kernel/linux.git/drivers/net/wireless/ath, branch v4.17.1

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial

2018-04-05T18:56:35+00:00

Pull trivial tree updates from Jiri Kosina. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: kfifo: fix inaccurate comment tools/thermal: tmon: fix for segfault net: Spelling s/stucture/structure/ edd: don't spam log if no EDD information is present Documentation: Fix early-microcode.txt references after file rename tracing: Block comments should align the * on each line treewide: Fix typos in printk GenWQE: Fix a typo in two comments treewide: Align function definition open/close braces

ath: Remove unnecessary ath_bcast_mac and use eth_broadcast_addr

2018-03-29T09:10:26+00:00

Remove the static array and use the generic routine to set the Ethernet broadcast address. Signed-off-by: Joe Perches Signed-off-by: Kalle Valo

ath10k: fix vdev stats for 10.4 firmware

2018-03-29T09:04:12+00:00

Currently vdev stats displayed in fw_stats are applicable only for TLV based firmware and fix it for 10.4 firmware as of now. The vdev stats in 10.4 firmware is split into two parts (vdev_stats, vdev_stats_extended). The actual stats are captured only in extended vdev stats. In order to enable vdev stats, appropriate feature bit will be set on extended resource config. As FTM related counters are available only on newer 10.4 based firmware, these counters will be displayed only on valid data. Signed-off-by: Rajkumar Manoharan Signed-off-by: Kalle Valo

ath10k: fix recent bandwidth conversion bug

2018-03-29T09:02:49+00:00

The commit "cfg80211: make RATE_INFO_BW_20 the default" changed the index of RATE_INFO_BW_20, but the updates to ath10k missed the special bandwidth calculation case in ath10k_update_per_peer_tx_stats(). This will fix below warning, WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254 cfg80211_calculate_bitrate+0x174/0x220 invalid rate bw=1, mcs=9, nss=2 (unwind_backtrace) from (cfg80211_calculate_bitrate+0x174/0x220) (cfg80211_calculate_bitrate) from (nl80211_put_sta_rate+0x44/0x1dc)from (nl80211_put_sta_rate) from (nl80211_send_station+0x388/0xaf0) (nl80211_get_station+0xa8/0xec) [ end trace da8257d6a850e91a ] Fixes: 842be75c77cb ("cfg80211: make RATE_INFO_BW_20 the default") Signed-off-by: Christian Lamparter Signed-off-by: Anilkumar Kolli Signed-off-by: Kalle Valo

ath10k: advertize beacon_int_min_gcd

2018-03-29T09:01:19+00:00

This patch fixes regression caused by 0c317a02ca98 ("cfg80211: support virtual interfaces with different beacon intervals"), with this change cfg80211 expects the driver to advertize 'beacon_int_min_gcd' to support different beacon intervals in multivap scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019. Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and 1000msec respectively. Frimware: firmware-5.bin_10.4-3.5.3-00053 Fixes: 0c317a02ca98 ("cfg80211: support virtual interfaces with different beacon intervals") Signed-off-by: Anilkumar Kolli Signed-off-by: Kalle Valo

ath10k: fix TDLS peer TX data failure issue on encryped AP

2018-03-29T09:00:19+00:00

For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock data when M4 was sent successfully. For other encryption which didn't need 4-way handshake firmware will unblock the data when peer authorized. Since TDLS is 3-way handshake host need send authorize cmd to firmware to unblock data. Signed-off-by: Yingying Tang Signed-off-by: Kalle Valo

ath10k: avoid to set WEP key for TDLS peer

2018-03-29T09:00:12+00:00

TDLS peer do not need WEP key. Setting WEP key will lead to TDLS setup failure. Add fix to avoid setting WEP key for TDLS peer. Signed-off-by: Yingying Tang Signed-off-by: Kalle Valo

ath10k: enable TDLS peer inactivity detection

2018-03-29T09:00:06+00:00

Enable TDLS peer inactivity detetion feature. QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting. Set related parameters in TDLS WMI command to enable this feature. Signed-off-by: Yingying Tang Signed-off-by: Kalle Valo

ath10k: enable TDLS peer buffer STA feature

2018-03-29T08:59:58+00:00

Enable TDLS peer buffer STA feature. QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA, it reports this capability through wmi service map in wmi service ready event. Set related parameter in TDLS WMI command to enable this feature. Signed-off-by: Yingying Tang Signed-off-by: Kalle Valo

wcn36xx: dequeue all pending indicator messages

2018-03-29T08:58:44+00:00

In case wcn36xx_smd_rsp_process() is called more than once before hal_ind_work was dispatched, the messages will end up in hal_ind_queue, but wcn36xx_ind_smd_work() will only look at the first message in that list. Fix this by dequeing the messages from the list in a loop, and only stop when it's empty. This issue was found during a review of the driver. In my tests, that race never actually occured. Signed-off-by: Daniel Mack Reviewed-by: Bjorn Andersson Signed-off-by: Kalle Valo