kernel/linux.git/drivers/tty/serial/sh-sci.c, branch v3.18.100

serial: sh-sci: prevent lockup on full TTY buffers

2018-03-18T10:15:44+00:00

commit 7842055bfce4bf0170d0f61df8b2add8399697be upstream. When the TTY buffers fill up to the configured maximum, a system lockup occurs: [ 598.820128] INFO: rcu_preempt detected stalls on CPUs/tasks: [ 598.825796] 0-...!: (1 GPs behind) idle=5a6/2/0 softirq=1974/1974 fqs=1 [ 598.832577] (detected by 3, t=62517 jiffies, g=296, c=295, q=126) [ 598.838755] Task dump for CPU 0: [ 598.841977] swapper/0 R running task 0 0 0 0x00000022 [ 598.849023] Call trace: [ 598.851476] __switch_to+0x98/0xb0 [ 598.854870] (null) This can be prevented by doing a dummy read of the RX data register. This issue affects both HSCIF and SCIF ports. Reported for R-Car H3 ES2.0; reproduced and fixed on H3 ES1.1. Probably affects other R-Car platforms as well. Reported-by: Yoshihiro Shimoda Signed-off-by: Ulrich Hecht Reviewed-by: Geert Uytterhoeven Cc: stable Tested-by: Nguyen Viet Dung Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix register offsets for the IRDA serial port

2017-11-15T09:04:12+00:00

[ Upstream commit a752ba18af8285e3eeda572f40dddaebff0c3621 ] Even though most of its registers are 8-bit wide, the IRDA has two 16-bit registers that make it a 16-bit peripheral and not a 8-bit peripheral with addresses shifted by one. Fix the registers offset in the driver and the platform data regshift value. Signed-off-by: Laurent Pinchart Reviewed-by: Geert Uytterhoeven Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix panic when serial console and DMA are enabled

2017-06-14T10:54:20+00:00

commit 3c9101766b502a0163d1d437fada5801cf616be2 upstream. This patch fixes an issue that kernel panic happens when DMA is enabled and we press enter key while the kernel booting on the serial console. * An interrupt may occur after sci_request_irq(). * DMA transfer area is initialized by setup_timer() in sci_request_dma() and used in interrupt. If an interrupt occurred between sci_request_irq() and setup_timer() in sci_request_dma(), DMA transfer area has not been initialized yet. So, this patch changes the order of sci_request_irq() and sci_request_dma(). Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.") Signed-off-by: Takatoshi Akiyama [Shimoda changes the commit log] Signed-off-by: Yoshihiro Shimoda Cc: Jiri Slaby Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: use dmaengine_terminate_all() API

2014-10-15T16:01:00+00:00

The drivers should use dmaengine_terminate_all() API instead of accessing the device_control which will be deprecated soon Acked-by: Greg Kroah-Hartman Signed-off-by: Vinod Koul

serial: sh-sci: Add calculation recive margin for HSCIF

2014-07-18T01:14:44+00:00

When the error of the same bit rate is detected, we will need to select the recive margin is large. Current code holds the minimum error, it does not have to check the recive margin. This adds this calculation. Signed-off-by: Nobuhiro Iwamatsu Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix range check of bit-rate for HSCIF

2014-07-18T01:14:44+00:00

If bit-rate calculation result of HSCIF is expect 255 from 0, driver does not calculate error bit. However, we need to round the value to calculate error bit in the case of negative value. This rounds the value of bit-rate using clamp(), and bit-rate is the case of negative value, it enables the calculation of the error bit. Signed-off-by: Nobuhiro Iwamatsu Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Updated calculation of bit error rate and bit rate

2014-07-18T01:14:44+00:00

Currently, the decimal point is discarded calculation of BRR. Therefore, it can not calculate a value close to the correct value. This patch fixes this problem by using DIV_ROUND_CLOSEST. Signed-off-by: Nobuhiro Iwamatsu Signed-off-by: Greg Kroah-Hartman

serial: treewide: Remove empty implementations of enable_ms()

2014-07-10T00:29:38+00:00

Signed-off-by: Alexander Shiyan Signed-off-by: Greg Kroah-Hartman

Merge tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2014-04-01T23:55:57+00:00

Pull tty/serial driver update from Greg KH: "Here's the big tty/serial driver update for 3.15-rc1. Nothing major, a number of serial driver updates and a few tty core fixes as well. All have been in linux-next for a while" * tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits) tty/serial: omap: empty the RX FIFO at the end of half-duplex TX tty/serial: omap: fix RX interrupt enable/disable in half-duplex TX serial: sh-sci: Neaten dev_ uses serial: sh-sci: Replace hardcoded 3 by UART_PM_STATE_OFF serial: sh-sci: Add more register documentation serial: sh-sci: Remove useless casts serial: sh-sci: Replace printk() by pr_*() serial_core: Avoid NULL pointer dereference in uart_close() serial_core: Get a reference for port->tty in uart_remove_one_port() serial: clps711x: Give a chance to perform useful tasks during wait loop serial_core: Grammar s/ports/port's/ serial_core: Spelling s/contro/control/ serial: efm32: properly namespace location property serial: max310x: Add missing #include synclink: fix info leak in ioctl serial: 8250: Clean up the locking for -rt serial: 8250_pci: change BayTrail default uartclk serial: 8250_pci: more BayTrail error-free bauds serial: sh-sci: Add missing call to uart_remove_one_port() in failure path serial_core: Unregister console in uart_remove_one_port() ...

cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}

2014-03-19T13:10:24+00:00

Two cpufreq notifiers CPUFREQ_RESUMECHANGE and CPUFREQ_SUSPENDCHANGE have not been used for some time, so remove them to clean up code a bit. Signed-off-by: Viresh Kumar Reviewed-by: Srivatsa S. Bhat [rjw: Changelog] Signed-off-by: Rafael J. Wysocki