kernel/linux.git/drivers/phy/samsung, branch v6.1.168

phy: exynos5-usbdrd: fix MPLL_MULTIPLIER and SSC_REFCLKSEL masks in refclk

2025-03-07T15:56:50+00:00

commit e2158c953c973adb49383ddea2504faf08d375b7 upstream. In exynos5_usbdrd_{pipe3,utmi}_set_refclk(), the masks PHYCLKRST_MPLL_MULTIPLIER_MASK and PHYCLKRST_SSC_REFCLKSEL_MASK are not inverted when applied to the register values. Fix it. Cc: stable@vger.kernel.org Fixes: 59025887fb08 ("phy: Add new Exynos5 USB 3.0 PHY driver") Signed-off-by: Kaustabh Chakraborty Reviewed-by: Krzysztof Kozlowski Reviewed-by: Anand Moon Link: https://lore.kernel.org/r/20250209-exynos5-usbdrd-masks-v1-1-4f7f83f323d7@disroot.org Signed-off-by: Vinod Koul Signed-off-by: Greg Kroah-Hartman

Merge tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

2022-08-05T02:30:35+00:00

Pull pci updates from Bjorn Helgaas: "Enumeration: - Consolidate duplicated 'next function' scanning and extend to allow 'isolated functions' on s390, similar to existing hypervisors (Niklas Schnelle) Resource management: - Implement pci_iobar_pfn() for sparc, which allows us to remove the sparc-specific pci_mmap_page_range() and pci_mmap_resource_range(). This removes the ability to map the entire PCI I/O space using /proc/bus/pci, but we believe that's already been broken since v2.6.28 (Arnd Bergmann) - Move common PCI definitions to asm-generic/pci.h and rework others to be be more specific and more encapsulated in arches that need them (Stafford Horne) Power management: - Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas) Virtualization: - Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate the functions but don't advertise an ACS capability (Pavan Chebbi) Error handling: - Clear PCI Status register during enumeration in case firmware left errors logged (Kai-Heng Feng) - When we have native control of AER, enable error reporting for all devices that support AER. Previously only a few drivers enabled this (Stefan Roese) - Keep AER error reporting enabled for switches. Previously we enabled this during enumeration but immediately disabled it (Stefan Roese) - Iterate over error counters instead of error strings to avoid printing junk in AER sysfs counters (Mohamed Khalfella) ASPM: - Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g., via sysfs, are not lost across power state changes (Kai-Heng Feng) Endpoint framework: - Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie) Endpoint embedded DMA controller driver: - Simplify and clean up support for the DesignWare embedded DMA (eDMA) controller (Frank Li, Serge Semin) Broadcom STB PCIe controller driver: - Avoid config space accesses when link is down because we can't recover from the CPU aborts these cause (Jim Quinlan) - Look for power regulators described under Root Ports in DT and enable them before scanning the secondary bus (Jim Quinlan) - Disable/enable regulators in suspend/resume (Jim Quinlan) Freescale i.MX6 PCIe controller driver: - Simplify and clean up clock and PHY management (Richard Zhu) - Disable/enable regulators in suspend/resume (Richard Zhu) - Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu) - Allow speeds faster than Gen2 (Richard Zhu) - Make link being down a non-fatal error so controller probe doesn't fail if there are no Endpoints connected (Richard Zhu) Loongson PCIe controller driver: - Add ACPI and MCFG support for Loongson LS7A (Huacai Chen) - Avoid config reads to non-existent LS2K/LS7A devices because a hardware defect causes machine hangs (Huacai Chen) - Work around LS7A integrated devices that report incorrect Interrupt Pin values (Jianmin Lv) Marvell Aardvark PCIe controller driver: - Add support for AER and Slot capability on emulated bridge (Pali Rohár) MediaTek PCIe controller driver: - Add Airoha EN7532 to DT binding (John Crispin) - Allow building of driver for ARCH_AIROHA (Felix Fietkau) MediaTek PCIe Gen3 controller driver: - Print decoded LTSSM state when the link doesn't come up (Jianjun Wang) NVIDIA Tegra194 PCIe controller driver: - Convert DT binding to json-schema (Vidya Sagar) - Add DT bindings and driver support for Tegra234 Root Port and Endpoint mode (Vidya Sagar) - Fix some Root Port interrupt handling issues (Vidya Sagar) - Set default Max Payload Size to 256 bytes (Vidya Sagar) - Fix Data Link Feature capability programming (Vidya Sagar) - Extend Endpoint mode support to devices beyond Controller-5 (Vidya Sagar) Qualcomm PCIe controller driver: - Rework clock, reset, PHY power-on ordering to avoid hangs and improve consistency (Robert Marko, Christian Marangi) - Move pipe_clk handling to PHY drivers (Dmitry Baryshkov) - Add IPQ60xx support (Selvam Sathappan Periakaruppan) - Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru) - Add support for more than 32 MSI interrupts (Dmitry Baryshkov) Renesas R-Car PCIe controller driver: - Convert DT binding to json-schema (Herve Codina) - Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver (Herve Codina) Samsung Exynos PCIe controller driver: - Fix phy-exynos-pcie driver so it follows the 'phy_init() before phy_power_on()' PHY programming model (Marek Szyprowski) Synopsys DesignWare PCIe controller driver: - Simplify and clean up the DWC core extensively (Serge Semin) - Fix an issue with programming the ATU for regions that cross a 4GB boundary (Serge Semin) - Enable the CDM check if 'snps,enable-cdm-check' exists; previously we skipped it if 'num-lanes' was absent (Serge Semin) - Allocate a 32-bit DMA-able page to be MSI target instead of using a driver data structure that may not be addressable with 32-bit address (Will McVicker) - Add DWC core support for more than 32 MSI interrupts (Dmitry Baryshkov) Xilinx Versal CPM PCIe controller driver: - Add DT binding and driver support for Versal CPM5 Gen5 Root Port (Bharat Kumar Gogada)" * tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits) PCI: imx6: Support more than Gen2 speed link mode PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers PCI: imx6: Reformat suspend callback to keep symmetric with resume PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier PCI: imx6: Disable clocks in reverse order of enable PCI: imx6: Do not hide PHY driver callbacks and refine the error handling PCI: imx6: Reduce resume time by only starting link if it was up before suspend PCI: imx6: Mark the link down as non-fatal error PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset() PCI: imx6: Turn off regulator when system is in suspend mode PCI: imx6: Call host init function directly in resume PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks PCI: imx6: Propagate .host_init() errors to caller PCI: imx6: Collect clock enables in imx6_pcie_clk_enable() PCI: imx6: Factor out ref clock disable to match enable PCI: imx6: Move imx6_pcie_clk_disable() earlier PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier PCI: imx6: Move PHY management functions together PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS() ...

phy: samsung: phy-exynos-pcie: sanitize init/power_on callbacks

2022-08-01T20:25:12+00:00

The exynos-pcie driver called phy_power_on() before phy_init() for some historical reasons. However the generic PHY framework assumes that the proper sequence is to call phy_init() first, then phy_power_on(). The operations done by both functions should be considered as one action and as such they are called by the exynos-pcie driver (without doing anything between them). The initialization is just a sequence of register writes, which cannot be altered without breaking the hardware operation. To match the generic PHY framework requirement, simply move all register writes to the phy_init()/phy_exit() and drop power_on()/power_off() callbacks. This way the driver will also work with the old (incorrect) PHY initialization call sequence. Link: https://lore.kernel.org/r/20220628220409.26545-1-m.szyprowski@samsung.com Reported-by: Bjorn Helgaas Signed-off-by: Marek Szyprowski Signed-off-by: Bjorn Helgaas Reviewed-by: Chanho Park Acked-by: Krzysztof Kozlowski Acked-By: Vinod Koul

phy: samsung-ufs: ufs: change phy on/off control

2022-07-08T05:08:59+00:00

The sequence of controlling ufs phy block should be below: 1) Power On - Turn off pmu isolation - Clock enable 2) Power Off - Clock disable - Turn on pmu isolation Signed-off-by: Chanho Park Reviewed-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20220706020255.151177-3-chanho61.park@samsung.com Signed-off-by: Vinod Koul

phy: samsung-ufs: convert phy clk usage to clk_bulk API

2022-07-08T05:08:59+00:00

Instead of using separated clock manipulation, this converts the phy clock usage to be clk_bulk APIs. By using this, we can completely remove has_symbol_clk check and symbol clk variables. Furthermore, clk_get should be moved to probe because there is no need to get them in the phy_init callback. Signed-off-by: Chanho Park Reviewed-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20220706020255.151177-2-chanho61.park@samsung.com Signed-off-by: Vinod Koul

phy: samsung-ufs: add support for FSD ufs phy driver

2022-06-17T00:18:37+00:00

Adds support for Tesla Full Self-Driving (FSD) ufs phy driver. This SoC has different cdr lock status offset. Signed-off-by: Bharat Uppal Signed-off-by: Alim Akhtar Reviewed-by: Chanho Park Reviewed-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20220610104119.66401-4-alim.akhtar@samsung.com Signed-off-by: Vinod Koul

phy: samsung-ufs: move cdr offset to drvdata

2022-06-17T00:18:37+00:00

Move CDR lock offset to drv data so that it can be extended for other SoCs which are having CDR lock at different register offset. Signed-off-by: Bharat Uppal Signed-off-by: Alim Akhtar Reviewed-by: Chanho Park Reviewed-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20220610104119.66401-3-alim.akhtar@samsung.com Signed-off-by: Vinod Koul

phy: samsung: exynosautov9-ufs: correct TSRV register configurations

2022-06-08T16:26:14+00:00

For exynos auto v9's UFS MPHY, We should use 0x50 offset of TSRV register configurations. So, it must be s/PHY_TRSV_REG_CFG/PHY_TRSV_REG_CFG_AUTOV9/g Fixes: d64519249e1d ("phy: samsung-ufs: support exynosauto ufs phy driver") Signed-off-by: Chanho Park Acked-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20220603050536.61957-1-chanho61.park@samsung.com Signed-off-by: Vinod Koul

phy: samsung: ufs: support secondary ufs phy

2022-06-08T16:21:33+00:00

To support secondary ufs phy device, we need to get an offset for phy isolation from the syscon DT node. If the first index argument of the node is existing, we can read the offset value and set it as isol->offset. Reviewed-by: Krzysztof Kozlowski Signed-off-by: Chanho Park Reviewed-by: Alim Akhtar Link: https://lore.kernel.org/r/20220607072907.127000-6-chanho61.park@samsung.com Signed-off-by: Vinod Koul

phy: samsung: ufs: remove drvdata from struct samsung_ufs_phy

2022-06-08T16:21:33+00:00

To change an offset of pmu_isol, we need to store its data instead of having drvdata's pointer. The definition of the pmu_isol structure should be extracted from samsung_ufs_phy_drvdata and rename the name with samsung_ufs_phy_ prefix. Suggested-by: Krzysztof Kozlowski Reviewed-by: Krzysztof Kozlowski Signed-off-by: Chanho Park Reviewed-by: Alim Akhtar Link: https://lore.kernel.org/r/20220607072907.127000-5-chanho61.park@samsung.com Signed-off-by: Vinod Koul