Configuration"; device initiates U1 exit -> Recovery.Active -> Recovery.Configuration, then the host timer timeout makes the link transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset. Interestingly, the other higher volume of SanDisk Ultra Flair sharing the same VID:PID, such as 64GB, would not request LPM during runtime, it sticks at U0 always, thus disabling LPM does not affect those thumb drives at all. The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583. Signed-off-by: Harry Pan Cc: stable Signed-off-by: Greg Kroah-Hartman

usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream series

2018-12-05T18:32:13+00:00

commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream. Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to function correctly. This fixes a but where double pressing numlock locks up the device completely with need to replug the keyboard. Signed-off-by: Michael Niewöhner Tested-by: Michael Niewöhner Cc: stable Signed-off-by: Greg Kroah-Hartman

usb: core: Fix hub port connection events lost

2018-12-01T08:37:24+00:00

commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream. This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset only if a device is was attached to the hub port before resetting the hub port. Using a Lenovo T480s attached to the ultra dock it was not possible to detect some usb-c devices at the dock usb-c ports because the hub_port_reset code will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset. Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit. This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the new device was attached such that it was not detected. This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is currently no device attached to the port before the hub port reset. This will avoid clearing the connection bit for new attached devices. Signed-off-by: Dennis Wassenberg Acked-by: Mathias Nyman Cc: stable Signed-off-by: Greg Kroah-Hartman

usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB

2018-11-27T15:13:10+00:00

commit a77112577667cbda7c6292c52d909636aef31fd9 upstream. Following on from this patch: https://lkml.org/lkml/2017/11/3/516, Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to start correctly at boot. Dmesg output: usb 1-6: string descriptor 0 read error: -110 usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33 usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-6: can't set config #1, error -110 Signed-off-by: Emmanuel Pescosta Cc: stable Signed-off-by: Greg Kroah-Hartman