kernel/linux.git/drivers/tty/serial/atmel_serial.c, branch v6.7

serial: atmel: Use port lock wrappers

2023-09-18T09:18:10+00:00

When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner Signed-off-by: John Ogness Link: https://lore.kernel.org/r/20230914183831.587273-22-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman

tty: Explicitly include correct DT includes

2023-07-25T18:19:05+00:00

The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Signed-off-by: Rob Herring Acked-by: Uwe Kleine-König # for imx Link: https://lore.kernel.org/r/20230724205440.767071-1-robh@kernel.org Signed-off-by: Greg Kroah-Hartman

serial: drivers: switch ch and flag to u8

2023-07-25T17:21:04+00:00

Now that the serial layer explicitly expects 'u8' for flags and characters, propagate this type to drivers' (RX) routines. Note that amba-pl011's, clps711x's and st-asc's 'ch' are left unchanged because 'ch' contains not only a character, but whole status. Signed-off-by: Jiri Slaby (SUSE) Cc: Tobias Klauser Cc: Russell King Cc: Vineet Gupta Cc: Richard Genoud Cc: Nicolas Ferre Cc: Alexandre Belloni Cc: Claudiu Beznea Cc: Alexander Shiyan Cc: Baruch Siach Cc: "Maciej W. Rozycki" Cc: Taichi Sugaya Cc: Takao Orito Cc: Shawn Guo Cc: Sascha Hauer Cc: Pengutronix Kernel Team Cc: Fabio Estevam Cc: NXP Linux Team Cc: Kevin Cernekee Cc: Krzysztof Kozlowski Cc: Alim Akhtar Cc: Laxman Dewangan Cc: Thierry Reding Cc: Jonathan Hunter Cc: Palmer Dabbelt Cc: Paul Walmsley Cc: Orson Zhai Cc: Baolin Wang Cc: Chunyan Zhang Cc: Patrice Chotard Cc: Maxime Coquelin Cc: Alexandre Torgue Cc: Hammer Hsieh Acked-by: Richard GENOUD Acked-by: Tobias Klauser Acked-by: Thierry Reding Acked-by: Maciej W. Rozycki Link: https://lore.kernel.org/r/20230712081811.29004-11-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman

serial: atmel: don't enable IRQs prematurely

2023-06-21T15:54:33+00:00

The atmel_complete_tx_dma() function disables IRQs at the start of the function by calling spin_lock_irqsave(&port->lock, flags); There is no need to disable them a second time using the spin_lock_irq() function and, in fact, doing so is a bug because it will enable IRQs prematurely when we call spin_unlock_irq(). Just use spin_lock/unlock() instead without disabling or enabling IRQs. Fixes: 08f738be88bb ("serial: at91: add tx dma support") Signed-off-by: Dan Carpenter Reviewed-by: Jiri Slaby Acked-by: Richard Genoud Link: https://lore.kernel.org/r/cb7c39a9-c004-4673-92e1-be4e34b85368@moroto.mountain Cc: stable Signed-off-by: Greg Kroah-Hartman

serial: Make uart_remove_one_port() return void

2023-05-13T10:48:16+00:00

The return value is only ever used as a return value for remove callbacks of platform drivers. This return value is ignored by the driver core. (The only effect is an error message, but uart_remove_one_port() already emitted one in this case.) So the return value isn't used at all and uart_remove_one_port() can be changed to return void without any loss. Also this better matches the Linux device model as remove functions are not supposed to fail. Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20230512173810.131447-3-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman

serial: atmel: fix incorrect baudrate setup

2023-01-19T15:24:39+00:00

Commit ba47f97a18f2 ("serial: core: remove baud_rates when serial console setup") changed uart_set_options to select the correct baudrate configuration based on the absolute error between requested baudrate and available standard baudrate settings. Prior to that commit the baudrate was selected based on which predefined standard baudrate did not exceed the requested baudrate. This change of selection logic was never reflected in the atmel serial driver. Thus the comment left in the atmel serial driver is no longer accurate. Additionally the manual rounding up described in that comment and applied via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses tty_termios_encode_baud_rate to determine the appropriate baudrate flags this can cause baudrate selection to fail entirely because tty_termios_encode_baud_rate will only select a baudrate if relative error between requested and selected baudrate does not exceed +/-2%. Fix that by requesting actual, exact baudrate used by the serial. Fixes: ba47f97a18f2 ("serial: core: remove baud_rates when serial console setup") Cc: stable Signed-off-by: Tobias Schramm Acked-by: Richard Genoud Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org Signed-off-by: Greg Kroah-Hartman

serial: atmel: don't stop the transmitter when doing PIO

2022-11-23T08:39:24+00:00

Writing ATMEL_US_TXDIS to ATMEL_US_CR makes the transmitter NOT to send the just queued character. This means when the character is last and uart calls ops->stop_tx(), the character is not sent at all. The usart datasheet is not much specific on this, it just says the transmitter is stopped. But apparently, the character is dropped. So we should stop the transmitter only for DMA and PDC transfers to not send any more characters. For PIO, this is unexpected and deviates from other drivers. In particular, the below referenced commit broke TX as it added a call to ->stop_tx() after the very last character written to the transmitter. So fix this by limiting the write of ATMEL_US_TXDIS to DMA transfers only. Even there, I don't know if it is correctly implemented. Are all the queued characters sent once ->start_tx() is called? Anyone tested flow control -- be it hard (RTSCTS) or the soft (XOFF/XON) one? Fixes: 2d141e683e9a ("tty: serial: use uart_port_tx() helper") Cc: Richard Genoud Cc: Nicolas Ferre Cc: Alexandre Belloni Cc: Claudiu Beznea Cc: linux-arm-kernel@lists.infradead.org Reported-by: Michael Walle Signed-off-by: Jiri Slaby (SUSE) Link: https://lore.kernel.org/r/20221123082736.24566-2-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman

serial: atmel: cleanup atmel_start+stop_tx()

2022-11-23T08:39:24+00:00

Define local variables holding information about whether pdc or dma is used in the HW. These are retested several times by calls to atmel_use_pdc_tx() and atmel_use_dma_tx(). So to make the code more readable, simply cache the values. This is also a preparatory patch for the next one (where is_pdc is used once more in atmel_stop_tx()). Cc: Richard Genoud Cc: Nicolas Ferre Cc: Alexandre Belloni Cc: Claudiu Beznea Cc: linux-arm-kernel@lists.infradead.org Reported-by: Michael Walle Signed-off-by: Jiri Slaby (SUSE) Link: https://lore.kernel.org/r/20221123082736.24566-1-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman

serial: atmel: Use uart_xmit_advance()

2022-11-03T02:35:41+00:00

Take advantage of the new uart_xmit_advance() helper. Reviewed-by: Claudiu Beznea Acked-By: Richard GENOUD Signed-off-by: Ilpo Järvinen Link: https://lore.kernel.org/r/20221019091151.6692-12-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman

tty: serial: use uart_port_tx() helper

2022-11-03T02:32:40+00:00

uart_port_tx() is a new helper to send characters to the device. Use it in these drivers. Cc: Tobias Klauser Cc: Richard Genoud Cc: Nicolas Ferre Cc: Alexandre Belloni Cc: Claudiu Beznea Cc: Vladimir Zapolskiy Cc: Liviu Dudau Cc: Sudeep Holla Cc: Lorenzo Pieralisi Cc: Shawn Guo Cc: Sascha Hauer Cc: Pengutronix Kernel Team Cc: Fabio Estevam Cc: NXP Linux Team Cc: "Andreas Färber" Cc: Manivannan Sadhasivam Reviewed-by: Ilpo Järvinen Signed-off-by: Jiri Slaby (SUSE) Link: https://lore.kernel.org/r/20221004104927.14361-3-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman