kernel/linux.git/drivers/power/reset/Makefile, branch v6.12.80

power: reset: Add a driver for the ep93xx reset

2024-09-12T14:33:10+00:00

Implement the reset behaviour of the various EP93xx SoCS in drivers/power/reset. It used to be located in arch/arm/mach-ep93xx. Signed-off-by: Nikita Shubin Tested-by: Alexander Sverdlin Acked-by: Sebastian Reichel Acked-by: Vinod Koul Signed-off-by: Arnd Bergmann

power: reset: oxnas-restart: remove obsolete restart driver

2023-07-19T22:29:18+00:00

Due to lack of maintenance and stall of development for a few years now, and since no new features will ever be added upstream, remove support for OX810 and OX820 restart feature. Acked-by: Linus Walleij Acked-by: Arnd Bergmann Acked-by: Daniel Golle Acked-by: Andy Shevchenko Signed-off-by: Neil Armstrong Signed-off-by: Sebastian Reichel

power: reset: add Odroid Go Ultra poweroff driver

2023-02-14T22:02:39+00:00

The Hardkernel Odroid Go Ultra poweroff scheme requires requesting a poweroff to its two PMICs in order, this represents the poweroff scheme needed to complete a clean poweroff of the system. This implement this scheme by implementing a self registering driver to permit using probe defer until both pmics are finally probed. Signed-off-by: Neil Armstrong Signed-off-by: Sebastian Reichel

power: reset: pwr-mlxbf: add BlueField SoC power control driver

2022-06-17T15:05:28+00:00

This driver supports handling 2 BlueField power states controlled by GPIO interrupts: 1) chip reset and 2) low power mode Signed-off-by: Asmaa Mnebhi Signed-off-by: Sebastian Reichel

power: reset: Add TPS65086 restart driver

2021-08-16T12:48:51+00:00

The only way to reset the BeagleV Starlight v0.9 board[1] properly is to tell the PMIC to reset itself which will then assert the external reset lines of the SoC, USB hub and ethernet phy. This adds a driver to register a reset handler to do just that. [1] https://github.com/beagleboard/beaglev-starlight Signed-off-by: Emil Renner Berthing Signed-off-by: Sebastian Reichel

power: reset: replace curly brackets in Makefile

2021-03-23T15:25:56+00:00

Normal parentheses should be used when referring to config variables in Makefile. Replace the accidentally introduced curly brackets by regular parentheses. Fixes: a7f79f99541ef ("power: reset: add driver for LinkStation power off") Acked-by: Daniel González Cabanelas Signed-off-by: Daniel Golle Signed-off-by: Sebastian Reichel

power/reset: remove zte zx driver

2021-01-25T00:00:06+00:00

The zte zx platform is getting removed, so this driver is no longer needed. Cc: Jun Nie Cc: Shawn Guo Signed-off-by: Arnd Bergmann Signed-off-by: Sebastian Reichel

power: reset: Add poweroff driver for ATC260x PMICs

2021-01-13T21:17:23+00:00

This driver provides poweroff and reboot support for a system through the ATC2603C and ATC2609A chip variants of the Actions Semi ATC260x family of PMICs. Signed-off-by: Cristian Ciocaltea Signed-off-by: Sebastian Reichel

power: reset: new driver regulator-poweroff

2020-12-12T23:14:15+00:00

This driver registers a pm_power_off function to turn off the board by force-disabling a devicetree-defined regulator. Signed-off-by: Michael Klein Signed-off-by: Sebastian Reichel

power: reset: add driver for LinkStation power off

2020-07-27T23:49:32+00:00

Some Buffalo LinkStations perform the power off operation, at restart time, depending on the state of an output pin (LED2/INTn) at the ethernet PHY. This pin is also used to wake the machine when a WoL packet is received by the PHY. The driver is required by the Buffalo LinkStation LS421DE (ARM MVEBU), and other models. Without it, the board remains forever halted if a power off command is executed, unless the PSU is disconnected and connected again. Add the driver to provide the power off function and also make the WoL feature to be available. Signed-off-by: Daniel González Cabanelas Signed-off-by: Sebastian Reichel