kernel/linux.git/drivers/pci/controller/Kconfig, branch v5.10.257

Merge tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

2020-10-22T19:41:00+00:00

Pull PCI updates from Bjorn Helgaas: "Enumeration: - Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong Liu) - Add schedule point in pci_read_config() to reduce max latency (Jiang Biao) - Add Kconfig options for MPS/MRRS strategy (Jim Quinlan) Resource management: - Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo Pieralisi) PCIe native device hotplug: - Reduce noisiness on hot removal (Lukas Wunner) Power management: - Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds" that was done on the basis of spec typo (Bjorn Helgaas) - Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold ambiguity (Krzysztof Wilczyński) - Remove unused pcibios_pm_ops (Vaibhav Gupta) IOMMU: - Enable Translation Blocking for external devices to harden against DMA attacks (Rajat Jain) Error handling: - Add an ACPI APEI notifier chain for vendor CPER records to enable device-specific error handling (Shiju Jose) ASPM: - Remove struct aspm_register_info to simplify code (Saheed O. Bolarinwa) Amlogic Meson PCIe controller driver: - Build as module by default (Kevin Hilman) Ampere Altra PCIe controller driver: - Add MCFG quirk to work around non-standard ECAM implementation (Tuan Phan) Broadcom iProc PCIe controller driver: - Set affinity mask on MSI interrupts (Mark Tomlinson) Broadcom STB PCIe controller driver: - Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan) - Add DT bindings for more Brcmstb chips (Jim Quinlan) - Add bcm7278 register info (Jim Quinlan) - Add bcm7278 PERST# support (Jim Quinlan) - Add suspend and resume pm_ops (Jim Quinlan) - Add control of rescal reset (Jim Quinlan) - Set additional internal memory DMA viewport sizes (Jim Quinlan) - Accommodate MSI for older chips (Jim Quinlan) - Set bus max burst size by chip type (Jim Quinlan) - Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan) Freescale i.MX6 PCIe controller driver: - Use dev_err_probe() to reduce redundant messages (Anson Huang) Freescale Layerscape PCIe controller driver: - Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang) - Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao) - Add endpoint support for ls1088a, ls2088a (Xiaowei Bao) - Add endpoint test support for lS1088a (Xiaowei Bao) - Add MSI-X support for ls1088a (Xiaowei Bao) HiSilicon HIP PCIe controller driver: - Handle HIP-specific errors via ACPI APEI (Yicong Yang) HiSilicon Kirin PCIe controller driver: - Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo) Intel VMD host bridge driver: - Factor out physical offset, bus offset, IRQ domain, IRQ allocation (Jon Derrick) - Use generic PCI PM correctly (Jon Derrick) Marvell Aardvark PCIe controller driver: - Fix compilation on s390 (Pali Rohár) - Implement driver 'remove' function and allow to build it as module (Pali Rohár) - Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár) - Convert mvebu a3700 internal SMCC firmware return codes to errno (Pali Rohár) - Fix initialization with old Marvell's Arm Trusted Firmware (Pali Rohár) Microsoft Hyper-V host bridge driver: - Fix hibernation in case interrupts are not re-created (Dexuan Cui) NVIDIA Tegra PCIe controller driver: - Stop checking return value of debugfs_create() functions (Greg Kroah-Hartman) - Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin) Qualcomm PCIe controller driver: - Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith) Renesas R-Car PCIe controller driver: - Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints (Lad Prabhakar) - Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar) - Add DT support for r8a7742 (Lad Prabhakar) Socionext UniPhier Pro5 controller driver: - Add DT descriptions of iATU register (host and endpoint) (Kunihiko Hayashi) Synopsys DesignWare PCIe controller driver: - Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems unavoidable) (Hou Zhiqiang) - Fix endpoint Header Type check so multi-function devices work (Hou Zhiqiang) - Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang) - Stop leaking MSI page in suspend/resume (Jisheng Zhang) - Add common iATU register support instead of keystone-specific code (Kunihiko Hayashi) - Major config space access and other cleanups in dwc core and drivers that use it (al, exynos, histb, imx6, intel-gw, keystone, kirin, meson, qcom, tegra) (Rob Herring) - Add multiple PFs support for endpoint (Xiaowei Bao) - Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao) Miscellaneous: - Use fallthrough pseudo-keyword (Gustavo A. R. Silva) - Fix "0 used as NULL pointer" warnings (Gustavo Pimentel) - Fix "cast truncates bits from constant value" warnings (Gustavo Pimentel) - Remove redundant zeroing for sg_init_table() (Julia Lawall) - Use scnprintf(), not snprintf(), in sysfs "show" functions (Krzysztof Wilczyński) - Remove unused assignments (Krzysztof Wilczyński) - Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński) - Simplify bool comparisons (Krzysztof Wilczyński) - Use for_each_child_of_node() and for_each_node_by_name() (Qinglang Miao) - Simplify return expressions (Qinglang Miao)" * tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits) PCI: vmd: Update VMD PM to correctly use generic PCI PM PCI: vmd: Create IRQ allocation helper PCI: vmd: Create IRQ Domain configuration helper PCI: vmd: Create bus offset configuration helper PCI: vmd: Create physical offset helper PCI: v3-semi: Remove unneeded break PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus() PCI/ASPM: Remove struct pcie_link_state.l1ss PCI/ASPM: Remove struct aspm_register_info.l1ss_cap PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1 PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused) PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr PCI/ASPM: Remove struct aspm_register_info.latency_encoding PCI/ASPM: Remove struct aspm_register_info.enabled PCI/ASPM: Remove struct aspm_register_info.support PCI/ASPM: Use 'parent' and 'child' for readability PCI/ASPM: Move LTR path check to where it's used PCI/ASPM: Move pci_clear_and_set_dword() earlier PCI: dwc: Fix MSI page leakage in suspend/resume ...

Merge branch 'remotes/lorenzo/pci/brcmstb'

2020-10-21T14:58:38+00:00

- Make PCIE_BRCMSTB depend on and default to ARCH_BRCMSTB (Jim Quinlan) - Add DT bindings for 7278, 7216, 7211, and new properties (Jim Quinlan) - Add bcm7278 register info (Jim Quinlan) - Add suspend and resume pm_ops (Jim Quinlan) - Add bcm7278 PERST# support (Jim Quinlan) - Add control of RESCAL reset (Jim Quinlan) - Set additional internal memory DMA viewport sizes (Jim Quinlan) - Accommodate MSI for older chips (Jim Quinlan) - Set bus max burst size by chip type (Jim Quinlan) - Add bcm7211, bcm7216, bcm7445, bcm7278 to match list (Jim Quinlan) * remotes/lorenzo/pci/brcmstb: PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list PCI: brcmstb: Set bus max burst size by chip type PCI: brcmstb: Accommodate MSI for older chips PCI: brcmstb: Set additional internal memory DMA viewport sizes PCI: brcmstb: Add control of rescal reset PCI: brcmstb: Add bcm7278 PERST# support PCI: brcmstb: Add suspend and resume pm_ops PCI: brcmstb: Add bcm7278 register info dt-bindings: PCI: Add bindings for more Brcmstb chips PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB

Merge branch 'remotes/lorenzo/pci/aardvark'

2020-10-21T14:58:37+00:00

- Fix s390 build error (Pali Rohár) - Check for errors from pci_bridge_emul_init() (Pali Rohár) - Export pci-bridge-emul functions for use by modules (Pali Rohár) - Make aardvark driver modular (Pali Rohár) - Move PCIe reset code to advk_pcie_train_link() (Pali Rohár) - Convert internal SMCC firmware return codes to errno (Pali Rohár) - Fix initialization with old Marvell's Arm Trusted Firmware (Pali Rohár) * remotes/lorenzo/pci/aardvark: PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware phy: marvell: comphy: Convert internal SMCC firmware return codes to errno PCI: aardvark: Move PCIe reset card code to advk_pcie_train_link() PCI: aardvark: Implement driver 'remove' function and allow to build it as module PCI: pci-bridge-emul: Export API functions PCI: aardvark: Check for errors from pci_bridge_emul_init() call PCI: aardvark: Fix compilation on s390

PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB

2020-09-17T11:30:38+00:00

Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to ARCH_BRCMSTB. Link: https://lore.kernel.org/r/20200911175232.19016-2-james.quinlan@broadcom.com Signed-off-by: Jim Quinlan Signed-off-by: Lorenzo Pieralisi Reviewed-by: Rob Herring Acked-by: Florian Fainelli

PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable

2020-09-16T14:52:37+00:00

The arch_.*_msi_irq[s] fallbacks are compiled in whether an architecture requires them or not. Architectures which are fully utilizing hierarchical irq domains should never call into that code. It's not only architectures which depend on that by implementing one or more of the weak functions, there is also a bunch of drivers which relies on the weak functions which invoke msi_controller::setup_irq[s] and msi_controller::teardown_irq. Make the architectures and drivers which rely on them select them in Kconfig and if not selected replace them by stub functions which emit a warning and fail the PCI/MSI interrupt allocation. Signed-off-by: Thomas Gleixner Link: https://lore.kernel.org/r/20200826112333.992429909@linutronix.de

PCI: hip: Add handling of HiSilicon HIP PCIe controller errors

2020-09-16T09:30:42+00:00

The HiSilicon HIP PCIe controller is capable of handling errors on root port and performing port reset separately at each root port. Add error handling driver for HIP PCIe controller to log and report recoverable errors. Perform root port reset and restore link status after the recovery. Following are some of the PCIe controller's recoverable errors 1. completion transmission timeout error. 2. CRS retry counter over the threshold error. 3. ECC 2 bit errors 4. AXI bresponse/rresponse errors etc. The driver placed in the drivers/pci/controller/ because the HIP PCIe controller does not use DWC IP. Link: https://lore.kernel.org/r/20200903123456.1823-3-shiju.jose@huawei.com Signed-off-by: Yicong Yang Signed-off-by: Shiju Jose Signed-off-by: Lorenzo Pieralisi Acked-by: Bjorn Helgaas

PCI: aardvark: Implement driver 'remove' function and allow to build it as module

2020-09-07T13:27:53+00:00

Providing driver's 'remove' function allows kernel to bind and unbind devices from aardvark driver. It also allows to build aardvark driver as a module. Compiling aardvark as a module simplifies development and debugging of this driver as it can be reloaded at runtime without the need to reboot to new kernel. Link: https://lore.kernel.org/r/20200907111038.5811-5-pali@kernel.org Signed-off-by: Pali Rohár Signed-off-by: Lorenzo Pieralisi Reviewed-by: Marek Behún

PCI: xilinx-cpm: Add Versal CPM Root Port driver

2020-08-05T22:09:15+00:00

Add support for Versal CPM as Root Port. The Versal ACAP devices include CCIX-PCIe Module (CPM). The integrated block for CPM along with the integrated bridge can function as PCIe Root Port. Bridge error and legacy interrupts in Versal CPM are handled using Versal CPM specific interrupt line. [bhelgaas: fold in kerneldoc fix from https://lore.kernel.org/linux-acpi/20200729201224.26799-7-krzk@kernel.org/] Link: https://lore.kernel.org/r/1592312214-9347-3-git-send-email-bharat.kumar.gogada@xilinx.com Signed-off-by: Bharat Kumar Gogada Signed-off-by: Lorenzo Pieralisi Signed-off-by: Bjorn Helgaas Reviewed-by: Rob Herring

treewide: replace '---help---' in Kconfig files with 'help'

2020-06-13T16:57:21+00:00

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada

Merge tag 'pci-v5.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

2020-06-06T18:01:58+00:00

Pull PCI updates from Bjorn Helgaas: "Enumeration: - Program MPS for RCiEP devices (Ashok Raj) - Fix pci_register_host_bridge() device_register() error handling (Rob Herring) - Fix pci_host_bridge struct device release/free handling (Rob Herring) Resource management: - Allow resizing BARs for devices on root bus (Ard Biesheuvel) Power management: - Reduce Thunderbolt resume time by working around devices that don't support DLL Link Active reporting (Mika Westerberg) - Work around a Pericom USB controller OHCI/EHCI PME# defect (Kai-Heng Feng) Virtualization: - Add ACS quirk for Intel Root Complex Integrated Endpoints (Ashok Raj) - Avoid FLR for AMD Starship USB 3.0 (Kevin Buettner) - Avoid FLR for AMD Matisse HD Audio & USB 3.0 (Marcos Scriven) Error handling: - Use only _OSC (not HEST FIRMWARE_FIRST) to determine AER ownership (Alexandru Gagniuc, Kuppuswamy Sathyanarayanan) - Reduce verbosity by logging only ACPI_NOTIFY_DISCONNECT_RECOVER events (Kuppuswamy Sathyanarayanan) - Don't enable AER by default in Kconfig (Bjorn Helgaas) Peer-to-peer DMA: - Add AMD Zen Raven and Renoir Root Ports to whitelist (Alex Deucher) ASPM: - Allow ASPM on links to PCIe-to-PCI/PCI-X Bridges (Kai-Heng Feng) Endpoint framework: - Fix DMA channel release in test (Kunihiko Hayashi) - Add page size as argument to pci_epc_mem_init() (Lad Prabhakar) - Add support to handle multiple base for mapping outbound memory (Lad Prabhakar) Generic host bridge driver: - Support building as module (Rob Herring) - Eliminate pci_host_common_probe wrappers (Rob Herring) Amlogic Meson PCIe controller driver: - Don't use FAST_LINK_MODE to set up link (Marc Zyngier) Broadcom STB PCIe controller driver: - Disable ASPM L0s if 'aspm-no-l0s' in DT (Jim Quinlan) - Fix clk_put() error (Jim Quinlan) - Fix window register offset (Jim Quinlan) - Assert fundamental reset on initialization (Nicolas Saenz Julienne) - Add notify xHCI reset property (Nicolas Saenz Julienne) - Add init routine for Raspberry Pi 4 VL805 USB controller (Nicolas Saenz Julienne) - Sync with Raspberry Pi 4 firmware for VL805 initialization (Nicolas Saenz Julienne) Cadence PCIe controller driver: - Remove "cdns,max-outbound-regions" DT property (replaced by "ranges") (Kishon Vijay Abraham I) - Read 32-bit (not 16-bit) Vendor ID/Device ID property from DT (Kishon Vijay Abraham I) Marvell Aardvark PCIe controller driver: - Improve link training (Marek Behún) - Add PHY support (Marek Behún) - Add "phys", "max-link-speed", "reset-gpios" to dt-binding (Marek Behún) - Train link immediately after enabling training to work around detection issues with some cards (Pali Rohár) - Issue PERST via GPIO to work around detection issues (Pali Rohár) - Don't blindly enable ASPM L0s (Pali Rohár) - Replace custom macros by standard linux/pci_regs.h macros (Pali Rohár) Microsoft Hyper-V host bridge driver: - Fix probe failure path to release resource (Wei Hu) - Retry PCI bus D0 entry on invalid device state for kdump (Wei Hu) Renesas R-Car PCIe controller driver: - Fix incorrect programming of OB windows (Andrew Murray) - Add suspend/resume (Kazufumi Ikeda) - Rename pcie-rcar.c to pcie-rcar-host.c (Lad Prabhakar) - Add endpoint controller driver (Lad Prabhakar) - Fix PCIEPAMR mask calculation (Lad Prabhakar) - Add r8a77961 to DT binding (Yoshihiro Shimoda) Socionext UniPhier Pro5 controller driver: - Add endpoint controller driver (Kunihiko Hayashi) Synopsys DesignWare PCIe controller driver: - Program outbound ATU upper limit register (Alan Mikhak) - Fix inner MSI IRQ domain registration (Marc Zyngier) Miscellaneous: - Check for platform_get_irq() failure consistently (negative return means failure) (Aman Sharma) - Fix several runtime PM get/put imbalances (Dinghao Liu) - Use flexible-array and struct_size() helpers for code cleanup (Gustavo A. R. Silva) - Update & fix issues in bridge emulation of PCIe registers (Jon Derrick) - Add macros for bridge window names (PCI_BRIDGE_IO_WINDOW, etc) (Krzysztof Wilczyński) - Work around Intel PCH MROMs that have invalid BARs (Xiaochun Lee)" * tag 'pci-v5.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (100 commits) PCI: uniphier: Add Socionext UniPhier Pro5 PCIe endpoint controller driver PCI: Add ACS quirk for Intel Root Complex Integrated Endpoints PCI/DPC: Print IRQ number used by port PCI/AER: Use "aer" variable for capability offset PCI/AER: Remove redundant dev->aer_cap checks PCI/AER: Remove redundant pci_is_pcie() checks PCI/AER: Remove HEST/FIRMWARE_FIRST parsing for AER ownership PCI: tegra: Fix runtime PM imbalance on error PCI: vmd: Filter resource type bits from shadow register PCI: tegra194: Fix runtime PM imbalance on error dt-bindings: PCI: Add UniPhier PCIe endpoint controller description PCI: hv: Use struct_size() helper PCI: Rename _DSM constants to align with spec PCI: Avoid FLR for AMD Starship USB 3.0 PCI: Avoid FLR for AMD Matisse HD Audio & USB 3.0 x86/PCI: Drop unused xen_register_pirq() gsi_override parameter PCI: dwc: Use private data pointer of "struct irq_domain" to get pcie_port PCI: amlogic: meson: Don't use FAST_LINK_MODE to set up link PCI: dwc: Fix inner MSI IRQ domain registration PCI: dwc: pci-dra7xx: Use devm_platform_ioremap_resource_byname() ...