kernel/linux.git/drivers/pwm, branch v4.11.5

pwm: rockchip: State of PWM clock should synchronize with PWM enabled state

2017-04-06T13:08:52+00:00

If the PWM was not enabled at U-Boot loader, PWM could not work for clock always disabled at PWM driver. The PWM clock is enabled at beginning of pwm_apply(), but disabled at end of pwm_apply(). If the PWM was enabled at U-Boot loader, PWM clock is always enabled unless closed by ATF. The pwm-backlight might turn off the power at early suspend, should disable PWM clock for saving power consume. It is important to provide opportunity to enable/disable clock at PWM driver, the PWM consumer should ensure correct order to call PWM enable and disable, and PWM driver ensure state of PWM clock synchronized with PWM enabled state. Fixes: 2bf1c98aa5a4 ("pwm: rockchip: Add support for atomic update") Cc: stable@vger.kernel.org Signed-off-by: David Wu Reviewed-by: Boris Brezillon Signed-off-by: Thierry Reding

pwm: lpss: Set enable-bit before waiting for update-bit to go low

2017-04-06T12:48:14+00:00

At least on cherrytrail, the update bit will never go low when the enabled bit is not set. This causes the backlight on my cube iwork8 air tablet to never turn on again after being turned off because in the pwm_lpss_apply enable path pwm_lpss_update will fail causing an error exit and the enable-bit to never get set. Any following pwm_lpss_apply calls will fail the pwm_lpss_is_updating check. Since the docs say that the update bit should be set before the enable-bit, split pwm_lpss_update into setting the update-bit and pwm_lpss_wait_for_update, and move the pwm_lpss_wait_for_update call in the enable path to after setting the enable-bit. Fixes: 10d56a4 ("pwm: lpss: Avoid reconfiguring while UPDATE bit...") Cc: Ilkka Koskinen Signed-off-by: Hans de Goede Signed-off-by: Andy Shevchenko Tested-by: Hans de Goede Signed-off-by: Thierry Reding

pwm: lpss: Split Tangier configuration

2017-04-06T12:47:30+00:00

As a preparation for special treatment for Broxton we split Tangier configuration. Fixes: b89b4b7a3d0a ("pwm: lpss: pci: Enable PWM module on Intel Edison") Signed-off-by: Andy Shevchenko Tested-by: Hans de Goede Signed-off-by: Thierry Reding

Merge tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

2017-03-01T17:46:02+00:00

Pull pwm updates from Thierry Reding: "This set contains mostly fixes to existing drivers as well as cleanup of code that's not been in active use for a while" * tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (27 commits) acpi: lpss: call pwm_add_table() for BSW PWM device pwm: Try to load modules during pwm_get() pwm: Don't hold pwm_lookup_lock longer than necessary pwm: Make the PWM_POLARITY flag in DTB optional pwm: Print error messages with pr_err() instead of pr_debug() pwm: imx: Add polarity inversion support to i.MX's PWMv2 pwm: imx: doc: Update imx-pwm.txt documentation entry pwm: imx: Remove redundant i.MX PWMv2 code pwm: imx: Provide atomic PWM support for i.MX PWMv2 pwm: imx: Move PWMv2 wait for fifo slot code to a separate function pwm: imx: Move PWMv2 software reset code to a separate function pwm: imx: Rewrite v1 code to facilitate switch to atomic PWM pwm: imx: Add separate set of PWM ops for v1 and v2 pwm: imx: Remove ipg clock and enable per clock when required pwm: lpss: Add Intel Gemini Lake PCI ID pwm: lpss: Do not export board infos for different PWM types pwm: lpss: Avoid reconfiguring while UPDATE bit is still enabled pwm: lpss: Switch to new atomic API pwm: lpss: Allow duty cycle to be 0 pwm: lpss: Avoid potential overflow of base_unit ...

Merge branch 'for-4.11/drivers' into for-next

2017-02-10T14:15:56+00:00

pwm: Try to load modules during pwm_get()

2017-01-30T08:36:42+00:00

Add a module name string to the pwm_lookup struct and if specified try to load the module using request_module() if pwmchip_find_by_name() is unable to find the PWM chip. This is a last resort to work around drivers that can't - and can't be made to - deal with deferred probe. Signed-off-by: Hans de Goede [thierry.reding@gmail.com: rename new macro, reword commit message] [thierry.reding@gmail.com: add comment explaining use-case] Signed-off-by: Thierry Reding

pwm: Don't hold pwm_lookup_lock longer than necessary

2017-01-30T08:19:26+00:00

There is no need to hold pwm_lookup_lock after we're done with looping over pwm_lookup_list, so release it earlier. Signed-off-by: Hans de Goede Signed-off-by: Thierry Reding

pwm: Make the PWM_POLARITY flag in DTB optional

2017-01-30T08:13:34+00:00

Change the PWM chip driver registration so that a chip driver that supports polarity inversion can still be used with DTBs that don't provide the polarity flag as part of the specifier. This is done to provide polarity inversion support for the pwm-imx driver without having to modify all existing DTS files. Signed-off-by: Lothar Wassmann Signed-off-by: Bhuvanchandra DV Suggested-by: Sascha Hauer Signed-off-by: Lukasz Majewski Reviewed-by: Boris Brezillon Signed-off-by: Thierry Reding

pwm: Print error messages with pr_err() instead of pr_debug()

2017-01-30T08:13:30+00:00

Make the messages that are printed in case of fatal errors actually visible to the user without having to recompile the driver with debugging enabled. Signed-off-by: Lothar Waßmann Signed-off-by: Bhuvanchandra DV Reviewed-by: Boris Brezillon Signed-off-by: Thierry Reding

pwm: imx: Add polarity inversion support to i.MX's PWMv2

2017-01-30T08:13:07+00:00

With this patch the polarity settings for i.MX's PWMv2 is now supported on top of atomic PWM setting Signed-off-by: Bhuvanchandra DV Signed-off-by: Lukasz Majewski Reviewed-by: Boris Brezillon Signed-off-by: Thierry Reding