kernel/linux.git/drivers/net/wireless/ath, branch v4.19.77

ath10k: Change the warning message string

2019-08-04T07:30:53+00:00

commit 265df32eae5845212ad9f55f5ae6b6dcb68b187b upstream. The "WARNING" string confuses syzbot, which thinks it found a crash [1]. Change the string to avoid such problem. [1] https://lkml.org/lkml/2019/5/9/243 Reported-by: syzbot+c1b25598aa60dcd47e78@syzkaller.appspotmail.com Suggested-by: Greg Kroah-Hartman Signed-off-by: Fabio Estevam Reviewed-by: Greg Kroah-Hartman Signed-off-by: Kalle Valo Signed-off-by: Greg Kroah-Hartman

ath10k: destroy sdio workqueue while remove sdio module

2019-07-26T07:14:14+00:00

[ Upstream commit 3ed39f8e747a7aafeec07bb244f2c3a1bdca5730 ] The workqueue need to flush and destory while remove sdio module, otherwise it will have thread which is not destory after remove sdio modules. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

wil6210: drop old event after wmi_call timeout

2019-07-26T07:14:13+00:00

[ Upstream commit 1a276003111c0404f6bfeffe924c5a21f482428b ] This change fixes a rare race condition of handling WMI events after wmi_call expires. wmi_recv_cmd immediately handles an event when reply_buf is defined and a wmi_call is waiting for the event. However, in case the wmi_call has already timed-out, there will be no waiting/running wmi_call and the event will be queued in WMI queue and will be handled later in wmi_event_handle. Meanwhile, a new similar wmi_call for the same command and event may be issued. In this case, when handling the queued event we got WARN_ON printed. Fixing this case as a valid timeout and drop the unexpected event. Signed-off-by: Ahmad Masri Signed-off-by: Maya Erez Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

ath10k: fix PCIE device wake up failed

2019-07-26T07:14:12+00:00

[ Upstream commit 011d4111c8c602ea829fa4917af1818eb0500a90 ] Observed PCIE device wake up failed after ~120 iterations of soft-reboot test. The error message is "ath10k_pci 0000:01:00.0: failed to wake up device : -110" The call trace as below: ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait -> ath10k_pci_is_awake Once trigger the device to wake up, we will continuously check the RTC state until it returns RTC_STATE_V_ON or timeout. But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON. Occasionally, we get 0x7 on the fist read, we thought as a failure case, but actually is the right value, also verified with the spec. So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed ~2000 iterations. Tested HW: QCA9984 Signed-off-by: Miaoqing Pan Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

ath10k: add missing error handling

2019-07-26T07:14:12+00:00

[ Upstream commit 4b553f3ca4cbde67399aa3a756c37eb92145b8a1 ] In function ath10k_sdio_mbox_rx_alloc() [sdio.c], ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases. This will make the driver think the allocation for skb is successful and try to access the skb. If we enable failslab, system will easily crash with NULL pointer dereferencing. Call trace of CONFIG_FAILSLAB: ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio] process_sdio_pending_irqs+0x4c/0x174 sdio_run_irqs+0x3c/0x64 sdio_irq_work+0x1c/0x28 Fixes: d96db25d2025 ("ath10k: add initial SDIO support") Signed-off-by: Claire Chang Reviewed-by: Brian Norris Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

ath: DFS JP domain W56 fixed pulse type 3 RADAR detection

2019-07-26T07:13:58+00:00

[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ] Increase pulse width range from 1-2usec to 0-4usec. During data traffic HW occasionally fails detecting radar pulses, so that SW cannot get enough radar reports to achieve the success rate. Tested ath10k hw and fw: * QCA9888(10.4-3.5.1-00052) * QCA4019(10.4-3.2.1.1-00017) * QCA9984(10.4-3.6-00104) * QCA988X(10.2.4-1.0-00041) Tested ath9k hw: AR9300 Tested-by: Tamizh chelvam Signed-off-by: Tamizh chelvam Signed-off-by: Anilkumar Kolli Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

wil6210: fix spurious interrupts in 3-msi

2019-07-26T07:13:58+00:00

[ Upstream commit e10b0eddd5235aa5aef4e40b970e34e735611a80 ] Interrupt is set in ICM (ICR & ~IMV) rising trigger. As the driver masks the IRQ after clearing it, there can be a race where an additional spurious interrupt is triggered when the driver unmask the IRQ. This can happen in case HW triggers an interrupt after the clear and before the mask. To prevent the second spurious interrupt the driver needs to mask the IRQ before reading and clearing it. Signed-off-by: Maya Erez Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

ath10k: add peer id check in ath10k_peer_find_by_id

2019-07-26T07:13:58+00:00

[ Upstream commit 49ed34b835e231aa941257394716bc689bc98d9f ] For some SDIO chip, the peer id is 65535 for MPDU with error status, then test_bit will trigger buffer overflow for peer's memory, if kasan enabled, it will report error. Reason is when station is in disconnecting status, firmware do not delete the peer info since it not disconnected completely, meanwhile some AP will still send data packet to station, then hardware will receive the packet and send to firmware, firmware's logic will report peer id of 65535 for MPDU with error status. Add check for overflow the size of peer's peer_ids will avoid the buffer overflow access. Call trace of kasan: dump_backtrace+0x0/0x2ec show_stack+0x20/0x2c __dump_stack+0x20/0x28 dump_stack+0xc8/0xec print_address_description+0x74/0x240 kasan_report+0x250/0x26c __asan_report_load8_noabort+0x20/0x2c ath10k_peer_find_by_id+0x180/0x1e4 [ath10k_core] ath10k_htt_t2h_msg_handler+0x100c/0x2fd4 [ath10k_core] ath10k_htt_htc_t2h_msg_handler+0x20/0x34 [ath10k_core] ath10k_sdio_irq_handler+0xcc8/0x1678 [ath10k_sdio] process_sdio_pending_irqs+0xec/0x370 sdio_run_irqs+0x68/0xe4 sdio_irq_work+0x1c/0x28 process_one_work+0x3d8/0x8b0 worker_thread+0x508/0x7cc kthread+0x24c/0x264 ret_from_fork+0x10/0x18 Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

ath6kl: add some bounds checking

2019-07-26T07:13:58+00:00

[ Upstream commit 5d6751eaff672ea77642e74e92e6c0ac7f9709ab ] The "ev->traffic_class" and "reply->ac" variables come from the network and they're used as an offset into the wmi->stream_exist_for_ac[] array. Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[] array only has WMM_NUM_AC (4) elements. We need to add a couple bounds checks to prevent array overflows. I also modified one existing check from "if (traffic_class > 3) {" to "if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent. Fixes: bdcd81707973 (" Add ath6kl cleaned up driver") Signed-off-by: Dan Carpenter Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin

ath9k: Check for errors when reading SREV register

2019-07-26T07:13:58+00:00

[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ] Right now, if an error is encountered during the SREV register read (i.e. an EIO in ath9k_regread()), that error code gets passed all the way to __ath9k_hw_init(), where it is visible during the "Chip rev not supported" message. ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver ath: phy2: Unable to initialize hardware; initialization status: -95 ath: phy2: Unable to initialize hardware; initialization status: -95 ath9k_htc: Failed to initialize the device Check for -EIO explicitly in ath9k_hw_read_revisions() and return a boolean based on the success of the operation. Check for that in __ath9k_hw_init() and abort with a more debugging-friendly message if reading the revisions wasn't successful. ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits ath: phy2: Failed to read SREV register ath: phy2: Could not read hardware revision ath: phy2: Unable to initialize hardware; initialization status: -95 ath: phy2: Unable to initialize hardware; initialization status: -95 ath9k_htc: Failed to initialize the device This helps when debugging by directly showing the first point of failure and it could prevent possible errors if a 0x0f.3 revision is ever supported. Signed-off-by: Tim Schumacher Signed-off-by: Kalle Valo Signed-off-by: Sasha Levin