kernel/linux.git/drivers/tty/serial/8250, branch v4.19.77

serial: 8250: Fix TX interrupt handling condition

2019-07-31T05:27:00+00:00

[ Upstream commit db1b5bc047b3cadaedab3826bba82c3d9e023c4b ] Interrupt handler checked THRE bit (transmitter holding register empty) in LSR to detect if TX fifo is empty. In case when there is only receive interrupts the TX handling got called because THRE bit in LSR is set when there is no transmission (FIFO empty). TX handling caused TX stop, which in RS-485 half-duplex mode actually resets receiver FIFO. This is not desired during reception because of possible data loss. The fix is to check if THRI is set in IER in addition of the TX fifo status. THRI in IER is set when TX is started and cleared when TX is stopped. This ensures that TX handling is only called when there is really transmission on going and an interrupt for THRE and not when there are only RX interrupts. Signed-off-by: Kimmo Rautkoski Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"

2019-07-14T06:11:19+00:00

commit 3f2640ed7be838c3f05c0d2b0f7c7508e7431e48 upstream. This reverts commit 2e9fe539108320820016f78ca7704a7342788380. Reading LSR unconditionally but processing the error flags only if UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission error information on UARTs where the transmission error flags are cleared by a read of LSR. Information are lost in case an error is detected right before the read of LSR while processing e.g. an UART_IIR_THRI interrupt. Signed-off-by: Oliver Barta Reviewed-by: Andy Shevchenko Fixes: 2e9fe5391083 ("serial: 8250: Don't service RX FIFO if interrupts are disabled") Cc: stable Signed-off-by: Greg Kroah-Hartman

dmaengine: idma64: Use actual device for DMA transfers

2019-06-15T09:54:10+00:00

[ Upstream commit 5ba846b1ee0792f5a596b9b0b86d6e8cdebfab06 ] Intel IOMMU, when enabled, tries to find the domain of the device, assuming it's a PCI one, during DMA operations, such as mapping or unmapping. Since we are splitting the actual PCI device to couple of children via MFD framework (see drivers/mfd/intel-lpss.c for details), the DMA device appears to be a platform one, and thus not an actual one that performs DMA. In a such situation IOMMU can't find or allocate a proper domain for its operations. As a result, all DMA operations are failed. In order to fix this, supply parent of the platform device to the DMA engine framework and fix filter functions accordingly. We may rely on the fact that parent is a real PCI device, because no other configuration is present in the wild. Signed-off-by: Andy Shevchenko Acked-by: Mark Brown Acked-by: Greg Kroah-Hartman [for tty parts] Signed-off-by: Vinod Koul Signed-off-by: Sasha Levin

serial: 8250_pxa: honor the port number from devicetree

2019-04-05T20:33:01+00:00

[ Upstream commit fe9ed6d2483fda55465f32924fb15bce0fac3fac ] Like the other OF-enabled drivers, use the port number from the firmware if the devicetree specifies an alias: aliases { ... serial2 = &uart2; /* Should be ttyS2 */ } This is how the deprecated pxa.c driver behaved, switching to 8250_pxa messes up the numbering. Signed-off-by: Lubomir Rintel Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()

2019-03-23T19:10:06+00:00

commit 78d3820b9bd39028727c6aab7297b63c093db343 upstream. The four port Pericom chips have the fourth port at the wrong address. Make use of quirk to fix it. Fixes: c8d192428f52 ("serial: 8250: added acces i/o products quad and octal serial cards") Cc: stable Signed-off-by: Jay Dolan Signed-off-by: Greg Kroah-Hartman

serial: 8250_pci: Fix number of ports for ACCES serial cards

2019-03-23T19:10:06+00:00

commit b896b03bc7fce43a07012cc6bf5e2ab2fddf3364 upstream. Have the correct number of ports created for ACCES serial cards. Two port cards show up as four ports, and four port cards show up as eight. Fixes: c8d192428f52 ("serial: 8250: added acces i/o products quad and octal serial cards") Signed-off-by: Jay Dolan Cc: stable Signed-off-by: Greg Kroah-Hartman

serial: 8250_of: assume reg-shift of 2 for mrvl,mmp-uart

2019-03-23T19:10:06+00:00

commit f4817843e39ce78aace0195a57d4e8500a65a898 upstream. There are two other drivers that bind to mrvl,mmp-uart and both of them assume register shift of 2 bits. There are device trees that lack the property and rely on that assumption. If this driver wins the race to bind to those devices, it should behave the same as the older deprecated driver. Signed-off-by: Lubomir Rintel Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman

serial: 8250_pci: Make PCI class test non fatal

2019-02-12T18:47:26+00:00

commit 824d17c57b0abbcb9128fb3f7327fae14761914b upstream. As has been reported the National Instruments serial cards have broken PCI class. The commit 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list") made the PCI class check mandatory for the case when device is listed in a quirk list. Make PCI class test non fatal to allow broken card be enumerated. Fixes: 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list") Cc: stable Reported-by: Guan Yung Tseng Tested-by: Guan Yung Tseng Tested-by: KHUENY.Gerhard Signed-off-by: Andy Shevchenko Signed-off-by: Greg Kroah-Hartman

tty: serial: 8250_mtk: always resume the device in probe.

2018-12-13T08:16:22+00:00

commit 100bc3e2bebf95506da57cbdf5f26b25f6da4c81 upstream. serial8250_register_8250_port calls uart_config_port, which calls config_port on the port before it tries to power on the port. So we need the port to be on before calling serial8250_register_8250_port. Change the code to always do a runtime resume in probe before registering port, and always do a runtime suspend in remove. This basically reverts the change in commit 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling"), but still use pm_runtime callbacks. Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling") Signed-off-by: Peter Shih Cc: stable Signed-off-by: Greg Kroah-Hartman

serial: 8250_of: Fix for lack of interrupt support

2018-11-21T08:19:11+00:00

[ Upstream commit a27d938251ef40c43db81af16fc26b2cec181d4d ] In commit c58caaab3bf8 ("serial: 8250: of: Defer probe on missing IRQ"), a check was added for the UART driver being probed prior to the parent IRQ controller. Unfortunately this breaks certain boards which have no interrupt support, like Huawei D03. Indeed, the 8250 DT bindings state that interrupts should be supported - not must. To fix, switch from irq_of_parse_and_map() to of_irq_get(), which does relay whether the IRQ host controller domain is not ready, i.e. defer probe, instead of assuming it. Fixes: c58caaab3bf8 ("serial: 8250: of: Defer probe on missing IRQ") Signed-off-by: John Garry Reviewed-by: Rob Herring Reviewed-by: Alexander Sverdlin Tested-by: Alexander Sverdlin Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman