kernel/linux.git/drivers/phy/qualcomm, branch linux-7.0.y

phy: qcom: qmp-usbc: Fix out-of-bounds array access in dp swing config

2026-06-01T15:54:48+00:00

[ Upstream commit ea17fc4d7dc2ba6459b1a318962960520201baf1 ] swing_tbl and pre_emphasis_tbl are 4x4 arrays (valid indices 0-3), but the boundary check uses "> 4" instead of ">= 4", allowing index 4 to cause an out-of-bounds access. Reported-by: Dan Carpenter Fixes: 81791c45c8e0 ("phy: qcom: qmp-usbc: Add QCS615 USB/DP PHY config and DP mode support") Signed-off-by: Xiangxu Yin Reviewed-by: Dmitry Baryshkov Reviewed-by: Konrad Dybcio Link: https://patch.msgid.link/20260227-master-v1-1-8d91b9407fdb@oss.qualcomm.com Signed-off-by: Vinod Koul Signed-off-by: Sasha Levin

phy: qcom: edp: Fix AUX_CFG8 programming for DP mode

2026-06-01T15:54:28+00:00

commit bf237a9fcbbf9d658522f7315ffc04bf2d49be42 upstream. AUX_CFG8 depends on whether the PHY is operating in eDP or DP mode, not the selected swing/pre-emphasis table. All supported platforms already have the proper tables, so remove the unnecessary check. Cc: stable@vger.kernel.org Fixes: 6078b8ce070c ("phy: qcom: edp: Add set_mode op for configuring eDP/DP submode") Reviewed-by: Konrad Dybcio Reviewed-by: Dmitry Baryshkov Signed-off-by: Yongxing Mou Link: https://patch.msgid.link/20260427-edp_phy-v5-4-3bb876824475@oss.qualcomm.com Signed-off-by: Vinod Koul Signed-off-by: Greg Kroah-Hartman

phy: qcom: edp: Add eDP/DP mode switch support

2026-06-01T15:54:28+00:00

commit 3011c365a329cf2db6d55e8d684550dc88350436 upstream. The eDP PHY supports both eDP/DP modes, each requiring a different swing/pre-emphasis table. However, the driver currently uses a fixed static table for eDP programming rather than selecting the appropriate table based on the current mode. Add separate tables for eDP and DP modes, and select the appropriate table dynamically based on the current mode. Glymur's DP mode table differs from the other platforms, add a dedicated table for it. This also fixes the table mismatch for X1E80100 (eDP) and SA8775P (DP). Cc: stable@vger.kernel.org Fixes: 3f12bf16213c ("phy: qcom: edp: Add support for eDP PHY on SA8775P") Reviewed-by: Konrad Dybcio Signed-off-by: Yongxing Mou Link: https://patch.msgid.link/20260427-edp_phy-v5-2-3bb876824475@oss.qualcomm.com Signed-off-by: Vinod Koul Signed-off-by: Greg Kroah-Hartman

phy: qcom: edp: Unify generic DP/eDP swing and pre-emphasis tables

2026-06-01T15:54:28+00:00

commit fd672888cccd6b855154efe0ac78e7ce3e8ab088 upstream. The current eDP and DP swing/pre-emphasis tables do not match the HPG requirements for the supported platforms, correct the table accordingly. The generic tables which can be shared as follows: DP mode： -sa8775p/sc7280/sc8280xp/x1e80100 -glymur -sc8180x eDP mode(low vdiff): -glymur/sa8775p/sc8280xp/x1e80100 -sc7280 -sc8180x The proper tables for SC8180X and SC7280 will be added in a later patch, since they need separate table. Cc: stable@vger.kernel.org Fixes: f199223cb490 ("phy: qcom: Introduce new eDP PHY driver") Reviewed-by: Konrad Dybcio Reviewed-by: Dmitry Baryshkov Signed-off-by: Yongxing Mou Link: https://patch.msgid.link/20260427-edp_phy-v5-1-3bb876824475@oss.qualcomm.com Signed-off-by: Vinod Koul Signed-off-by: Greg Kroah-Hartman

phy: qcom-qmp-ufs: Fix kaanapali PHY PLL lock failure after SM8650 G4 fix

2026-06-01T15:54:28+00:00

commit 80305760d7a55b884fb9023c490b75568d1ea0b1 upstream. Commit 81af9e40e2e4 ("phy: qcom: qmp-ufs: Fix SM8650 PCS table for Gear 4") moved QPHY_V6_PCS_UFS_PLL_CNTL register configuration from the shared sm8650_ufsphy_g5_pcs table to the SM8650-specific sm8650_ufsphy_pcs base table to fix Gear 4 operation on SM8650. However, this change inadvertently broke kaanapali and SM8750 SoCs which also rely on the shared sm8650_ufsphy_g5_pcs table for Gear 5 configuration but use their own sm8750_ufsphy_pcs base table. After the change, kaanapali PHYs are left without the required PLL_CNTL = 0x33 setting, causing the PHY PLL to remain at its hardware reset default value, preventing PLL lock and resulting in DME_LINKSTARTUP timeouts. Fix this by adding the missing QPHY_V6_PCS_UFS_PLL_CNTL = 0x33 entry to the sm8750_ufsphy_pcs table, mirroring what the original commit already did for sm8650_ufsphy_pcs. Cc: stable@vger.kernel.org # v6.19.12 Fixes: 81af9e40e2e4 ("phy: qcom: qmp-ufs: Fix SM8650 PCS table for Gear 4") Signed-off-by: Nitin Rawat Reviewed-by: Abel Vesa Reviewed-by: Konrad Dybcio Reviewed-by: Manivannan Sadhasivam Link: https://patch.msgid.link/20260415104851.2763238-1-nitin.rawat@oss.qualcomm.com Signed-off-by: Vinod Koul Signed-off-by: Greg Kroah-Hartman

phy: qcom: m31-eusb2: clear PLL_EN during init

2026-05-07T04:13:48+00:00

commit 520a98bdf7ae0130e22d8adced3d69a2e211b41f upstream. The driver currently sets bit 0 of USB_PHY_CFG1 (PLL_EN) during PHY initialization. According to the M31 EUSB2 PHY hardware documentation, this bit is intended only for test/debug scenarios and does not control mission mode operation. Keeping PLL_EN asserted causes the PHY to draw additional current during USB bus suspend. Clearing this bit results in lower suspend power consumption without affecting normal operation. Update the driver to leave PLL_EN cleared as recommended by the hardware documentation. Fixes: 9c8504861cc4 ("phy: qcom: Add M31 based eUSB2 PHY driver") Cc: stable@vger.kernel.org Signed-off-by: Elson Serrao Reviewed-by: Konrad Dybcio Link: https://patch.msgid.link/20260217201130.2804550-1-elson.serrao@oss.qualcomm.com Signed-off-by: Vinod Koul Signed-off-by: Greg Kroah-Hartman

phy: qcom: qmp-ufs: Fix SM8650 PCS table for Gear 4

2026-02-27T15:16:57+00:00

According to internal documentation, on SM8650, when the PHY is configured in Gear 4, the QPHY_V6_PCS_UFS_PLL_CNTL register needs to have the same value as for Gear 5. At the moment, there is no board that comes with a UFS 3.x device, so this issue doesn't show up, but with the new Eliza SoC, which uses the same init sequence as SM8650, on the MTP board, the link startup fails with the current Gear 4 PCS table. So fix that by moving the entry into the PCS generic table instead, while keeping the value from Gear 5 configuration. Cc: stable@vger.kernel.org # v6.10 Fixes: b9251e64a96f ("phy: qcom: qmp-ufs: update SM8650 tables for Gear 4 & 5") Suggested-by: Nitin Rawat Signed-off-by: Abel Vesa Reviewed-by: Konrad Dybcio Reviewed-by: Neil Armstrong Tested-by: Neil Armstrong # on SM8650-HDK Link: https://patch.msgid.link/20260219-phy-qcom-qmp-ufs-fix-sm8650-pcs-g4-table-v1-1-f136505b57f6@oss.qualcomm.com Signed-off-by: Vinod Koul

Merge tag 'phy-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy

2026-02-17T19:40:04+00:00

Pull phy updates from Vinod Koul: "Core: - Add suuport for "rx-polarity" and "tx-polarity" device tree properties and phy common properties to manage this New Support: - Qualcomm Glymur PCIe Gen4 2-lanes PCIe phy, DP and edp phy, USB UNI PHY and SMB2370 eUSB2 repeater. SC8280xp QMP UFS PHY, Kaanapali PCIe phy and QMP PHY, QCS615 QMP USB3+DP PHY and driver support for that. - SpacemiT PCIe/combo PHY and K1 USB2 PHY driver. - HDMI 2.1 FRL configuration support and driver enabling for rockchip samsung-hdptx driver - TI TCAN1046 phy - Renesas RZ/V2H(P) and RZ/V2N usb3 - Mediatek MT8188 hdmi-phy - Google Tensor SoC USB PHY driver - Apple Type-C PHY Updates: - Subsystem conversion for clock round_rate() to determine_rate() - TI USB3 DT schema conversion - Samsung ExynosAutov920 usb3, combo hsphy and ssphy support" * tag 'phy-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (143 commits) phy: ti: phy-j721e-wiz: convert from divider_round_rate() to divider_determine_rate() dt-bindings: phy: ti,control-phy-otghs: convert to DT schema dt-bindings: phy: ti,phy-usb3: convert to DT schema phy: tegra: xusb: Remove unused powered_on variable phy: renesas: rcar-gen3-usb2: add regulator dependency phy: GOOGLE_USB: add TYPEC dependency phy: enter drivers/phy/Makefile even without CONFIG_GENERIC_PHY phy: renesas: rcar-gen3-usb2: Use mux-state for phyrst management phy: renesas: rcar-gen3-usb2: Add regulator for OTG VBUS control phy: renesas: rcar-gen3-usb2: Use devm_pm_runtime_enable() phy: renesas: rcar-gen3-usb2: Factor out VBUS control logic dt-bindings: phy: renesas,usb2-phy: Document RZ/G3E SoC dt-bindings: phy: renesas,usb2-phy: Document mux-states property dt-bindings: phy: renesas,usb2-phy: Document USB VBUS regulator phy: rockchip: samsung-hdptx: Add HDMI 2.1 FRL support phy: rockchip: samsung-hdptx: Extend rk_hdptx_phy_verify_hdmi_config() helper phy: rockchip: samsung-hdptx: Switch to driver specific HDMI config phy: rockchip: samsung-hdptx: Drop hw_rate driver data phy: rockchip: samsung-hdptx: Compute clk rate from PLL config phy: rockchip: samsung-hdptx: Cleanup *_cmn_init_seq lists ...

phy: qcom: edp: Fix NULL pointer dereference for phy v6 (x1e80100)

2026-01-14T13:37:30+00:00

For Glymur SoC support, the com_clk_fwd_cfg callback was added, and a stub implementation was added for the v4 of the hardware. However it was omitted for the v6, causing a NULL pointer dereference oops on Hamoa/Purwa (X1E/X1P) SoC devices. Fix by adding the appropriate stub. Fixes: add66a6673bc ("phy: qcom: edp: Add Glymur platform support") Reviewed-by: Abel Vesa Signed-off-by: Val Packett Reviewed-by: Neil Armstrong Reviewed-by: Dmitry Baryshkov Reviewed-by: Konrad Dybcio Tested-by: Yijie Yang # Purwa-IoT-EVK Link: https://patch.msgid.link/20260111083317.604754-1-val@packett.cool Signed-off-by: Vinod Koul

phy: qcom: qmp-combo: Add polarity inversion support for SAR2130P

2026-01-14T09:31:54+00:00

On SAR2130P QXR Platform, the CC Lines are inverted and the lane programming is to be done reverse compared to other targets. As per the HW specifics, Bit-2 of TYPEC_CTRL register indicates port select polarity. This bit is to be set for SAR2130P. Signed-off-by: Krishna Kurapati Reviewed-by: Dmitry Baryshkov Reviewed-by: Konrad Dybcio Link: https://patch.msgid.link/20251017203438.744197-1-krishna.kurapati@oss.qualcomm.com Signed-off-by: Vinod Koul