kernel/linux.git/drivers/s390/net, branch v4.4.235

s390/qeth: don't process empty bridge port events

2020-08-21T08:53:02+00:00

[ Upstream commit 02472e28b9a45471c6d8729ff2c7422baa9be46a ] Discard events that don't contain any entries. This shouldn't happen, but subsequent code relies on being able to use entry 0. So better be safe than accessing garbage. Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control") Signed-off-by: Julian Wiedmann Reviewed-by: Alexandra Winter Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

s390/qeth: invoke softirqs after napi_schedule()

2019-11-25T14:53:59+00:00

[ Upstream commit 4d19db777a2f32c9b76f6fd517ed8960576cb43e ] Calling napi_schedule() from process context does not ensure that the NET_RX softirq is run in a timely fashion. So trigger it manually. This is no big issue with current code. A call to ndo_open() is usually followed by a ndo_set_rx_mode() call, and for qeth this contains a spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out early. Nevertheless it's best to not depend on this behaviour, and just fix the issue at its source like all other drivers do. For instance see commit 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule"). Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

s390/qeth: fix VLAN attribute in bridge_hostnotify udev event

2019-07-10T07:56:32+00:00

[ Upstream commit 335726195e460cb6b3f795b695bfd31f0ea70ef0 ] Enabling sysfs attribute bridge_hostnotify triggers a series of udev events for the MAC addresses of all currently connected peers. In case no VLAN is set for a peer, the device reports the corresponding MAC addresses with VLAN ID 4096. This currently results in attribute VLAN=4096 for all non-VLAN interfaces in the initial series of events after host-notify is enabled. Instead, no VLAN attribute should be reported in the udev event for non-VLAN interfaces. Only the initial events face this issue. For dynamic changes that are reported later, the device uses a validity flag. This also changes the code so that it now sets the VLAN attribute for MAC addresses with VID 0. On Linux, no qeth interface will ever be registered with VID 0: Linux kernel registers VID 0 on all network interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0. Peers with other OSs could register MACs with VID 0. Fixes: 9f48b9db9a22 ("qeth: bridgeport support - address notifications") Signed-off-by: Alexandra Winter Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

s390: ctcm: fix ctcm_new_device error return code

2019-05-16T17:45:06+00:00

[ Upstream commit 27b141fc234a3670d21bd742c35d7205d03cbb3a ] clang points out that the return code from this function is undefined for one of the error paths: ../drivers/s390/net/ctcm_main.c:1595:7: warning: variable 'result' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized] if (priv->channel[direction] == NULL) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ../drivers/s390/net/ctcm_main.c:1638:9: note: uninitialized use occurs here return result; ^~~~~~ ../drivers/s390/net/ctcm_main.c:1595:3: note: remove the 'if' if its condition is always false if (priv->channel[direction] == NULL) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ../drivers/s390/net/ctcm_main.c:1539:12: note: initialize the variable 'result' to silence this warning int result; ^ Make it return -ENODEV here, as in the related failure cases. gcc has a known bug in underreporting some of these warnings when it has already eliminated the assignment of the return code based on some earlier optimization step. Reviewed-by: Nathan Chancellor Signed-off-by: Arnd Bergmann Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

s390/qeth: fix use-after-free in error path

2019-03-23T07:44:27+00:00

[ Upstream commit afa0c5904ba16d59b0454f7ee4c807dae350f432 ] The error path in qeth_alloc_qdio_buffers() that takes care of cleaning up the Output Queues is buggy. It first frees the queue, but then calls qeth_clear_outq_buffers() with that very queue struct. Make the call to qeth_clear_outq_buffers() part of the free action (in the correct order), and while at it fix the naming of the helper. Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann Reviewed-by: Alexandra Winter Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

s390/qeth: fix length check in SNMP processing

2018-12-13T08:21:26+00:00

[ Upstream commit 9a764c1e59684c0358e16ccaafd870629f2cfe67 ] The response for a SNMP request can consist of multiple parts, which the cmd callback stages into a kernel buffer until all parts have been received. If the callback detects that the staging buffer provides insufficient space, it bails out with error. This processing is buggy for the first part of the response - while it initially checks for a length of 'data_len', it later copies an additional amount of 'offsetof(struct qeth_snmp_cmd, data)' bytes. Fix the calculation of 'data_len' for the first part of the response. This also nicely cleans up the memcpy code. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Julian Wiedmann Reviewed-by: Ursula Braun Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

s390/qeth: don't dump past end of unknown HW header

2018-10-10T06:52:12+00:00

[ Upstream commit 0ac1487c4b2de383b91ecad1be561b8f7a2c15f4 ] For inbound data with an unsupported HW header format, only dump the actual HW header. We have no idea how much payload follows it, and what it contains. Worst case, we dump past the end of the Inbound Buffer and access whatever is located next in memory. Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

s390/qeth: reset layer2 attribute on layer switch

2018-09-26T06:35:06+00:00

[ Upstream commit 70551dc46ffa3555a0b5f3545b0cd87ab67fd002 ] After the subdriver's remove() routine has completed, the card's layer mode is undetermined again. Reflect this in the layer2 field. If qeth_dev_layer2_store() hits an error after remove() was called, the card _always_ requires a setup(), even if the previous layer mode is requested again. But qeth_dev_layer2_store() bails out early if the requested layer mode still matches the current one. So unless we reset the layer2 field, re-probing the card back to its previous mode is currently not possible. Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

s390/qeth: fix race in used-buffer accounting

2018-09-26T06:35:06+00:00

[ Upstream commit a702349a4099cd5a7bab0904689d8e0bf8dcd622 ] By updating q->used_buffers only _after_ do_QDIO() has completed, there is a potential race against the buffer's TX completion. In the unlikely case that the TX completion path wins, qeth_qdio_output_handler() would decrement the counter before qeth_flush_buffers() even incremented it. Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

s390/qeth: on channel error, reject further cmd requests

2018-03-31T16:12:34+00:00

[ Upstream commit a6c3d93963e4b333c764fde69802c3ea9eaa9d5c ] When the IRQ handler determines that one of the cmd IO channels has failed and schedules recovery, block any further cmd requests from being submitted. The request would inevitably stall, and prevent the recovery from making progress until the request times out. This sort of error was observed after Live Guest Relocation, where the pending IO on the READ channel intentionally gets terminated to kick-start recovery. Simultaneously the guest executed SIOCETHTOOL, triggering qeth to issue a QUERY CARD INFO command. The command then stalled in the inoperabel WRITE channel. Signed-off-by: Julian Wiedmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman