kernel/linux.git/drivers/scsi, branch v5.10.264

scsi: sg: Report request-table problems when any status is set

2026-07-24T13:49:13+00:00

commit 1d3a742afeb761eaead774691bde1ced699e9a5d upstream. SG_GET_REQUEST_TABLE reports per-request diagnostic state through sg_req_info::problem. The field is meant to indicate whether there is an error to report for a completed request. sg_fill_request_table() currently combines masked_status, host_status and driver_status with bitwise AND. This only reports a problem when all three status fields are non-zero at the same time. A normal target check condition, for example, has masked_status set while host_status and driver_status may both be zero, so the request is incorrectly reported as clean. Use the same condition as sg_new_read(), which sets SG_INFO_CHECK when any of the three status fields is non-zero. Cc: stable@vger.kernel.org Signed-off-by: Xu Rao Reviewed-by: Bart Van Assche Link: https://patch.msgid.link/54B60C19F7DB8889+20260707030845.970018-1-raoxu@uniontech.com Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman

scsi: hpsa: Fix DMA mapping leak on IOACCEL2 reset path

2026-07-24T13:49:13+00:00

commit e166bafc483e927150cb9b5f286c9191ea0df84e upstream. If phys_disk->in_reset is set, the function returns directly without undoing the resources acquired for the command. Add the missing error cleanup by unmapping the IOACCEL2 SG chain block when needed, unmapping the SCSI command, and dropping the outstanding IOACCEL command count before returning. Fixes: c5dfd106414f ("scsi: hpsa: correct device resets") Cc: stable@vger.kernel.org Signed-off-by: Haoxiang Li Acked-by: Don Brace Link: https://patch.msgid.link/20260622160028.1240496-1-haoxiang_li2024@163.com Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman

scsi: smartpqi: Use shost_to_hba() in pqi_scan_finished()

2026-07-24T13:49:11+00:00

commit 57db1307afb1f83d45f5ff53b93f8d040100d13e upstream. shost_to_hba() is used everywhere except to obtain pqi_ctrl_info from shosti, except in pqi_scan_finished(), where shost_priv() is used. This causes one pointer dereference to be missed, as shost->hostdata is a pointer in smartpqi. Fix it. Fixes: 6c223761eb54 ("smartpqi: initial commit of Microsemi smartpqi driver") Signed-off-by: Martin Wilck Reviewed-by: Don Brace Cc: Don Brace Cc: storagedev@microchip.com Cc: stable@vger.kernel.org Reviewed-by: Hannes Reinecke Reviewed-by: Hannes Reinecke Reviewed-by: Christoph Hellwig Link: https://patch.msgid.link/20260513174236.430465-2-mwilck@suse.com Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman

scsi: pm8001: Fix error code in non_fatal_log_show()

2026-07-24T13:48:58+00:00

[ Upstream commit 1b6f03b7ae9ee27054c55bb55a69d05555a78516 ] The non_fatal_log_show() function is supposed to return negative error codes on failure. But because the error codes are saved in a u32 and then cast to signed long, they end up being high positive values instead of negative. Remove the intermediary u32 variable to fix this bug. Fixes: dba2cc03b9db ("scsi: pm80xx: sysfs attribute for non fatal dump") Signed-off-by: Dan Carpenter Acked-by: Jack Wang Link: https://patch.msgid.link/ahs-bEsBJH0KhnsX@stanley.mountain Signed-off-by: Martin K. Petersen Signed-off-by: Sasha Levin

scsi: Revert "scsi: Fix sas_user_scan() to handle wildcard and multi-channel scans"

2026-07-24T13:48:58+00:00

[ Upstream commit 8c292e89bd831c8a13e92f3429ef66bbe0b83677 ] This reverts commit 37c4e72b0651e7697eb338cd1fb09feef472cc1a. Said commit causes excessive resource usage and even system freeze with some controllers, e.g. smartpqi and hisi_sas. The justification provided by the patch authors [1] was supporting a special mode of the mpi3mr and mpt3sas, so-called "Tri-mode", in which NVMe drives are exposed as SCSI devices on a separate channel. While that's useful for these drivers, it seems wrong to cause major breakage for other drivers for the sake of this feature. [1] https://lore.kernel.org/linux-scsi/CAFdVvOwjy+2ORJ6uJkspiLTPF05481U7gcS4QohFOFGPqAs8ig@mail.gmail.com/ Fixes: 37c4e72b0651 ("scsi: Fix sas_user_scan() to handle wildcard and multi-channel scans") Signed-off-by: Martin Wilck Cc: Don Brace Cc: storagedev@microchip.com Cc: Ranjan Kumar Cc: Sathya Prakash Veerichetty Cc: Kashyap Desai Cc: Sumit Saxena Cc: mpi3mr-linuxdrv.pdl@broadcom.com Cc: MPT-FusionLinux.pdl@broadcom.com Cc: Yihang Li Reviewed-by: Christoph Hellwig Link: https://patch.msgid.link/20260513174236.430465-3-mwilck@suse.com Signed-off-by: Martin K. Petersen Signed-off-by: Sasha Levin

use less confusing names for iov_iter direction initializers

2026-06-19T11:21:45+00:00

[ Upstream commit de4eda9de2d957ef2d6a8365a01e26a435e958cb ] READ/WRITE proved to be actively confusing - the meanings are "data destination, as used with read(2)" and "data source, as used with write(2)", but people keep interpreting those as "we read data from it" and "we write data to it", i.e. exactly the wrong way. Call them ITER_DEST and ITER_SOURCE - at least that is harder to misinterpret... Signed-off-by: Al Viro Stable-dep-of: a4f0b001782b ("vsock/virtio: reset connection on receiving queue overflow") Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

scsi: fcoe: Reject FIP descriptors with zero fip_dlen in CVL walker

2026-06-19T11:21:32+00:00

commit 9eed1bd59937e6828b00d2f2dfef631d964f3636 upstream. drivers/scsi/fcoe/fcoe_ctlr.c::fcoe_ctlr_recv_clr_vlink() advanced the descriptor cursor by an attacker-supplied fip_dlen without ever requiring dlen >= sizeof(struct fip_desc) in the default branch. The named descriptor cases (FIP_DT_MAC, FIP_DT_NAME, FIP_DT_VN_ID) checked their per-type minimum lengths, but a FIP_DT_NON_CRITICAL descriptor (fip_dtype >= 128, which the standard requires receivers to silently ignore) skipped that check entirely. An unauthenticated L2 peer on the FCoE control VLAN could hang fcoe_ctlr_recv_work on an fcoe, qedf, or bnx2fc initiator indefinitely by emitting one FIP CVL frame whose single descriptor had fip_dtype == FIP_DT_NON_CRITICAL and fip_dlen == 0: the cursor advanced zero bytes per iteration and the loop condition rlen >= sizeof(*desc) stayed true forever, blocking every subsequent FIP frame on that controller. Tighten the outer dlen guard to also reject dlen < sizeof(struct fip_desc), so a malformed descriptor whose length cannot even cover the descriptor header is rejected before the switch. This is the same lower-bound the named cases already apply and is the minimum scope that closes the loop. Fixes: 97c8389d54b9 ("[SCSI] fcoe, libfcoe: Add support for FIP. FCoE discovery and keep-alive.") Cc: stable@vger.kernel.org Assisted-by: Claude:claude-opus-4-7 Signed-off-by: Michael Bommarito Reviewed-by: Hannes Reinecke Link: https://patch.msgid.link/20260518144307.2820961-1-michael.bommarito@gmail.com Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman

scsi: isci: Fix use-after-free in device removal path

2026-06-01T15:29:52+00:00

commit b52a8d52c3125ec9a93106ed816582368de34426 upstream. The ISCI completion tasklet is initialized in isci_host_alloc() (drivers/scsi/isci/init.c:496) and scheduled from both MSI-X and legacy interrupt handlers (drivers/scsi/isci/host.c:223,613). isci_host_deinit() stops the controller and waits for stop completion, but it never kills completion_tasklet before teardown continues. A top-of-function tasklet_kill() is not sufficient here: interrupts are only disabled when isci_host_stop_complete() runs, so until wait_for_stop() returns the IRQ handlers can still requeue the tasklet. The tasklet callback also re-enables interrupts after draining completions, so killing the tasklet before the source is quiesced leaves the same race open. Once wait_for_stop() returns, no further IRQ-driven scheduling can occur. Kill completion_tasklet there so teardown cannot race a queued tasklet running on a dead ihost. On remove or unload, the stale callback can otherwise dereference ihost and touch ihost->smu_registers after the host lifetime ends. A UML + KASAN analogue reproduced the failure class both with no tasklet_kill() and with tasklet_kill() placed before source quiesce, and stayed clean once the kill happened after quiescing the scheduling source. This mirrors commit f6ab594672d4 ("scsi: aic94xx: fix use-after-free in device removal path"), but ISCI needs the kill after wait_for_stop(). Fixes: 6f231dda6808 ("isci: Intel(R) C600 Series Chipset Storage Control Unit Driver") Cc: stable@vger.kernel.org Assisted-by: Claude:claude-opus-4-7 Assisted-by: Codex:gpt-5-4 Signed-off-by: Michael Bommarito Link: https://patch.msgid.link/20260419210420.2134639-1-michael.bommarito@gmail.com Signed-off-by: Martin K. Petersen Signed-off-by: Greg Kroah-Hartman

cdrom, scsi: sr: propagate read-only status to block layer via set_disk_ro()

2026-06-01T15:29:43+00:00

[ Upstream commit 0898a817621a2f0cddca8122d9b974003fe5036d ] The cdrom core never calls set_disk_ro() for a registered device, so BLKROGET on a CD-ROM device always returns 0 (writable), even when the drive has no write capabilities and writes will inevitably fail. This causes problems for userspace that relies on BLKROGET to determine whether a block device is read-only. For example, systemd's loop device setup uses BLKROGET to decide whether to create a loop device with LO_FLAGS_READ_ONLY. Without the read-only flag, writes pass through the loop device to the CD-ROM and fail with I/O errors. systemd-fsck similarly checks BLKROGET to decide whether to run fsck in no-repair mode (-n). The write-capability bits in cdi->mask come from two different sources: CDC_DVD_RAM and CDC_CD_RW are populated by the driver from the MODE SENSE capabilities page (page 0x2A) before register_cdrom() is called, while CDC_MRW_W and CDC_RAM require the MMC GET CONFIGURATION command and were only probed by cdrom_open_write() at device open time. This meant that any attempt to compute the writable state from the full mask at probe time was incorrect, because the GET CONFIGURATION bits were still unset (and cdi->mask is initialized such that capabilities are assumed present). Fix this by factoring the GET CONFIGURATION probing out of cdrom_open_write() into a new exported helper, cdrom_probe_write_features(), and having sr call it from sr_probe() right after get_capabilities() has populated the MODE SENSE bits. register_cdrom() then calls set_disk_ro() based on the full write-capability mask (CDC_DVD_RAM | CDC_MRW_W | CDC_RAM | CDC_CD_RW) so the block layer reflects the drive's actual write support. The feature queries used (CDF_MRW and CDF_RWRT via GET CONFIGURATION with RT=00) report drive-level capabilities that are persistent across media, so a single probe before register_cdrom() is sufficient and the redundant probe at open time is dropped. With set_disk_ro() now accurate, the long-vestigial cd->writeable flag in sr can go: get_capabilities() used to set cd->writeable based on the same four mask bits, but because CDC_MRW_W and CDC_RAM default to "capability present" in cdi->mask and aren't touched by MODE SENSE, the condition that gated cd->writeable was always true, making it unconditionally 1. Replace the corresponding gate in sr_init_command() with get_disk_ro(cd->disk), which turns a previously no-op check into a real one and also catches kernel-internal bio writers that bypass blkdev_write_iter()'s bdev_read_only() check. The sd driver (SCSI disks) does not have this problem because it checks the MODE SENSE Write Protect bit and calls set_disk_ro() accordingly. The sr driver cannot use the same approach because the MMC specification does not define the WP bit in the MODE SENSE device-specific parameter byte for CD-ROM devices. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Daan De Meyer Reviewed-by: Phillip Potter Reviewed-by: Martin K. Petersen Signed-off-by: Phillip Potter Link: https://patch.msgid.link/20260427210139.1400-2-phil@philpotter.co.uk Signed-off-by: Jens Axboe Signed-off-by: Sasha Levin

scsi: sr: Add memory allocation failure handling for get_capabilities()

2026-06-01T15:29:43+00:00

[ Upstream commit ebc95c790653508ad7e031cfb9de5d0fa39135e2 ] The function get_capabilities() has the possibility of failing to allocate the transfer buffer but it does not currently handle this. This may lead to exceptions when accessing the buffer. Add error handling when memory allocation fails. Link: https://lore.kernel.org/r/20220427025647.298358-1-lienze@kylinos.cn Signed-off-by: Enze Li Signed-off-by: Martin K. Petersen Stable-dep-of: 0898a817621a ("cdrom, scsi: sr: propagate read-only status to block layer via set_disk_ro()") Signed-off-by: Sasha Levin