kernel/linux.git/drivers/pinctrl/bcm, branch linux-4.20.y

pinctrl: bcm2835: Use raw spinlock for RT compatibility

2019-02-12T19:02:04+00:00

[ Upstream commit 3c7b30f704b6f5e53eed6bf89cf2c8d1b38b02c0 ] The BCM2835 pinctrl driver acquires a spinlock in its ->irq_enable, ->irq_disable and ->irq_set_type callbacks. Spinlocks become sleeping locks with CONFIG_PREEMPT_RT_FULL=y, therefore invocation of one of the callbacks in atomic context may cause a hard lockup if at least two GPIO pins in the same bank are used as interrupts. The issue doesn't occur with just a single interrupt pin per bank because the lock is never contended. I'm experiencing such lockups with GPIO 8 and 28 used as level-triggered interrupts, i.e. with ->irq_disable being invoked on reception of every IRQ. The critical section protected by the spinlock is very small (one bitop and one RMW of an MMIO register), hence converting to a raw spinlock seems a better trade-off than converting the driver to threaded IRQ handling (which would increase latency to handle an interrupt). Cc: Mathias Duckeck Signed-off-by: Lukas Wunner Acked-by: Julia Cartwright Signed-off-by: Linus Walleij Signed-off-by: Sasha Levin

pinctrl: bcm: ns: Use uintptr_t for casting data

2018-10-12T09:14:59+00:00

Fix up a compiler error on 64bit architectures where pointers and integers differ in size. Suggested-by: Arnd Bergmann Signed-off-by: Rafał Miłecki Signed-off-by: Linus Walleij

pinctrl: bcm: add Northstar driver

2018-10-10T07:16:54+00:00

This driver provides support for Northstar mux controller. It differs from Northstar Plus one so a new binding and driver were needed. Signed-off-by: Rafał Miłecki Signed-off-by: Linus Walleij

pinctrl: nsp: Fix potential NULL dereference

2018-07-14T10:47:04+00:00

platform_get_resource() may fail and return NULL, so we should better check it's return value to avoid a NULL pointer dereference a bit later in the code. This is detected by Coccinelle semantic patch. @@ expression pdev, res, n, t, e, e1, e2; @@ res = platform_get_resource(pdev, t, n); + if (!res) + return -EINVAL; ... when != res == NULL e = devm_ioremap_nocache(e1, res->start, e2); Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC") Signed-off-by: Wei Yongjun Reviewed-by: Ray Jui Signed-off-by: Linus Walleij

pinctrl: nsp: off by ones in nsp_pinmux_enable()

2018-07-14T10:47:04+00:00

The > comparisons should be >= or else we read beyond the end of the pinctrl->functions[] array. Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC") Signed-off-by: Dan Carpenter Reviewed-by: Ray Jui Signed-off-by: Linus Walleij

treewide: kzalloc() -> kcalloc()

2018-06-12T23:19:22+00:00

The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook

pinctrl: bcm2835: Add support for output-low output-high properties

2018-05-16T12:01:37+00:00

Properties to set initial value of pin output buffer. This can be useful for configure hardware in overlay files, and in early boot for checking it states in QA sanity tests. Signed-off-by: Matheus Castello Reviewed-by: Eric Anholt Acked-by: Stefan Wahren Signed-off-by: Linus Walleij

pinctrl: bcm2835: Add support for generic pinctrl binding

2018-05-16T12:00:00+00:00

To keep driver up to date we add generic pinctrl binding support, which covers the features used in this driver and has additional node properties that this SoC has compatibility, so enabling future implementations of these properties without the need to create new node properties in the device trees. The logic of this change maintain the old brcm legacy binding support in order to keep the ABI stable. Signed-off-by: Matheus Castello Reviewed-by: Eric Anholt Acked-by: Stefan Wahren Signed-off-by: Linus Walleij

Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

2017-11-16T18:57:11+00:00

Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v4.15 kernel cycle: Core: - The pin control Kconfig entry PINCTRL is now turned into a menuconfig option. This obviously has the implication of making the subsystem menu visible in menuconfig. This is happening because of two things: (a) Intel have started to deploy and depend on pin controllers in a way that is affecting users directly. This happens on the highly integrated laptop chipsets named after geographical places: baytrail, broxton, cannonlake, cedarfork, cherryview, denverton, geminilake, lewisburg, merrifield, sunrisepoint... It started a while back and now it is ever more evident that this is crucial infrastructure for x86 laptops and not an embedded obscurity anymore. Users need to be aware. (b) Pin control expanders on I2C and SPI that are arch-agnostic. Currently Semtech SX150X and Microchip MCP28x08 but more are expected. Users will have to be able to configure these in directly for their set-up. - Just go and select GPIOLIB now that we made sure that GPIOLIB is a very vanilla subsystem. Do not depend on it, if we need it, select it. - Exposing the pin control subsystem in menuconfig uncovered a bunch of obscure bugs that are now hopefully fixed, all more or less pertaining to Blackfin. - Unified namespace for cross-calls between pin control and GPIO. - New support for clock skew/delay generic DT bindings and generic pin config options for this. - Minor documentation improvements. Various: - The Renesas SH-PFC pin controller has evolved a lot. It seems Renesas are churning out new SoCs by the minute. - A bunch of non-critical fixes for the Rockchip driver. - Improve the use of library functions instead of open coding. - Support the MCP28018 variant in the MCP28x08 driver. - Static constifying" * tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits) pinctrl: gemini: Fix missing pad descriptions pinctrl: Add some depends on HAS_IOMEM pinctrl: samsung/s3c24xx: add CONFIG_OF dependency pinctrl: gemini: Fix GMAC groups pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support pinctrl: ti-iodelay: remove redundant unused variable dev pinctrl: max77620: Use common error handling code in max77620_pinconf_set() pinctrl: gemini: Implement clock skew/delay config pinctrl: gemini: Use generic DT parser pinctrl: Add skew-delay pin config and bindings pinctrl: armada-37xx: Add edge both type gpio irq support pinctrl: uniphier: remove eMMC hardware reset pin-mux pinctrl: rockchip: Add iomux-route switching support for rk3288 pinctrl: intel: Add Intel Cedar Fork PCH pin controller support pinctrl: intel: Make offset to interrupt status register configurable pinctrl: sunxi: Enforce the strict mode by default pinctrl: sunxi: Disable strict mode for old pinctrl drivers pinctrl: sunxi: Introduce the strict flag pinctrl: sh-pfc: Save/restore registers for PSCI system suspend pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description ...

Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

2017-11-15T01:23:44+00:00

Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v4.15 kernel cycle: Core: - Fix the semantics of raw GPIO to actually be raw. No inversion semantics as before, but also no open draining, and allow the raw operations to affect lines used for interrupts as the caller supposedly knows what they are doing if they are getting the big hammer. - Rewrote the __inner_function() notation calls to names that make more sense. I just find this kind of code disturbing. - Drop the .irq_base() field from the gpiochip since now all IRQs are mapped dynamically. This is nice. - Support for .get_multiple() in the core driver API. This allows us to read several GPIO lines with a single register read. This has high value for some usecases: it can be used to create oscilloscopes and signal analyzers and other things that rely on reading several lines at exactly the same instant. Also a generally nice optimization. This uses the new assign_bit() macro from the bitops lib that was ACKed by Andrew Morton and is implemented for two drivers, one of them being the generic MMIO driver so everyone using that will be able to benefit from this. - Do not allow requests of Open Drain and Open Source setting of a GPIO line simultaneously. If the hardware actually supports enabling both at the same time the electrical result would be disastrous. - A new interrupt chip core helper. This will be helpful to deal with "banked" GPIOs, which means GPIO controllers with several logical blocks of GPIO inside them. This is several gpiochips per device in the device model, in contrast to the case when there is a 1-to-1 relationship between a device and a gpiochip. New drivers: - Maxim MAX3191x industrial serializer, a very interesting piece of professional I/O hardware. - Uniphier GPIO driver. This is the GPIO block from the recent Socionext (ex Fujitsu and Panasonic) platform. - Tegra 186 driver. This is based on the new banked GPIO infrastructure. Other improvements: - Some documentation improvements. - Wakeup support for the DesignWare DWAPB GPIO controller. - Reset line support on the DesignWare DWAPB GPIO controller. - Several non-critical bug fixes and improvements for the Broadcom BRCMSTB driver. - Misc non-critical bug fixes like exotic errorpaths, removal of dead code etc. - Explicit comments on fall-through switch() statements" * tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits) gpio: tegra186: Remove tegra186_gpio_lock_class gpio: rcar: Add r8a77995 (R-Car D3) support pinctrl: bcm2835: Fix some merge fallout gpio: Fix undefined lock_dep_class gpio: Automatically add lockdep keys gpio: Introduce struct gpio_irq_chip.first gpio: Disambiguate struct gpio_irq_chip.nested gpio: Add Tegra186 support gpio: Export gpiochip_irq_{map,unmap}() gpio: Implement tighter IRQ chip integration gpio: Move lock_key into struct gpio_irq_chip gpio: Move irq_valid_mask into struct gpio_irq_chip gpio: Move irq_nested into struct gpio_irq_chip gpio: Move irq_chained_parent to struct gpio_irq_chip gpio: Move irq_default_type to struct gpio_irq_chip gpio: Move irq_handler to struct gpio_irq_chip gpio: Move irqdomain into struct gpio_irq_chip gpio: Move irqchip into struct gpio_irq_chip gpio: Introduce struct gpio_irq_chip pinctrl: armada-37xx: remove unused variable ...