kernel/linux.git/drivers/staging/comedi, branch v4.14.217

staging: comedi: mf6x4: Fix AI end-of-conversion detection

2020-12-29T12:47:06+00:00

commit 56c90457ebfe9422496aac6ef3d3f0f0ea8b2ec2 upstream. I have had reports from two different people that attempts to read the analog input channels of the MF624 board fail with an `ETIMEDOUT` error. After triggering the conversion, the code calls `comedi_timeout()` with `mf6x4_ai_eoc()` as the callback function to check if the conversion is complete. The callback returns 0 if complete or `-EBUSY` if not yet complete. `comedi_timeout()` returns `-ETIMEDOUT` if it has not completed within a timeout period which is propagated as an error to the user application. The existing code considers the conversion to be complete when the EOLC bit is high. However, according to the user manuals for the MF624 and MF634 boards, this test is incorrect because EOLC is an active low signal that goes high when the conversion is triggered, and goes low when the conversion is complete. Fix the problem by inverting the test of the EOLC bit state. Fixes: 04b565021a83 ("comedi: Humusoft MF634 and MF624 DAQ cards driver") Cc: # v4.4+ Cc: Rostislav Lisovy Signed-off-by: Ian Abbott Link: https://lore.kernel.org/r/20201207145806.4046-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman

staging: comedi: cb_pcidas: Allow 2-channel commands for AO subdevice

2020-11-05T10:07:06+00:00

commit 647a6002cb41d358d9ac5de101a8a6dc74748a59 upstream. The "cb_pcidas" driver supports asynchronous commands on the analog output (AO) subdevice for those boards that have an AO FIFO. The code (in `cb_pcidas_ao_check_chanlist()` and `cb_pcidas_ao_cmd()`) to validate and set up the command supports output to a single channel or to two channels simultaneously (the boards have two AO channels). However, the code in `cb_pcidas_auto_attach()` that initializes the subdevices neglects to initialize the AO subdevice's `len_chanlist` member, leaving it set to 0, but the Comedi core will "correct" it to 1 if the driver neglected to set it. This limits commands to use a single channel (either channel 0 or 1), but the limit should be two channels. Set the AO subdevice's `len_chanlist` member to be the same value as the `n_chan` member, which will be 2. Cc: Signed-off-by: Ian Abbott Link: https://lore.kernel.org/r/20201021122142.81628-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman

staging: comedi: check validity of wMaxPacketSize of usb endpoints found

2020-10-17T08:29:54+00:00

commit e1f13c879a7c21bd207dc6242455e8e3a1e88b40 upstream. While finding usb endpoints in vmk80xx_find_usb_endpoints(), check if wMaxPacketSize = 0 for the endpoints found. Some devices have isochronous endpoints that have wMaxPacketSize = 0 (as required by the USB-2 spec). However, since this doesn't apply here, wMaxPacketSize = 0 can be considered to be invalid. Reported-by: syzbot+009f546aa1370056b1c2@syzkaller.appspotmail.com Tested-by: syzbot+009f546aa1370056b1c2@syzkaller.appspotmail.com Signed-off-by: Anant Thazhemadam Cc: stable Link: https://lore.kernel.org/r/20201010082933.5417-1-anant.thazhemadam@gmail.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Greg Kroah-Hartman

staging: comedi: addi_apci_1564: check INSN_CONFIG_DIGITAL_TRIG shift

2020-07-29T05:42:57+00:00

commit 926234f1b8434c4409aa4c53637aa3362ca07cea upstream. The `INSN_CONFIG` comedi instruction with sub-instruction code `INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is used as a right shift amount for other bitmask values without being checked. Shift amounts greater than or equal to 32 will result in undefined behavior. Add code to deal with this. Fixes: 1e15687ea472 ("staging: comedi: addi_apci_1564: add Change-of-State interrupt subdevice and required functions") Cc: #3.17+ Signed-off-by: Ian Abbott Link: https://lore.kernel.org/r/20200717145257.112660-4-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman

staging: comedi: addi_apci_1500: check INSN_CONFIG_DIGITAL_TRIG shift

2020-07-29T05:42:57+00:00

commit fc846e9db67c7e808d77bf9e2ef3d49e3820ce5d upstream. The `INSN_CONFIG` comedi instruction with sub-instruction code `INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is used as a right shift amount for other bitmask values without being checked. Shift amounts greater than or equal to 32 will result in undefined behavior. Add code to deal with this, adjusting the checks for invalid channels so that enabled channel bits that would have been lost by shifting are also checked for validity. Only channels 0 to 15 are valid. Fixes: a8c66b684efaf ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions") Cc: #4.0+: ef75e14a6c93: staging: comedi: verify array index is correct before using it Cc: #4.0+ Signed-off-by: Ian Abbott Link: https://lore.kernel.org/r/20200717145257.112660-5-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman

staging: comedi: ni_6527: fix INSN_CONFIG_DIGITAL_TRIG support

2020-07-29T05:42:57+00:00

commit f07804ec77d77f8a9dcf570a24154e17747bc82f upstream. `ni6527_intr_insn_config()` processes `INSN_CONFIG` comedi instructions for the "interrupt" subdevice. When `data[0]` is `INSN_CONFIG_DIGITAL_TRIG` it is configuring the digital trigger. When `data[2]` is `COMEDI_DIGITAL_TRIG_ENABLE_EDGES` it is configuring rising and falling edge detection for the digital trigger, using a base channel number (or shift amount) in `data[3]`, a rising edge bitmask in `data[4]` and falling edge bitmask in `data[5]`. If the base channel number (shift amount) is greater than or equal to the number of channels (24) of the digital input subdevice, there are no changes to the rising and falling edges, so the mask of channels to be changed can be set to 0, otherwise the mask of channels to be changed, and the rising and falling edge bitmasks are shifted by the base channel number before calling `ni6527_set_edge_detection()` to change the appropriate registers. Unfortunately, the code is comparing the base channel (shift amount) to the interrupt subdevice's number of channels (1) instead of the digital input subdevice's number of channels (24). Fix it by comparing to 32 because all shift amounts for an `unsigned int` must be less than that and everything from bit 24 upwards is ignored by `ni6527_set_edge_detection()` anyway. Fixes: 110f9e687c1a8 ("staging: comedi: ni_6527: support INSN_CONFIG_DIGITAL_TRIG") Cc: # 3.17+ Signed-off-by: Ian Abbott Link: https://lore.kernel.org/r/20200717145257.112660-2-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman

staging: comedi: addi_apci_1032: check INSN_CONFIG_DIGITAL_TRIG shift

2020-07-29T05:42:56+00:00

commit 0bd0db42a030b75c20028c7ba6e327b9cb554116 upstream. The `INSN_CONFIG` comedi instruction with sub-instruction code `INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is used as a right shift amount for other bitmask values without being checked. Shift amounts greater than or equal to 32 will result in undefined behavior. Add code to deal with this. Fixes: 33cdce6293dcc ("staging: comedi: addi_apci_1032: conform to new INSN_CONFIG_DIGITAL_TRIG") Cc: #3.8+ Signed-off-by: Ian Abbott Link: https://lore.kernel.org/r/20200717145257.112660-3-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman

staging: comedi: verify array index is correct before using it

2020-07-22T07:22:24+00:00

[ Upstream commit ef75e14a6c935eec82abac07ab68e388514e39bc ] This code reads from the array before verifying that "trig" is a valid index. If the index is wildly out of bounds then reading from an invalid address could lead to an Oops. Fixes: a8c66b684efa ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions") Signed-off-by: Dan Carpenter Reviewed-by: Ian Abbott Link: https://lore.kernel.org/r/20200709102936.GA20875@mwanda Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

staging: comedi: Fix comedi_device refcnt leak in comedi_open

2020-05-02T15:24:36+00:00

commit 332e0e17ad49e084b7db670ef43b5eb59abd9e34 upstream. comedi_open() invokes comedi_dev_get_from_minor(), which returns a reference of the COMEDI device to "dev" with increased refcount. When comedi_open() returns, "dev" becomes invalid, so the refcount should be decreased to keep refcount balanced. The reference counting issue happens in one exception handling path of comedi_open(). When "cfp" allocation is failed, the refcnt increased by comedi_dev_get_from_minor() is not decreased, causing a refcnt leak. Fix this issue by calling comedi_dev_put() on this error path when "cfp" allocation is failed. Fixes: 20f083c07565 ("staging: comedi: prepare support for per-file read and write subdevices") Signed-off-by: Xiyu Yang Cc: stable Signed-off-by: Xin Tan Signed-off-by: Ian Abbott Link: https://lore.kernel.org/r/1587361459-83622-1-git-send-email-xiyuyang19@fudan.edu.cn Signed-off-by: Greg Kroah-Hartman Signed-off-by: Greg Kroah-Hartman

staging: comedi: dt2815: fix writing hi byte of analog output

2020-05-02T15:24:35+00:00

commit ed87d33ddbcd9a1c3b5ae87995da34e6f51a862c upstream. The DT2815 analog output command is 16 bits wide, consisting of the 12-bit sample value in bits 15 to 4, the channel number in bits 3 to 1, and a voltage or current selector in bit 0. Both bytes of the 16-bit command need to be written in turn to a single 8-bit data register. However, the driver currently only writes the low 8-bits. It is broken and appears to have always been broken. Electronic copies of the DT2815 User's Manual seem impossible to find online, but looking at the source code, a best guess for the sequence the driver intended to use to write the analog output command is as follows: 1. Wait for the status register to read 0x00. 2. Write the low byte of the command to the data register. 3. Wait for the status register to read 0x80. 4. Write the high byte of the command to the data register. Step 4 is missing from the driver. Add step 4 to (hopefully) fix the driver. Also add a "FIXME" comment about setting bit 0 of the low byte of the command. Supposedly, it is used to choose between voltage output and current output, but the current driver always sets it to 1. Signed-off-by: Ian Abbott Cc: stable Link: https://lore.kernel.org/r/20200406142015.126982-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman Signed-off-by: Greg Kroah-Hartman