kernel/linux.git/drivers/regulator, branch v6.12.80

regulator: pca9450: Correct interrupt type

2026-03-25T10:08:29+00:00

[ Upstream commit 5d0efaf47ee90ac60efae790acee3a3ed99ebf80 ] Kernel warning on i.MX8MP-EVK when doing module test: irq: type mismatch, failed to map hwirq-3 for gpio@30200000! Per PCA945[X] specification: The IRQ_B pin is pulled low when any unmasked interrupt bit status is changed and it is released high once application processor read INT1 register. So the interrupt should be configured as IRQF_TRIGGER_LOW, not IRQF_TRIGGER_FALLING. Fixes: 0935ff5f1f0a4 ("regulator: pca9450: add pca9450 pmic driver") Signed-off-by: Peng Fan Link: https://patch.msgid.link/20260310-pca9450-irq-v1-1-36adf52c2c55@nxp.com Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: core: move supply check earlier in set_machine_constraints()

2026-03-04T12:19:54+00:00

[ Upstream commit 86a8eeb0e913f4b6a55dabba5122098d4e805e55 ] Since commit 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators"), set_machine_constraints() can return -EPROBE_DEFER very late, after it has done a lot of work and configuration of the regulator. This means that configuration will happen multiple times for no benefit in that case. Furthermore, this can lead to timing-dependent voltage glitches as mentioned e.g. in commit 8a866d527ac0 ("regulator: core: Resolve supply name earlier to prevent double-init"). We can know that it's going to fail very early, in particular before going through the complete regulator configuration by moving some code around a little. Do so to avoid re-configuring the regulator multiple times, also avoiding the voltage glitches if we can. Fixes: 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators") Signed-off-by: André Draszik Link: https://patch.msgid.link/20260109-regulators-defer-v2-3-1a25dc968e60@linaro.org Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: fixed: Rely on the core freeing the enable GPIO

2025-12-18T12:55:19+00:00

[ Upstream commit 79a45ddcdbba330f5139c7c7ff7042d69cf147b2 ] In order to simplify ownership rules for enable GPIOs supplied by drivers regulator_register() always takes ownership of them, even if it ends up failing for some other reason. We therefore should not free the GPIO if registration fails but just let the core worry about things. Fixes: 636f4618b1cd (regulator: fixed: fix GPIO descriptor leak on register failure) Reported-by: Diederik de Haas Closes: https://lore.kernel.org/r/DEPEYUF5BRGY.UKFBWRRE8HNP@cknow-tech.com Tested-by: Diederik de Haas Signed-off-by: Mark Brown Link: https://patch.msgid.link/20251204-regulator-fixed-fix-gpiod-leak-v1-1-48efea5b82c2@kernel.org Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: core: Protect regulator_supply_alias_list with regulator_list_mutex

2025-12-18T12:55:11+00:00

[ Upstream commit 0cc15a10c3b4ab14cd71b779fd5c9ca0cb2bc30d ] regulator_supply_alias_list was accessed without any locking in regulator_supply_alias(), regulator_register_supply_alias(), and regulator_unregister_supply_alias(). Concurrent registration, unregistration and lookups can race, leading to: 1 use-after-free if an alias entry is removed while being read, 2 duplicate entries when two threads register the same alias, 3 inconsistent alias mappings observed by consumers. Protect all traversals, insertions and deletions on regulator_supply_alias_list with the existing regulator_list_mutex. Fixes: a06ccd9c3785f ("regulator: core: Add ability to create a lookup alias for supply") Signed-off-by: sparkhuang Reviewed-by: Charles Keepax Link: https://patch.msgid.link/20251127025716.5440-1-huangshaobo3@xiaomi.com Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: core: disable supply if enabling main regulator fails

2025-12-18T12:54:55+00:00

[ Upstream commit fb1ebb10468da414d57153ddebaab29c38ef1a78 ] For 'always-on' and 'boot-on' regulators, the set_machine_constraints() may enable supply before enabling the main regulator, however if the latter fails, the function returns with an error but the supply remains enabled. When this happens, the regulator_register() function continues on the error path where it puts the supply regulator. Since enabling the supply is not balanced with a disable call, a warning similar to the following gets issued from _regulator_put(): [ 1.603889] WARNING: CPU: 2 PID: 44 at _regulator_put+0x8c/0xa0 [ 1.603908] Modules linked in: [ 1.603926] CPU: 2 UID: 0 PID: 44 Comm: kworker/u16:3 Not tainted 6.18.0-rc4 #0 NONE [ 1.603938] Hardware name: Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7 (DT) [ 1.603945] Workqueue: async async_run_entry_fn [ 1.603958] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1.603967] pc : _regulator_put+0x8c/0xa0 [ 1.603976] lr : _regulator_put+0x7c/0xa0 ... [ 1.604140] Call trace: [ 1.604145] _regulator_put+0x8c/0xa0 (P) [ 1.604156] regulator_register+0x2ec/0xbf0 [ 1.604166] devm_regulator_register+0x60/0xb0 [ 1.604178] rpm_reg_probe+0x120/0x208 [ 1.604187] platform_probe+0x64/0xa8 ... In order to avoid this, change the set_machine_constraints() function to disable the supply if enabling the main regulator fails. Fixes: 05f224ca6693 ("regulator: core: Clean enabling always-on regulators + their supplies") Signed-off-by: Gabor Juhos Link: https://patch.msgid.link/20251107-regulator-disable-supply-v1-1-c95f0536f1b5@gmail.com Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: fixed: fix GPIO descriptor leak on register failure

2025-11-24T09:35:53+00:00

[ Upstream commit 636f4618b1cd96f6b5a2b8c7c4f665c8533ecf13 ] In the commit referenced by the Fixes tag, devm_gpiod_get_optional() was replaced by manual GPIO management, relying on the regulator core to release the GPIO descriptor. However, this approach does not account for the error path: when regulator registration fails, the core never takes over the GPIO, resulting in a resource leak. Add gpiod_put() before returning on regulator registration failure. Fixes: 5e6f3ae5c13b ("regulator: fixed: Let core handle GPIO descriptor") Signed-off-by: Haotian Zhang Link: https://patch.msgid.link/20251028172828.625-1-vulab@iscas.ac.cn Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: scmi: Use int type to store negative error codes

2025-10-15T09:59:57+00:00

[ Upstream commit 9d35d068fb138160709e04e3ee97fe29a6f8615b ] Change the 'ret' variable from u32 to int to store negative error codes or zero returned by of_property_read_u32(). Storing the negative error codes in unsigned type, doesn't cause an issue at runtime but it's ugly as pants. Additionally, assigning negative error codes to unsigned type may trigger a GCC warning when the -Wsign-conversion flag is enabled. No effect on runtime. Signed-off-by: Qianfeng Rong Reviewed-by: Sudeep Holla Fixes: 0fbeae70ee7c ("regulator: add SCMI driver") Link: https://patch.msgid.link/20250829101411.625214-1-rongqianfeng@vivo.com Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: sy7636a: fix lifecycle of power good gpio

2025-09-19T14:35:50+00:00

[ Upstream commit c05d0b32eebadc8be6e53196e99c64cf2bed1d99 ] Attach the power good gpio to the regulator device devres instead of the parent device to fix problems if probe is run multiple times (rmmod/insmod or some deferral). Fixes: 8c485bedfb785 ("regulator: sy7636a: Initial commit") Signed-off-by: Andreas Kemnade Reviewed-by: Alistair Francis Reviewed-by: Peng Fan Message-ID: <20250906-sy7636-rsrc-v1-2-e2886a9763a7@kernel.org> Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: core: fix NULL dereference on unbind due to stale coupling data

2025-08-01T08:48:39+00:00

[ Upstream commit ca46946a482238b0cdea459fb82fc837fb36260e ] Failing to reset coupling_desc.n_coupled after freeing coupled_rdevs can lead to NULL pointer dereference when regulators are accessed post-unbind. This can happen during runtime PM or other regulator operations that rely on coupling metadata. For example, on ridesx4, unbinding the 'reg-dummy' platform device triggers a panic in regulator_lock_recursive() due to stale coupling state. Ensure n_coupled is set to 0 to prevent access to invalid pointers. Signed-off-by: Alessandro Carminati Link: https://patch.msgid.link/20250626083809.314842-1-acarmina@redhat.com Signed-off-by: Mark Brown Signed-off-by: Sasha Levin

regulator: fan53555: add enable_time support and soft-start times

2025-07-10T14:05:07+00:00

[ Upstream commit 8acfb165a492251a08a22a4fa6497a131e8c2609 ] The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown Signed-off-by: Sasha Levin