kernel/linux.git/drivers/serial/Makefile, branch linux-2.6.22.y

[ARM] 4332/2: KS8695: Serial driver

2007-05-11T21:02:52+00:00

A driver for the KS8695 internal UART. Based on the 2.6.9 driver from Micrel. Signed-off-by: Andrew Victor Signed-off-by: Russell King

blackfin: serial driver

2007-05-07T19:12:58+00:00

This patch implements the driver necessary use the Analog Devices Blackfin processor's Serial Port. Signed-off-by: Bryan Wu Cc: Alan Cox Cc: Russell King Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

[PATCH] PNX8550 UART driver

2007-02-14T16:09:52+00:00

Add UART support for PNX8330/8550/8950 Philips MIPS-based SoCs. Signed-off-by: Vitaly Wool Cc: Russell King Cc: Alan Cox Cc: Ralf Baechle Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

[POWERPC] Open Firmware serial port driver

2007-02-14T00:50:04+00:00

This can be used for serial ports that are connected to an OF platform bus but are not autodetected by the lecacy serial support. It will automatically take over devices that come from the legacy serial detection, which usually is only one device. In some cases, rtas may be set up to use the serial port in the firmware, which allows easier debugging before probing the serial ports. In this case, the "used-by-rtas" property must be set by the firmware. This patch also adds code to the legacy serial driver to check for this. Signed-off-by: Arnd Bergmann Signed-off-by: Paul Mackerras

[PATCH] Exar quad port serial

2006-12-07T16:39:35+00:00

This is on our "Envoy" boxes which we have, according to the documentation, an "Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two other "on-board" serial ports and a modem chip. The two on-board serial UARTs were being detected along with the first two Exar UARTs. The last two Exar UARTs were not showing up and neither was the modem. This patch was the only way I could the kernel to see beyond the standard four serial ports and get all four of the Exar UARTs to show up. [akpm@osdl.org: build fix] Signed-off-by: Paul B Schroeder Cc: Lennart Sorensen Acked-by: Alan Cox Cc: Russell King Cc: Greg KH Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

[PATCH] serial uartlite driver

2006-12-07T16:39:30+00:00

Add a driver for the Xilinx uartlite serial controller used in boards with the PPC405 core in the Xilinx V2P/V4 fpgas. The hardware is very simple (baudrate/start/stopbits fixed and no break support). See the datasheet for details: http://www.xilinx.com/bvdocs/ipcenter/data_sheet/opb_uartlite.pdf See http://thread.gmane.org/gmane.linux.serial/1237/ for the email thread. Signed-off-by: Peter Korsgaard Acked-by: Olof Johansson Cc: Russell King Cc: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

[PATCH] at91_serial -> atmel_serial: Kconfig symbols

2006-10-04T17:25:05+00:00

Rename the following Kconfig symbols: * CONFIG_SERIAL_AT91 -> CONFIG_SERIAL_ATMEL * CONFIG_SERIAL_AT91_CONSOLE -> CONFIG_SERIAL_ATMEL_CONSOLE * CONFIG_SERIAL_AT91_TTYAT -> CONFIG_SERIAL_ATMEL_TTYAT Signed-off-by: Haavard Skinnemoen Acked-by: Andrew Victor Signed-off-by: Linus Torvalds

[PATCH] at91_serial -> atmel_serial: at91_serial.c

2006-10-04T17:25:05+00:00

Rename at91_serial.c atmel_serial.c Signed-off-by: Haavard Skinnemoen Acked-by: Andrew Victor Signed-off-by: Linus Torvalds

[ARM] 3571/1: netX: serial driver for Hilscher netX

2006-06-19T12:29:07+00:00

Patch from Sascha Hauer This patch adds the serial driver for Hilscher's netX network processors. Signed-off-by: Robert Schwebel Signed-off-by: Sascha Hauer Signed-off-by: Russell King

[SERIAL] Allow 8250 PCI, PNP, GSC and HP300 support to be disabled

2006-03-29T21:03:38+00:00

Allow the 8250 probe modules to be disabled if we're building for with EMBEDDED enabled. This reduces the kernel size by not including unnecessary probe module support. Original idea from Matt Mackall for PCI only, expanded to others by rmk. Signed-off-by: Russell King