kernel/linux.git/drivers/thunderbolt/Kconfig, branch v6.6.132

Merge tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next

2022-09-30T11:44:59+00:00

Mika writes: "thunderbolt: Changes for v6.1 merge window This includes following Thunderbolt/USB4 changes for the v6.1 merge window: - Support for Intel Meteor Lake integrated Thunderbolt/USB4 controller - Support for ASMedia USB4 controller NVM firmware upgrade - Receiver lane margining support - Few fixes and cleanups. All these have been in linux-next with no reported issues." * tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: thunderbolt: Explicitly enable lane adapter hotplug events at startup thunderbolt: Use dev_err_probe() thunderbolt: Convert to use sysfs_emit()/sysfs_emit_at() APIs thunderbolt: Fix spelling mistake "simultaneusly" -> "simultaneously" thunderbolt: debugfs: Fix spelling mistakes in seq_puts text thunderbolt: Add support for ASMedia NVM image format thunderbolt: Move vendor specific NVM handling into nvm.c thunderbolt: Provide tb_retimer_nvm_read() analogous to tb_switch_nvm_read() thunderbolt: Rename and make nvm_read() available for other files thunderbolt: Extend NVM version fields to 32-bits thunderbolt: Allow NVM upgrade of USB4 host routers thunderbolt: Add support for receiver lane margining thunderbolt: Add helper to check if CL states are enabled on port thunderbolt: Pass CL state bitmask to tb_port_clx_supported() thunderbolt: Move port CL state functions into correct place in switch.c thunderbolt: Move tb_xdomain_parent() to tb.h thunderbolt: Add support for Intel Meteor Lake thunderbolt: Add comment where Thunderbolt 4 PCI IDs start thunderbolt: Add DP OUT resource when DP tunnel is discovered

thunderbolt: Add support for receiver lane margining

2022-09-05T06:02:16+00:00

USB4 spec defines standard set of registers to be used for receiver lane margining. This is useful for I/O interface quality and electrical robustness validation during manufacturing. Expose receiver lane margining through new debugfs directory "margining" that is added under each connected USB4 port. Users can then run the margining by writing to the exposed attributes under that directory. Signed-off-by: Mika Westerberg

kunit: fix Kconfig for build-in tests USB4 and Nitro Enclaves

2022-09-01T19:00:48+00:00

Both the USB4 and Nitro Enclaves KUNIT tests are now able to be compiled if KUNIT is compiled as a module. This leads to issues if KUNIT is being packaged separately from the core kernel and when KUNIT is run baremetal without the required driver compiled into the kernel. Fixes: 635dcd16844b ("thunderbolt: test: Use kunit_test_suite() macro") Fixes: fe5be808fa6c ("nitro_enclaves: test: Use kunit_test_suite() macro") Signed-off-by: Nico Pache Reviewed-by: David Gow Reviewed-by: Andra Paraschiv Acked-by: Brendan Higgins Signed-off-by: Shuah Khan

thunderbolt: test: Use kunit_test_suite() macro

2022-07-11T23:13:21+00:00

The new implementation of kunit_test_suite() for modules no longer conflicts with module_init, so can now be used by the thunderbolt tests. Also update the Kconfig entry to enable the test when KUNIT_ALL_TESTS is enabled. This means that kunit_tool can now successfully run and parse the test results with, for example: ./tools/testing/kunit/kunit.py run --arch=x86_64 \ --kconfig_add CONFIG_PCI=y --kconfig_add CONFIG_USB4=y \ 'thunderbolt' Acked-by: Mika Westerberg Acked-by: Daniel Latypov Acked-by: Brendan Higgins Signed-off-by: David Gow Signed-off-by: Shuah Khan

thunderbolt: Add DMA traffic test driver

2020-11-11T07:20:16+00:00

This driver allows sending DMA traffic over XDomain connection. Specifically over a loopback connection using either a Thunderbolt/USB4 cable that is connected back to the host router port, or a special loopback dongle that has RX and TX lines crossed. This can be useful at manufacturing floor to check whether Thunderbolt/USB4 ports are functional. The driver exposes debugfs directory under the XDomain service that can be used to configure the driver, start the test and check the results. If a loopback dongle is used the steps to send and receive 1000 packets can be done like: # modprobe thunderbolt_dma_test # echo 1000 > /sys/kernel/debug/thunderbolt//dma_test/packets_to_receive # echo 1000 > /sys/kernel/debug/thunderbolt//dma_test/packets_to_send # echo 1 > /sys/kernel/debug/thunderbolt//dma_test/test # cat /sys/kernel/debug/thunderbolt//dma_test/status When a cable is connected back to host then there are two Thunderbolt services, one is configured for receiving (does not matter which one): # modprobe thunderbolt_dma_test # echo 1000 > /sys/kernel/debug/thunderbolt//dma_test/packets_to_receive # echo 1 > /sys/kernel/debug/thunderbolt//dma_test/test The other one for sending: # echo 1000 > /sys/kernel/debug/thunderbolt//dma_test/packets_to_send # echo 1 > /sys/kernel/debug/thunderbolt//dma_test/test Results can be read from both services status attributes. Signed-off-by: Isaac Hazan Signed-off-by: Mika Westerberg Acked-by: Yehezkel Bernat Reviewed-by: Greg Kroah-Hartman

thunderbolt: Use "if USB4" instead of "depends on" in Kconfig

2020-09-16T11:57:46+00:00

This groups the USB4 options more nicely, and also does not require that every config option lists explicit depends on USB4. Signed-off-by: Mika Westerberg

thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m

2020-09-16T11:57:46+00:00

This adds a bit more build coverage for the tests even though these are not expected to be enabled by normal users and distros. In order to make this working we need to open-code kunit_test_suite() and call the relevant functions directly in the driver init/exit hook. Signed-off-by: Mika Westerberg

thunderbolt: Add debugfs interface

2020-09-03T09:21:08+00:00

This adds debugfs interface that can be used for debugging possible issues in hardware/software. It exposes router and adapter config spaces through files like this: /sys/kernel/debug/thunderbolt//regs /sys/kernel/debug/thunderbolt///regs /sys/kernel/debug/thunderbolt///path /sys/kernel/debug/thunderbolt///counters /sys/kernel/debug/thunderbolt///regs /sys/kernel/debug/thunderbolt///path /sys/kernel/debug/thunderbolt///counters ... The "regs" is either the router or port configuration space register dump. The "path" is the port path configuration space and "counters" is the optional counters configuration space. These files contains one register per line so it should be easy to use normal filtering tools to find the registers of interest if needed. The router and adapter regs file becomes writable when CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done in production systems) and in this case the developer can write "offset value" lines there to modify the hardware directly. For convenience this also supports the long format the read side produces (but ignores the additional fields). The counters file can be written even when CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear the counter values. Signed-off-by: Gil Fine Signed-off-by: Mika Westerberg Reviewed-by: Greg Kroah-Hartman

thunderbolt: Add KUnit tests for path walking

2020-06-22T16:58:20+00:00

This adds KUnit tests for path walking which is only dependent on software structures, so no hardware is needed to run these. We make these available only when both KUnit and the driver itself are built into the kernel image. The reason for this is that KUnit adds its own module_init() call in kunit_test_suite() which generates linker error because the driver does the same in nhi.c. This should be fine for now because these tests are only meant to run by developers anyway. Signed-off-by: Mika Westerberg

thunderbolt: Improve USB4 config symbol help text

2020-06-15T11:34:21+00:00

Fix the spelling of "specification", and add a missing "the" article. Signed-off-by: Geert Uytterhoeven Signed-off-by: Mika Westerberg