kernel/linux.git/drivers/tty, branch linux-5.9.y

serial: 8250_omap: Avoid FIFO corruption caused by MDR1 access

2020-12-21T12:28:20+00:00

commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream. It has been observed that once per 300-1300 port openings the first transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared as "e" on the wire). It only happened if single byte has been transmitted right after port open, which means, DMA is not used for this transfer and the corruption never happened afterwards. Therefore I've carefully re-read the MDR1 errata (link below), which says "when accessing the MDR1 registers that causes a dummy under-run condition that will freeze the UART in IrDA transmission. In UART mode, this may corrupt the transferred data". Strictly speaking, omap_8250_mdr1_errataset() performs a read access and if the value is the same as should be written, exits without errata-recommended FIFO reset. A brief check of the serial_omap_mdr1_errataset() from the competing omap-serial driver showed it has no read access of MDR1. After removing the read access from omap_8250_mdr1_errataset() the data corruption never happened any more. Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com Signed-off-by: Greg Kroah-Hartman

tty: Fix ->session locking

2020-12-11T12:22:04+00:00

commit c8bcd9c5be24fb9e6132e97da5a35e55a83e36b9 upstream. Currently, locking of ->session is very inconsistent; most places protect it using the legacy tty mutex, but disassociate_ctty(), __do_SAK(), tiocspgrp() and tiocgsid() don't. Two of the writers hold the ctrl_lock (because they already need it for ->pgrp), but __proc_set_tty() doesn't do that yet. On a PREEMPT=y system, an unprivileged user can theoretically abuse this broken locking to read 4 bytes of freed memory via TIOCGSID if tiocgsid() is preempted long enough at the right point. (Other things might also go wrong, especially if root-only ioctls are involved; I'm not sure about that.) Change the locking on ->session such that: - tty_lock() is held by all writers: By making disassociate_ctty() hold it. This should be fine because the same lock can already be taken through the call to tty_vhangup_session(). The tricky part is that we need to shorten the area covered by siglock to be able to take tty_lock() without ugly retry logic; as far as I can tell, this should be fine, since nothing in the signal_struct is touched in the `if (tty)` branch. - ctrl_lock is held by all writers: By changing __proc_set_tty() to hold the lock a little longer. - All readers that aren't holding tty_lock() hold ctrl_lock: By adding locking to tiocgsid() and __do_SAK(), and expanding the area covered by ctrl_lock in tiocspgrp(). Cc: stable@kernel.org Signed-off-by: Jann Horn Reviewed-by: Jiri Slaby Signed-off-by: Greg Kroah-Hartman

tty: Fix ->pgrp locking in tiocspgrp()

2020-12-11T12:22:04+00:00

commit 54ffccbf053b5b6ca4f6e45094b942fab92a25fc upstream. tiocspgrp() takes two tty_struct pointers: One to the tty that userspace passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`). These pointers are different when ioctl() is called with a master fd. To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock. This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on both sides of a PTY pair to corrupt the refcount of `struct pid`, leading to use-after-free errors. Fixes: 47f86834bbd4 ("redo locking of tty->pgrp") CC: stable@kernel.org Signed-off-by: Jann Horn Reviewed-by: Jiri Slaby Signed-off-by: Greg Kroah-Hartman

serial: ar933x_uart: disable clk on error handling path in probe

2020-11-24T12:39:10+00:00

commit 425af483523b76bc78e14674a430579d38b2a593 upstream. ar933x_uart_probe() does not invoke clk_disable_unprepare() on one error handling path. This patch fixes that. Fixes: 9be1064fe524 ("serial: ar933x_uart: add RS485 support") Reported-by: Hulk Robot Signed-off-by: Zheng Zengkai Link: https://lore.kernel.org/r/20201111124426.42638-1-zhengzengkai@huawei.com Cc: stable Signed-off-by: Greg Kroah-Hartman

tty: serial: imx: keep console clocks always on

2020-11-24T12:39:08+00:00

commit e67c139c488e84e7eae6c333231e791f0e89b3fb upstream. For below code, there has chance to cause deadlock in SMP system: Thread 1: clk_enable_lock(); pr_info("debug message"); clk_enable_unlock(); Thread 2: imx_uart_console_write() clk_enable() clk_enable_lock(); Thread 1: Acuired clk enable_lock -> printk -> console_trylock_spinning Thread 2: console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock So the patch is to keep console port clocks always on like other console drivers. Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check") Acked-by: Uwe Kleine-König Signed-off-by: Fugang Duan Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com Cc: stable [fix up build warning - gregkh] Signed-off-by: Greg Kroah-Hartman

tty: serial: imx: fix potential deadlock

2020-11-24T12:39:08+00:00

commit 33f16855dcb973f745c51882d0e286601ff3be2b upstream. Enabling the lock dependency validator has revealed that the way spinlocks are used in the IMX serial port could result in a deadlock. Specifically, imx_uart_int() acquires a spinlock without disabling the interrupts, meaning that another interrupt could come along and try to acquire the same spinlock, potentially causing the two to wait for each other indefinitely. Use spin_lock_irqsave() instead to disable interrupts upon acquisition of the spinlock. Fixes: c974991d2620 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr") Reviewed-by: Uwe Kleine-König Signed-off-by: Sam Nobs Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com Cc: stable Signed-off-by: Greg Kroah-Hartman

serial: txx9: add missing platform_driver_unregister() on error in serial_txx9_init

2020-11-10T11:39:09+00:00

commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream. Add the missing platform_driver_unregister() before return from serial_txx9_init in the error handling case when failed to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI defined. Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/") Signed-off-by: Qinglang Miao Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com Cc: stable Signed-off-by: Greg Kroah-Hartman

serial: 8250_mtk: Fix uart_get_baud_rate warning

2020-11-10T11:39:09+00:00

commit 912ab37c798770f21b182d656937072b58553378 upstream. Mediatek 8250 port supports speed higher than uartclk / 16. If the baud rates in both the new and the old termios setting are higher than uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered. Passing NULL as the old termios so uart_get_baud_rate() will use uartclk / 16 - 1 as the new baud rate which will be replaced by the original baud rate later by tty_termios_encode_baud_rate() in mtk8250_set_termios(). Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping") Signed-off-by: Claire Chang Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org Cc: stable Signed-off-by: Greg Kroah-Hartman

tty: fix crash in release_tty if tty->port is not set

2020-11-10T11:39:07+00:00

commit 4466d6d2f80c1193e0845d110277c56da77a6418 upstream. Commit 2ae0b31e0face ("tty: don't crash in tty_init_dev when missing tty_port") didn't fully prevent the crash as the cleanup path in tty_init_dev() calls release_tty() which dereferences tty->port without checking it for non-null. Add tty->port checks to release_tty to avoid the kernel crash. Fixes: 2ae0b31e0face ("tty: don't crash in tty_init_dev when missing tty_port") Signed-off-by: Matthias Reichl Link: https://lore.kernel.org/r/20201105123432.4448-1-hias@horus.com Cc: stable Signed-off-by: Greg Kroah-Hartman

tty: serial: imx: enable earlycon by default if IMX_SERIAL_CONSOLE is enabled

2020-11-10T11:39:07+00:00

commit 427627a23c3e86e31113f9db9bfdca41698a0ee5 upstream. Since 699cc4dfd140 (tty: serial: imx: add imx earlycon driver), the earlycon part of imx serial is a separate driver and isn't necessarily enabled anymore when the console is enabled. This causes users to loose the earlycon functionality when upgrading their kenrel configuration via oldconfig. Enable earlycon by default when IMX_SERIAL_CONSOLE is enabled. Fixes: 699cc4dfd140 (tty: serial: imx: add imx earlycon driver) Reviewed-by: Fabio Estevam Reviewed-by: Fugang Duan Signed-off-by: Lucas Stach Link: https://lore.kernel.org/r/20201105204026.1818219-1-l.stach@pengutronix.de Cc: stable Signed-off-by: Greg Kroah-Hartman