kernel/linux.git/drivers/soc/tegra, branch v5.7.4

Merge tag 'tegra-for-5.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc

2020-03-25T19:56:55+00:00

soc/tegra: Changes for v5.7-rc1 These changes implement various clocks that are controlled by the PMC and add support for configuring the voltage level of some pins (needed for example to support high-speed modes on the SD/MMC interfaces). * tag 'tegra-for-5.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: soc/tegra: pmc: Cleanup whitespace usage soc/tegra: pmc: Add pins for Tegra194 soc/tegra: Add support for 32 kHz blink clock soc/tegra: Add Tegra PMC clocks registration into PMC driver dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding dt-bindings: phy: tegra-xusb: Add usb-role-switch dt-bindings: phy: tegra: Add Tegra194 support dt-bindings: soc: tegra-pmc: Add ID for Tegra PMC 32 kHz blink clock dt-bindings: soc: tegra-pmc: Add Tegra PMC clock bindings dt-bindings: tegra: Convert Tegra PMC bindings to YAML dt-bindings: clock: tegra: Add IDs for OSC clocks Link: https://lore.kernel.org/r/20200313165848.2915133-3-thierry.reding@gmail.com Signed-off-by: Arnd Bergmann

soc/tegra: pmc: Cleanup whitespace usage

2020-03-13T09:53:10+00:00

Avoid using a mixture of tabs and spaces within tables to make them easier to read and more consistently formatted. Signed-off-by: Thierry Reding

soc/tegra: pmc: Add pins for Tegra194

2020-03-13T09:53:10+00:00

Extend the Tegra194 IO pad table with additional information such as pin names and 1.8/3.3 V settings to allow a table of voltage control pins to generated from it. This is similar to what's done for older chips and is needed to support high-speed modes for SDHCI where switching the pins to 1.8V or 3.3V is necessary. Signed-off-by: Venkat Reddy Talla Signed-off-by: Thierry Reding

soc/tegra: Add support for 32 kHz blink clock

2020-03-13T09:53:06+00:00

Tegra PMC has blink control to output 32 kHz clock out to Tegra blink pin. Blink pad DPD state and enable controls are part of Tegra PMC register space. Currently Tegra clock driver registers blink control by passing PMC address and register offset to clk_register_gate which performs direct PMC access during clk_ops and with this when PMC is in secure mode, any access from non-secure world does not go through. This patch adds blink control registration to the Tegra PMC driver using PMC specific clock gate operations that use tegra_pmc_readl() and tegra_pmc_writel() to support both secure mode and non-secure mode PMC register access. Tested-by: Dmitry Osipenko Reviewed-by: Dmitry Osipenko Signed-off-by: Sowjanya Komatineni Signed-off-by: Thierry Reding

soc/tegra: Add Tegra PMC clocks registration into PMC driver

2020-03-13T09:52:53+00:00

Tegra PMC has clk_out_1, clk_out_2, and clk_out_3 clocks and currently these PMC clocks are registered by Tegra clock driver with each clock as separate mux and gate clocks using clk_register_mux and clk_register_gate by passing PMC base address and register offsets and PMC programming for these clocks happens through direct PMC access by the clock driver. With this, when PMC is in secure mode any direct PMC access from the non-secure world does not go through and these clocks will not be functional. This patch adds these PMC clocks registration to pmc driver with PMC as a clock provider and registers each clock as single clock. clk_ops callback implementations for these clocks uses tegra_pmc_readl and tegra_pmc_writel which supports PMC programming in both secure mode and non-secure mode. Tested-by: Dmitry Osipenko Reviewed-by: Dmitry Osipenko Signed-off-by: Sowjanya Komatineni Signed-off-by: Thierry Reding

soc/tegra: fuse: Fix build with Tegra194 configuration

2020-02-11T23:00:15+00:00

If only Tegra194 support is enabled, the tegra30_fuse_read() and tegra30_fuse_init() function are not declared and cause a build failure. Add Tegra194 to the preprocessor guard to make sure these functions are available for Tegra194-only builds as well. Link: https://lore.kernel.org/r/20200203143114.3967295-1-thierry.reding@gmail.com Reported-by: kbuild test robot Signed-off-by: Thierry Reding Signed-off-by: Olof Johansson

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2020-02-08T22:04:19+00:00

Pull ARM SoC-related driver updates from Olof Johansson: "Various driver updates for platforms: - Nvidia: Fuse support for Tegra194, continued memory controller pieces for Tegra30 - NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC - NXP/FSL: i.MX8MP SoC driver pieces - TI Keystone: ring accelerator driver - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs. - Xilinx ZynqMP: feature checking interface for firmware. Mailbox communication for power management - Overall support patch set for cpuidle on more complex hierarchies (PSCI-based) and misc cleanups, refactorings of Marvell, TI, other platforms" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits) drivers: soc: xilinx: Use mailbox IPI callback dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists MAINTAINERS: Add brcmstb PCIe controller entry soc/tegra: fuse: Unmap registers once they are not needed anymore soc/tegra: fuse: Correct straps' address for older Tegra124 device trees soc/tegra: fuse: Warn if straps are not ready soc/tegra: fuse: Cache values of straps and Chip ID registers memory: tegra30-emc: Correct error message for timed out auto calibration memory: tegra30-emc: Firm up hardware programming sequence memory: tegra30-emc: Firm up suspend/resume sequence soc/tegra: regulators: Do nothing if voltage is unchanged memory: tegra: Correct reset value of xusb_hostr soc/tegra: fuse: Add APB DMA dependency for Tegra20 bus: tegra-aconnect: Remove PM_CLK dependency dt-bindings: mediatek: add MT6765 power dt-bindings soc: mediatek: cmdq: delete not used define memory: tegra: Add support for the Tegra194 memory controller memory: tegra: Only include support for enabled SoCs memory: tegra: Support DVFS on Tegra186 and later ...

soc/tegra: fuse: Unmap registers once they are not needed anymore

2020-01-10T14:59:43+00:00

Both Chip ID and strapping registers are now read out during of APB MISC initialization, the registers' mapping isn't needed anymore once registers are read. Hence let's unmap registers once they are not needed anymore, for consistency. Suggested-by: Michał Mirosław Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding

soc/tegra: fuse: Correct straps' address for older Tegra124 device trees

2020-01-10T14:59:01+00:00

Trying to read out Chip ID before APBMISC registers are mapped won't succeed, in a result Tegra124 gets a wrong address for the HW straps register if machine uses an old outdated device tree. Fixes: 297c4f3dcbff ("soc/tegra: fuse: Restrict legacy code to 32-bit ARM") Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding

soc/tegra: fuse: Warn if straps are not ready

2020-01-10T14:58:48+00:00

Now both Chip ID and HW straps are becoming available at the same time, thus we could simply check the availability of the ID in order to check the availability of the straps. We couldn't check straps for 0x0 because it could be a correct value. This change didn't uncover any problems, but anyways it is nicer to have straps verified for consistency with the Chip ID verification. Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding