kernel/linux.git/drivers/usb/Kconfig, branch linux-2.6.35.y

Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6

2010-03-03T16:48:58+00:00

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits) USB: backlight, appledisplay: fix incomplete registration failure handling USB: pl2303: remove unnecessary reset of usb_device in urbs USB: ftdi_sio: remove obsolete check in unthrottle USB: ftdi_sio: remove unused tx_bytes counter USB: qcaux: driver for auxiliary serial ports on Qualcomm devices USB: pl2303: initial TIOCGSERIAL support USB: option: add Longcheer/Longsung vendor ID USB: fix I2C API usage in ohci-pnx4008. USB: usbmon: mask seconds properly in text API USB: sisusbvga: no unnecessary GFP_ATOMIC USB: storage: onetouch: unnecessary GFP_ATOMIC USB: serial: ftdi: add CONTEC vendor and product id USB: remove references to port->port.count from the serial drivers USB: tty: Prune uses of tty_request_room in the USB layer USB: tty: Add a function to insert a string of characters with the same flag USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration() USB: tty: kill request_room for USB ACM class USB: tty: sort out the request_room handling for whiteheat USB: storage: fix misplaced parenthesis USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers ...

USB: OHCI: DA8xx/OMAP-L1x glue layer

2010-03-02T22:55:06+00:00

Texas Instruments DA8xx/OMAP-L1x OHCI glue layer. This OHCI implementation is not without quirks: there's only one physical port despite the root hub reporting two; the port's power control and over-current status bits are not connected to any pins, however, at least on the DA830 EVM board, those signals are connected via GPIO, thus the provision was made for overriding the OHCI port power and over-current bits at the board level... Signed-off-by: Mikhail Cherkashin Signed-off-by: Sergei Shtylyov Signed-off-by: Greg Kroah-Hartman

USB: host: SL811: allow the hcd on Blackfin systems

2010-03-02T22:53:27+00:00

Signed-off-by: Michael Hennerich Signed-off-by: Bryan Wu Signed-off-by: Mike Frysinger Signed-off-by: Greg Kroah-Hartman

omap3: Replace ARCH_OMAP34XX with ARCH_OMAP3

2010-02-15T17:27:02+00:00

Replace ARCH_OMAP34XX with ARCH_OMAP3 Signed-off-by: Tony Lindgren

USB: ehci: Allow EHCI to be built on OMAP3

2009-12-11T19:55:20+00:00

usb: ehci: Allow EHCI to be built on OMAP3 OMAP3 chips have a built-in EHCI controller. The recently introduced omap ehci-hcd driver missed out on selecting USB_ARCH_HAS_EHCI in Kconfig. Without this, the driver cannot be built. Signed-off-by: Anand Gadiyar Cc: Vikram Pandita Cc: Ajay Kumar Gupta Acked-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

USB: Add EHCI support for MX27 and MX31 based boards

2009-12-11T19:55:18+00:00

The Freescale MX27 and MX31 SoCs have a EHCI controller onboard. The controller is capable of USB on the go. This patch adds a driver to support all three of them. Users have to pass details about serial interface configuration in the platform data. The USB OTG core used here is the ARC core, so the driver should be renamed and probably be merged with ehci-fsl.c eventually. Signed-off-by: Sascha Hauer Signed-off-by: Daniel Mack Cc: David Brownell Signed-off-by: Greg Kroah-Hartman

Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze

2009-09-24T16:01:44+00:00

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (24 commits) microblaze: Disable heartbeat/enable emaclite in defconfigs microblaze: Support simpleImage.dts make target microblaze: Fix _start symbol to physical address microblaze: Use LOAD_OFFSET macro to get correct LMA for all sections microblaze: Create the LOAD_OFFSET macro used to compute VMA vs LMA offsets microblaze: Copy ppc asm-compat.h for clean handling of constants in asm and C microblaze: Actually show KiB rather than pages in "Freeing initrd memory:" microblaze: Support ptrace syscall tracing. microblaze: Updated CPU version and FPGA family codes in PVR microblaze: Generate correct signal and siginfo for integer div-by-zero microblaze: Don't be noisy when userspace causes hardware exceptions microblaze: Remove ipc.h file which points to non-existing asm-generic file microblaze: Clear sticky FSR register after generating exception signals microblaze: Ensure CPU usermode is set on new userspace processes microblaze: Use correct kbuild variable KBUILD_CFLAGS microblaze: Save and restore msr in hw exception microblaze: Add architectural support for USB EHCI host controllers microblaze: Implement include/asm/syscall.h. microblaze: Improve checking mechanism for MSR instruction microblaze: Add checking mechanism for MSR instruction ...

USB: at91: Add USB EHCI driver for at91sam9g45 series

2009-09-23T13:46:30+00:00

Add host USB High speed driver for at91sam9g45 series. The host driver is an EHCI with its companion OHCI. EHCI is handled by the new ehci-atmel.c whereas the OHCI is always handled by ohci-at91.c. Signed-off-by: Nicolas Ferre Acked-by: David Brownell

USB: Add nuvoton Ehci driver for w90p910 platform

2009-09-23T13:46:20+00:00

Add ehci support for w90p910 platform. Signed-off-by: Wan ZongShun Cc: David Brownell Signed-off-by: Greg Kroah-Hartman

microblaze: Add architectural support for USB EHCI host controllers

2009-09-22T06:50:14+00:00

Add architectural support for USB EHCI host controllers. It has been tested using the USB EHCI host controller from Xilinx Inc., using both High Speed devices and Full Speed devices. Signed-off-by: Julie Zhu Signed-off-by: Michal Simek