kernel/linux.git/drivers/net/usb, branch v5.18.2

net: usb: aqc111: Fix out-of-bounds accesses in RX fixup

2022-04-06T14:22:49+00:00

aqc111_rx_fixup() contains several out-of-bounds accesses that can be triggered by a malicious (or defective) USB device, in particular: - The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds, causing OOB reads and (on big-endian systems) OOB endianness flips. - A packet can overlap the metadata array, causing a later OOB endianness flip to corrupt data used by a cloned SKB that has already been handed off into the network stack. - A packet SKB can be constructed whose tail is far beyond its end, causing out-of-bounds heap data to be considered part of the SKB's data. Found doing variant analysis. Tested it with another driver (ax88179_178a), since I don't have a aqc111 device to test it, but the code looks very similar. Signed-off-by: Marcin Kozlowski Signed-off-by: David S. Miller

net: usb: ax88179_178a: add Allied Telesis AT-UMCs

2022-03-25T01:32:14+00:00

Adds the driver_info and IDs for the AX88179 based Allied Telesis AT-UMC family of devices. Signed-off-by: Greg Jesionowski Link: https://lore.kernel.org/r/20220323220024.GA36800@test-HP-EliteDesk-800-G1-SFF Signed-off-by: Jakub Kicinski

Merge tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

2022-03-24T20:13:26+00:00

Pull networking updates from Jakub Kicinski: "The sprinkling of SPI drivers is because we added a new one and Mark sent us a SPI driver interface conversion pull request. Core ---- - Introduce XDP multi-buffer support, allowing the use of XDP with jumbo frame MTUs and combination with Rx coalescing offloads (LRO). - Speed up netns dismantling (5x) and lower the memory cost a little. Remove unnecessary per-netns sockets. Scope some lists to a netns. Cut down RCU syncing. Use batch methods. Allow netdev registration to complete out of order. - Support distinguishing timestamp types (ingress vs egress) and maintaining them across packet scrubbing points (e.g. redirect). - Continue the work of annotating packet drop reasons throughout the stack. - Switch netdev error counters from an atomic to dynamically allocated per-CPU counters. - Rework a few preempt_disable(), local_irq_save() and busy waiting sections problematic on PREEMPT_RT. - Extend the ref_tracker to allow catching use-after-free bugs. BPF --- - Introduce "packing allocator" for BPF JIT images. JITed code is marked read only, and used to be allocated at page granularity. Custom allocator allows for more efficient memory use, lower iTLB pressure and prevents identity mapping huge pages from getting split. - Make use of BTF type annotations (e.g. __user, __percpu) to enforce the correct probe read access method, add appropriate helpers. - Convert the BPF preload to use light skeleton and drop the user-mode-driver dependency. - Allow XDP BPF_PROG_RUN test infra to send real packets, enabling its use as a packet generator. - Allow local storage memory to be allocated with GFP_KERNEL if called from a hook allowed to sleep. - Introduce fprobe (multi kprobe) to speed up mass attachment (arch bits to come later). - Add unstable conntrack lookup helpers for BPF by using the BPF kfunc infra. - Allow cgroup BPF progs to return custom errors to user space. - Add support for AF_UNIX iterator batching. - Allow iterator programs to use sleepable helpers. - Support JIT of add, and, or, xor and xchg atomic ops on arm64. - Add BTFGen support to bpftool which allows to use CO-RE in kernels without BTF info. - Large number of libbpf API improvements, cleanups and deprecations. Protocols --------- - Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev. - Adjust TSO packet sizes based on min_rtt, allowing very low latency links (data centers) to always send full-sized TSO super-frames. - Make IPv6 flow label changes (AKA hash rethink) more configurable, via sysctl and setsockopt. Distinguish between server and client behavior. - VxLAN support to "collect metadata" devices to terminate only configured VNIs. This is similar to VLAN filtering in the bridge. - Support inserting IPv6 IOAM information to a fraction of frames. - Add protocol attribute to IP addresses to allow identifying where given address comes from (kernel-generated, DHCP etc.) - Support setting socket and IPv6 options via cmsg on ping6 sockets. - Reject mis-use of ECN bits in IP headers as part of DSCP/TOS. Define dscp_t and stop taking ECN bits into account in fib-rules. - Add support for locked bridge ports (for 802.1X). - tun: support NAPI for packets received from batched XDP buffs, doubling the performance in some scenarios. - IPv6 extension header handling in Open vSwitch. - Support IPv6 control message load balancing in bonding, prevent neighbor solicitation and advertisement from using the wrong port. Support NS/NA monitor selection similar to existing ARP monitor. - SMC - improve performance with TCP_CORK and sendfile() - support auto-corking - support TCP_NODELAY - MCTP (Management Component Transport Protocol) - add user space tag control interface - I2C binding driver (as specified by DMTF DSP0237) - Multi-BSSID beacon handling in AP mode for WiFi. - Bluetooth: - handle MSFT Monitor Device Event - add MGMT Adv Monitor Device Found/Lost events - Multi-Path TCP: - add support for the SO_SNDTIMEO socket option - lots of selftest cleanups and improvements - Increase the max PDU size in CAN ISOTP to 64 kB. Driver API ---------- - Add HW counters for SW netdevs, a mechanism for devices which offload packet forwarding to report packet statistics back to software interfaces such as tunnels. - Select the default NIC queue count as a fraction of number of physical CPU cores, instead of hard-coding to 8. - Expose devlink instance locks to drivers. Allow device layer of drivers to use that lock directly instead of creating their own which always runs into ordering issues in devlink callbacks. - Add header/data split indication to guide user space enabling of TCP zero-copy Rx. - Allow configuring completion queue event size. - Refactor page_pool to enable fragmenting after allocation. - Add allocation and page reuse statistics to page_pool. - Improve Multiple Spanning Trees support in the bridge to allow reuse of topologies across VLANs, saving HW resources in switches. - DSA (Distributed Switch Architecture): - replay and offload of host VLAN entries - offload of static and local FDB entries on LAG interfaces - FDB isolation and unicast filtering New hardware / drivers ---------------------- - Ethernet: - LAN937x T1 PHYs - Davicom DM9051 SPI NIC driver - Realtek RTL8367S, RTL8367RB-VB switch and MDIO - Microchip ksz8563 switches - Netronome NFP3800 SmartNICs - Fungible SmartNICs - MediaTek MT8195 switches - WiFi: - mt76: MediaTek mt7916 - mt76: MediaTek mt7921u USB adapters - brcmfmac: Broadcom BCM43454/6 - Mobile: - iosm: Intel M.2 7360 WWAN card Drivers ------- - Convert many drivers to the new phylink API built for split PCS designs but also simplifying other cases. - Intel Ethernet NICs: - add TTY for GNSS module for E810T device - improve AF_XDP performance - GTP-C and GTP-U filter offload - QinQ VLAN support - Mellanox Ethernet NICs (mlx5): - support xdp->data_meta - multi-buffer XDP - offload tc push_eth and pop_eth actions - Netronome Ethernet NICs (nfp): - flow-independent tc action hardware offload (police / meter) - AF_XDP - Other Ethernet NICs: - at803x: fiber and SFP support - xgmac: mdio: preamble suppression and custom MDC frequencies - r8169: enable ASPM L1.2 if system vendor flags it as safe - macb/gem: ZynqMP SGMII - hns3: add TX push mode - dpaa2-eth: software TSO - lan743x: multi-queue, mdio, SGMII, PTP - axienet: NAPI and GRO support - Mellanox Ethernet switches (mlxsw): - source and dest IP address rewrites - RJ45 ports - Marvell Ethernet switches (prestera): - basic routing offload - multi-chain TC ACL offload - NXP embedded Ethernet switches (ocelot & felix): - PTP over UDP with the ocelot-8021q DSA tagging protocol - basic QoS classification on Felix DSA switch using dcbnl - port mirroring for ocelot switches - Microchip high-speed industrial Ethernet (sparx5): - offloading of bridge port flooding flags - PTP Hardware Clock - Other embedded switches: - lan966x: PTP Hardward Clock - qca8k: mdio read/write operations via crafted Ethernet packets - Qualcomm 802.11ax WiFi (ath11k): - add LDPC FEC type and 802.11ax High Efficiency data in radiotap - enable RX PPDU stats in monitor co-exist mode - Intel WiFi (iwlwifi): - UHB TAS enablement via BIOS - band disablement via BIOS - channel switch offload - 32 Rx AMPDU sessions in newer devices - MediaTek WiFi (mt76): - background radar detection - thermal management improvements on mt7915 - SAR support for more mt76 platforms - MBSSID and 6 GHz band on mt7915 - RealTek WiFi: - rtw89: AP mode - rtw89: 160 MHz channels and 6 GHz band - rtw89: hardware scan - Bluetooth: - mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS) - Microchip CAN (mcp251xfd): - multiple RX-FIFOs and runtime configurable RX/TX rings - internal PLL, runtime PM handling simplification - improve chip detection and error handling after wakeup" * tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits) llc: fix netdevice reference leaks in llc_ui_bind() drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool ice: don't allow to run ice_send_event_to_aux() in atomic ctx ice: fix 'scheduling while atomic' on aux critical err interrupt net/sched: fix incorrect vlan_push_eth dest field net: bridge: mst: Restrict info size queries to bridge ports net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init() drivers: net: xgene: Fix regression in CRC stripping net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT net: dsa: fix missing host-filtered multicast addresses net/mlx5e: Fix build warning, detected write beyond size of field iwlwifi: mvm: Don't fail if PPAG isn't supported selftests/bpf: Fix kprobe_multi test. Revert "rethook: x86: Add rethook x86 implementation" Revert "arm64: rethook: Add arm64 rethook implementation" Revert "powerpc: Add rethook support" Revert "ARM: rethook: Add rethook arm implementation" netdevice: add missing dm_private kdoc net: bridge: mst: prevent NULL deref in br_mst_info_size() selftests: forwarding: Use same VRF for port and VLAN upper ...

Merge tag 'v5.17-rc8' into irq/core, to fix conflicts

2022-03-14T17:53:00+00:00

Conflicts: drivers/pinctrl/pinctrl-starfive.c Signed-off-by: Ingo Molnar

net: usb: asix: suspend embedded PHY if external is used

2022-03-12T11:50:56+00:00

In case external PHY is used, we need to take care of embedded PHY. Since there are no methods to disable this PHY from the MAC side and keeping RMII reference clock, we need to suspend it. This patch will reduce electrical noise (PHY is continuing to send FLPs) and power consumption by 0,22W. Signed-off-by: Oleksij Rempel Signed-off-by: David S. Miller

net: usb: asix: make use of mdiobus_get_phy and phy_connect_direct

2022-03-12T11:50:56+00:00

In most cases we use own mdio bus, there is no need to create and store string for the PHY address. Signed-off-by: Oleksij Rempel Signed-off-by: David S. Miller

net: usb: asix: store chipid to avoid reading it on reset

2022-03-12T11:50:56+00:00

We already read chipid on probe. There is no need to read it on reset. Signed-off-by: Oleksij Rempel Signed-off-by: David S. Miller

net: usb: asix: unify ax88772_resume code

2022-03-12T11:50:56+00:00

The only difference is the reset code, so remove not needed duplicates. Signed-off-by: Oleksij Rempel Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2022-03-11T01:16:56+00:00

net/dsa/dsa2.c commit afb3cc1a397d ("net: dsa: unlock the rtnl_mutex when dsa_master_setup() fails") commit e83d56537859 ("net: dsa: replay master state events in dsa_tree_{setup,teardown}_master") https://lore.kernel.org/all/20220307101436.7ae87da0@canb.auug.org.au/ drivers/net/ethernet/intel/ice/ice.h commit 97b0129146b1 ("ice: Fix error with handling of bonding MTU") commit 43113ff73453 ("ice: add TTY for GNSS module for E810T device") https://lore.kernel.org/all/20220310112843.3233bcf1@canb.auug.org.au/ drivers/staging/gdm724x/gdm_lte.c commit fc7f750dc9d1 ("staging: gdm724x: fix use after free in gdm_lte_rx()") commit 4bcc4249b4cf ("staging: Use netif_rx().") https://lore.kernel.org/all/20220308111043.1018a59d@canb.auug.org.au/ Signed-off-by: Jakub Kicinski

smsc95xx: Ignore -ENODEV errors when device is unplugged

2022-03-07T12:32:31+00:00

According to Documentation/driver-api/usb/URB.rst when a device is unplugged usb_submit_urb() returns -ENODEV. This error code propagates all the way up to usbnet_read_cmd() and usbnet_write_cmd() calls inside the smsc95xx.c driver during Ethernet cable unplug, unbind or reboot. This causes the following errors to be shown on reboot, for example: ci_hdrc ci_hdrc.1: remove, state 1 usb usb2: USB disconnect, device number 1 usb 2-1: USB disconnect, device number 2 usb 2-1.1: USB disconnect, device number 3 smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19 smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19 smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup usb 2-1.4: USB disconnect, device number 4 ci_hdrc ci_hdrc.1: USB bus 2 deregistered ci_hdrc ci_hdrc.0: remove, state 4 usb usb1: USB disconnect, device number 1 ci_hdrc ci_hdrc.0: USB bus 1 deregistered imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot! reboot: Restarting system Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and __smsc95xx_phy_wait_not_busy() and do not print error messages when -ENODEV is returned. Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx") Signed-off-by: Fabio Estevam Signed-off-by: David S. Miller