kernel/linux.git/drivers/pinctrl, branch v4.4.235

pinctrl-single: fix pcs_parse_pinconf() return value

2020-08-21T08:53:03+00:00

[ Upstream commit f46fe79ff1b65692a65266a5bec6dbe2bf7fc70f ] This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no pinctrl_map is added. The current behavior is to return 0 when !PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry() incorrectly assumes that a map was added and sets num_maps = 2. Analysis: ========= The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf() if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf() returns 0 to indicate there was no error and num_maps is then set to 2: 980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs, 981 struct device_node *np, 982 struct pinctrl_map **map, 983 unsigned *num_maps, 984 const char **pgnames) 985 { 1053 (*map)->type = PIN_MAP_TYPE_MUX_GROUP; 1054 (*map)->data.mux.group = np->name; 1055 (*map)->data.mux.function = np->name; 1056 1057 if (PCS_HAS_PINCONF && function) { 1058 res = pcs_parse_pinconf(pcs, np, function, map); 1059 if (res) 1060 goto free_pingroups; 1061 *num_maps = 2; 1062 } else { 1063 *num_maps = 1; 1064 } However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or !nconfs. I believe these conditions should indicate that no map was added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry() will set num_maps = 2 even though no maps were successfully added, as it does not reach "m++" on line 940: 895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np, 896 struct pcs_function *func, 897 struct pinctrl_map **map) 898 899 { 900 struct pinctrl_map *m = *map; 917 /* If pinconf isn't supported, don't parse properties in below. */ 918 if (!PCS_HAS_PINCONF) 919 return 0; 920 921 /* cacluate how much properties are supported in current node */ 922 for (i = 0; i < ARRAY_SIZE(prop2); i++) { 923 if (of_find_property(np, prop2[i].name, NULL)) 924 nconfs++; 925 } 926 for (i = 0; i < ARRAY_SIZE(prop4); i++) { 927 if (of_find_property(np, prop4[i].name, NULL)) 928 nconfs++; 929 } 930 if (!nconfs) 919 return 0; 932 933 func->conf = devm_kcalloc(pcs->dev, 934 nconfs, sizeof(struct pcs_conf_vals), 935 GFP_KERNEL); 936 if (!func->conf) 937 return -ENOMEM; 938 func->nconfs = nconfs; 939 conf = &(func->conf[0]); 940 m++; This situtation will cause a boot failure [0] on the BeagleBone Black (AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi has compatible = "pinconf-single" instead of "pinctrl-single". The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no map was added. Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps is set to 1 as it is valid for pinconf to be enabled and a given pin group to not any pinconf properties. [0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/ Fixes: 9dddb4df90d1 ("pinctrl: single: support generic pinconf") Signed-off-by: Drew Fustini Acked-by: Tony Lindgren Link: https://lore.kernel.org/r/20200608125143.GA2789203@x1 Signed-off-by: Linus Walleij Signed-off-by: Sasha Levin

pinctrl: amd: fix npins for uart0 in kerncz_groups

2020-07-31T14:43:11+00:00

[ Upstream commit 69339d083dfb7786b0e0b3fc19eaddcf11fabdfb ] uart0_pins is defined as: static const unsigned uart0_pins[] = {135, 136, 137, 138, 139}; which npins is wronly specified as 9 later { .name = "uart0", .pins = uart0_pins, .npins = 9, }, npins should be 5 instead of 9 according to the definition. Signed-off-by: Jacky Hu Link: https://lore.kernel.org/r/20200616015024.287683-1-hengqing.hu@gmail.com Signed-off-by: Linus Walleij Signed-off-by: Sasha Levin

pinctrl: samsung: Save/restore eint_mask over suspend for EINT_TYPE GPIOs

2020-06-20T08:23:24+00:00

commit f354157a7d184db430c1a564c506434e33b1bec5 upstream. Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers are saved and restored over a suspend/resume cycle. However, the EINT_MASK registers are not. On S5PV210 at the very least, these registers are not retained over suspend, leading to the interrupts remaining masked upon resume and therefore no interrupts being triggered for the device. There should be no effect on any SoCs that do retain these registers as theoretically we would just be re-writing what was already there. Fixes: 7ccbc60cd9c2 ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers") Cc: Signed-off-by: Jonathan Bakker Signed-off-by: Krzysztof Kozlowski Signed-off-by: Greg Kroah-Hartman

pinctrl: tegra: Correctly check the supported configuration

2020-05-10T08:26:34+00:00

commit b22ef2a0979f2b91cfeeabb086e4d665183a93a1 upstream. The pincontrol registers of Tegra chips has multiple filed per registers. There is two type of registers mux and drive. All configurations belongs to one of these registers. If any configurations are supported then _bit is set to bit position of these registers otherwise -1 to not support it. The member is defined as s32 _bit:6; So if config is not supported ifor given SoC then it is set to -1 in soc pinmmux table. In common driver code, to find out that given config is supported or not, it is checked as: s8 bit = _bit; if (bit > 31) { /* Not supported config */ } But in this case, bit is s8 and hence for non supporting it is -1. Correct the check as: if (bit < 0) { /* Not supported config */ } Fixes: e4c02dced975cb ("pinctrl: tegra: use signed bitfields for optional fields") Signed-off-by: Laxman Dewangan Acked-by: Stephen Warren Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman

pinctrl: bcm2835: Fix memory leak in error path

2020-05-10T08:26:14+00:00

commit 53653c6b91750debba6dc4503003c851257fd340 upstream. In case of an invalid pin value bcm2835_pctl_dt_node_to_map() would leak the pull configs of already assigned pins. So avoid this by calling the free map function in error case. Signed-off-by: Stefan Wahren Fixes: e1b2dc70cd5b ("pinctrl: add bcm2835 driver") Reviewed-by: Eric Anholt Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman

pinctrl: sh-pfc: sh7269: Fix CAN function GPIOs

2020-02-28T14:39:01+00:00

[ Upstream commit 02aeb2f21530c98fc3ca51028eda742a3fafbd9f ] pinmux_func_gpios[] contains a hole due to the missing function GPIO definition for the "CTX0&CTX1" signal, which is the logical "AND" of the first two CAN outputs. A closer look reveals other issues: - Some functionality is available on alternative pins, but the PINMUX_DATA() entries is using the wrong marks, - Several configurations are missing. Fix this by: - Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK, resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the corresponding enum IDs, - Adding all missing enum IDs and marks, - Use the right (*_PJ2x) variants for alternative pins, - Adding all missing configurations to pinmux_data[], - Adding all missing function GPIO definitions to pinmux_func_gpios[]. See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00: [1] Table 1.4 List of Pins [2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel (32 Mailboxes × 1 Channel), [3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as One Channel (96 Mailboxes × 1 Channel), [4] Table 48.3 Multiplexed Pins (Port B), [5] Table 48.4 Multiplexed Pins (Port C), [6] Table 48.10 Multiplexed Pins (Port J), [7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5). Signed-off-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be Signed-off-by: Sasha Levin

pinctrl: sh-pfc: sh7264: Fix CAN function GPIOs

2020-02-28T14:38:52+00:00

[ Upstream commit 55b1cb1f03ad5eea39897d0c74035e02deddcff2 ] pinmux_func_gpios[] contains a hole due to the missing function GPIO definition for the "CTX0&CTX1" signal, which is the logical "AND" of the two CAN outputs. Fix this by: - Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010 configures the combined "CTX0&CTX1" output signal, - Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures the shared "CRX0/CRX1" input signal, which is fed to both CAN inputs, - Adding the missing function GPIO definition for "CTX0&CTX1" to pinmux_func_gpios[], - Moving all CAN enums next to each other. See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00: [1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte Version), [2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte Version, [3] Table 1.4 List of Pins, [4] Figure 20.29 Connection Example when Using This Module as 1-Channel Module (64 Mailboxes x 1 Channel), [5] Table 32.10 Multiplexed Pins (Port J), [6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0). Note that the last 2 disagree about PJ2MD[2:0], which is probably the root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must be correct, and "CRx0&CRx1" in [6] must be wrong. Signed-off-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be Signed-off-by: Sasha Levin

pinctrl: sh-pfc: r8a7778: Fix duplicate SDSELF_B and SD1_CLK_B

2020-02-14T21:30:01+00:00

commit 805f635703b2562b5ddd822c62fc9124087e5dd5 upstream. The FN_SDSELF_B and FN_SD1_CLK_B enum IDs are used twice, which means one set of users must be wrong. Replace them by the correct enum IDs. Fixes: 87f8c988636db0d4 ("sh-pfc: Add r8a7778 pinmux support") Signed-off-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/20191218194812.12741-2-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman

pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups

2020-01-29T09:21:39+00:00

[ Upstream commit 0e6e448bdcf896d001a289a6112a704542d51516 ] There are two pin groups for the FSIC SPDIF signal, but the FSIC pin group array lists only one, and it refers to a nonexistent group. Fixes: 2ecd4154c906b7d6 ("sh-pfc: sh73a0: Add FSI pin groups and functions") Signed-off-by: Geert Uytterhoeven Reviewed-by: Simon Horman Signed-off-by: Sasha Levin

pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group

2020-01-29T09:21:39+00:00

[ Upstream commit a4b0350047f1b10207e25e72d7cd3f7826e93769 ] The entry for "scifb2_data_c" in the SCIFB2 pin group array contains a typo, thus the group cannot be selected. Fixes: 5088451962389924 ("pinctrl: sh-pfc: r8a7791 PFC support") Signed-off-by: Geert Uytterhoeven Reviewed-by: Simon Horman Signed-off-by: Sasha Levin