kernel/linux.git/drivers/pci, branch v5.4.50

PCI: amlogic: meson: Don't use FAST_LINK_MODE to set up link

2020-06-24T15:50:31+00:00

[ Upstream commit 87dccf09323fc363bd0d072fcc12b96622ab8c69 ] The vim3l board does not work with a standard PCIe switch (ASM1184e), spitting all kind of errors - hinting at HW misconfiguration (no link, port enumeration issues, etc). According to the the Synopsys DWC PCIe Reference Manual, in the section dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as: "Sets all internal timers to fast mode for simulation purposes." it is sound to set this bit from a simulation perspective, but on actual silicon, which expects timers to have a nominal value, it is not. Make sure the FAST_LINK_MODE bit is cleared when configuring the RC to solve this problem. Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver") Signed-off-by: Marc Zyngier [lorenzo.pieralisi@arm.com: commit log] Signed-off-by: Lorenzo Pieralisi Reviewed-by: Neil Armstrong Acked-by: Rob Herring Signed-off-by: Sasha Levin

PCI: dwc: Fix inner MSI IRQ domain registration

2020-06-24T15:50:31+00:00

[ Upstream commit 0414b93e78d87ecc24ae1a7e61fe97deb29fa2f4 ] On a system that uses the internal DWC MSI widget, I get this warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected: debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present! This is due to the fact that the DWC MSI code tries to register two IRQ domains for the same firmware node, without telling the low level code how to distinguish them (by setting a bus token). This further confuses debugfs which tries to create corresponding files for each domain. Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is the closest thing we have as to "generic MSI". Link: https://lore.kernel.org/r/20200501113921.366597-1-maz@kernel.org Signed-off-by: Marc Zyngier Signed-off-by: Lorenzo Pieralisi Acked-by: Jingoo Han Signed-off-by: Sasha Levin

PCI/PTM: Inherit Switch Downstream Port PTM settings from Upstream Port

2020-06-24T15:50:31+00:00

[ Upstream commit 7b38fd9760f51cc83d80eed2cfbde8b5ead9e93a ] Except for Endpoints, we enable PTM at enumeration-time. Previously we did not account for the fact that Switch Downstream Ports are not permitted to have a PTM capability; their PTM behavior is controlled by the Upstream Port (PCIe r5.0, sec 7.9.16). Since Downstream Ports don't have a PTM capability, we did not mark them as "ptm_enabled", which meant that pci_enable_ptm() on an Endpoint failed because there was no PTM path to it. Mark Downstream Ports as "ptm_enabled" if their Upstream Port has PTM enabled. Fixes: eec097d43100 ("PCI: Add pci_enable_ptm() for drivers to enable PTM on endpoints") Reported-by: Aditya Paluri Signed-off-by: Bjorn Helgaas Signed-off-by: Sasha Levin

PCI/PM: Assume ports without DLL Link Active train links in 100 ms

2020-06-24T15:50:28+00:00

[ Upstream commit ec411e02b7a2e785a4ed9ed283207cd14f48699d ] Kai-Heng Feng reported that it takes a long time (> 1 s) to resume Thunderbolt-connected devices from both runtime suspend and system sleep (s2idle). This was because some Downstream Ports that support > 5 GT/s do not also support Data Link Layer Link Active reporting. Per PCIe r5.0 sec 6.6.1: With a Downstream Port that supports Link speeds greater than 5.0 GT/s, software must wait a minimum of 100 ms after Link training completes before sending a Configuration Request to the device immediately below that Port. Software can determine when Link training completes by polling the Data Link Layer Link Active bit or by setting up an associated interrupt (see Section 6.7.3.3). Sec 7.5.3.6 requires such Ports to support DLL Link Active reporting, but at least the Intel JHL6240 Thunderbolt 3 Bridge [8086:15c0] and the Intel JHL7540 Thunderbolt 3 Bridge [8086:15ea] do not. Previously we tried to wait for Link training to complete, but since there was no DLL Link Active reporting, all we could do was wait the worst-case 1000 ms, then another 100 ms. Instead of using the supported speeds to determine whether to wait for Link training, check whether the port supports DLL Link Active reporting. The Ports in question do not, so we'll wait only the 100 ms required for Ports that support Link speeds <= 5 GT/s. This of course assumes these Ports always train the Link within 100 ms even if they are operating at > 5 GT/s, which is not required by the spec. [bhelgaas: commit log, comment] Link: https://bugzilla.kernel.org/show_bug.cgi?id=206837 Link: https://lore.kernel.org/r/20200514133043.27429-1-mika.westerberg@linux.intel.com Reported-by: Kai-Heng Feng Tested-by: Kai-Heng Feng Signed-off-by: Mika Westerberg Signed-off-by: Bjorn Helgaas Signed-off-by: Sasha Levin

PCI: Fix pci_register_host_bridge() device_register() error handling

2020-06-24T15:50:27+00:00

[ Upstream commit 1b54ae8327a4d630111c8d88ba7906483ec6010b ] If device_register() has an error, we should bail out of pci_register_host_bridge() rather than continuing on. Fixes: 37d6a0a6f470 ("PCI: Add pci_register_host_bridge() interface") Link: https://lore.kernel.org/r/20200513223859.11295-1-robh@kernel.org Signed-off-by: Rob Herring Signed-off-by: Bjorn Helgaas Reviewed-by: Lorenzo Pieralisi Reviewed-by: Arnd Bergmann Signed-off-by: Sasha Levin

PCI/ASPM: Allow ASPM on links to PCIe-to-PCI/PCI-X Bridges

2020-06-24T15:50:24+00:00

[ Upstream commit 66ff14e59e8a30690755b08bc3042359703fb07a ] 7d715a6c1ae5 ("PCI: add PCI Express ASPM support") added the ability for Linux to enable ASPM, but for some undocumented reason, it didn't enable ASPM on links where the downstream component is a PCIe-to-PCI/PCI-X Bridge. Remove this exclusion so we can enable ASPM on these links. The Dell OptiPlex 7080 mentioned in the bugzilla has a TI XIO2001 PCIe-to-PCI Bridge. Enabling ASPM on the link leading to it allows the Intel SoC to enter deeper Package C-states, which is a significant power savings. [bhelgaas: commit log] Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207571 Link: https://lore.kernel.org/r/20200505173423.26968-1-kai.heng.feng@canonical.com Signed-off-by: Kai-Heng Feng Signed-off-by: Bjorn Helgaas Reviewed-by: Mika Westerberg Signed-off-by: Sasha Levin

PCI: rcar: Fix incorrect programming of OB windows

2020-06-24T15:50:24+00:00

[ Upstream commit 2b9f217433e31d125fb697ca7974d3de3ecc3e92 ] The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between a CPU address (which is determined by the window number 'x') and a programmed PCI address - Thus allowing the controller to translate CPU accesses into PCI accesses. However the existing code incorrectly writes the CPU address - lets fix this by writing the PCI address instead. For memory transactions, existing DT users describe a 1:1 identity mapping and thus this change should have no effect. However the same isn't true for I/O. Link: https://lore.kernel.org/r/20191004132941.6660-1-andrew.murray@arm.com Fixes: c25da4778803 ("PCI: rcar: Add Renesas R-Car PCIe driver") Tested-by: Marek Vasut Signed-off-by: Andrew Murray Signed-off-by: Lorenzo Pieralisi Reviewed-by: Marek Vasut Signed-off-by: Sasha Levin

PCI: v3-semi: Fix a memory leak in v3_pci_probe() error handling paths

2020-06-24T15:50:24+00:00

[ Upstream commit bca718988b9008d0d5f504e2d318178fc84958c1 ] If we fails somewhere in 'v3_pci_probe()', we need to free 'host'. Use the managed version of 'pci_alloc_host_bridge()' to do that easily. The use of managed resources is already widely used in this driver. Link: https://lore.kernel.org/r/20200418081637.1585-1-christophe.jaillet@wanadoo.fr Fixes: 68a15eb7bd0c ("PCI: v3-semi: Add V3 Semiconductor PCI host driver") Signed-off-by: Christophe JAILLET [lorenzo.pieralisi@arm.com: commit log] Signed-off-by: Lorenzo Pieralisi Acked-by: Linus Walleij Signed-off-by: Sasha Levin

PCI: vmd: Filter resource type bits from shadow register

2020-06-24T15:50:17+00:00

[ Upstream commit 3e5095eebe015d5a4d566aa5e03c8621add5f0a7 ] Versions of VMD with the Host Physical Address shadow register use this register to calculate the bus address offset needed to do guest passthrough of the domain. This register shadows the Host Physical Address registers including the resource type bits. After calculating the offset, the extra resource type bits lead to the VMD resources being over-provisioned at the front and under-provisioned at the back. Example: pci 10000:80:02.0: reg 0x10: [mem 0xf801fffc-0xf803fffb 64bit] Expected: pci 10000:80:02.0: reg 0x10: [mem 0xf8020000-0xf803ffff 64bit] If other devices are mapped in the over-provisioned front, it could lead to resource conflict issues with VMD or those devices. Link: https://lore.kernel.org/r/20200528030240.16024-3-jonathan.derrick@intel.com Fixes: a1a30170138c9 ("PCI: vmd: Fix shadow offsets to reflect spec changes") Signed-off-by: Jon Derrick Signed-off-by: Lorenzo Pieralisi Signed-off-by: Sasha Levin

PCI: pci-bridge-emul: Fix PCIe bit conflicts

2020-06-24T15:50:15+00:00

[ Upstream commit c88d19181771bd189147681ef38fc1533ebeff4c ] This patch fixes two bit conflicts in the pci-bridge-emul driver: 1. Bit 3 of Device Status (19 of Device Control) is marked as both Write-1-to-Clear and Read-Only. It should be Write-1-to-Clear. The Read-Only and Reserved bitmasks are shifted by 1 bit due to this error. 2. Bit 12 of Slot Control is marked as both Read-Write and Reserved. It should be Read-Write. Link: https://lore.kernel.org/r/20200511162117.6674-2-jonathan.derrick@intel.com Signed-off-by: Jon Derrick Signed-off-by: Lorenzo Pieralisi Acked-by: Rob Herring Signed-off-by: Sasha Levin