kernel/linux.git/drivers/net/usb/plusb.c, branch linux-4.20.y

usb: plusb: Add support for PL-27A1

2017-04-25T14:08:16+00:00

This patch adds support for the PL-27A1 by adding the appropriate USB ID's. This chip is used in the goobay Active USB 3.0 Data Link and Unitek Y-3501 cables. Signed-off-by: Roman Spychała Signed-off-by: David S. Miller

drivers/net/usb/plusb.c: Fix typo

2016-03-28T02:33:56+00:00

Signed-off-by: Diego Viola Signed-off-by: David S. Miller

usb: plusb: Add support for National Instruments host-to-host cable

2015-02-20T20:12:48+00:00

The National Instruments USB Host-to-Host Cable is based on the Prolific PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it. Signed-off-by: Ben Shelton Signed-off-by: David S. Miller

drivers/net: delete non-required instances of include

2014-01-16T19:53:26+00:00

None of these files are actually using any __init type directives and hence don't need to include . Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. This covers everything under drivers/net except for wireless, which has been submitted separately. Signed-off-by: Paul Gortmaker Signed-off-by: David S. Miller

usb: Fix FSF address in file headers

2013-12-06T17:37:55+00:00

Several files refer to an old address for the Free Software Foundation in the file header comment. Resolve by replacing the address with the URL so that we do not have to keep updating the header comments anytime the address changes. CC: Oliver Neukum CC: Steve Glendinning CC: Oliver Neukum Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller

usbnet: plusb: apply introduced usb command APIs

2012-10-26T07:36:51+00:00

Acked-by: Oliver Neukum Signed-off-by: Ming Lei Signed-off-by: David S. Miller

USB: Disable hub-initiated LPM for comms devices.

2012-05-18T22:42:55+00:00

Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp Cc: Marcel Holtmann Cc: Gustavo Padovan Cc: Johan Hedberg Cc: Hansjoerg Lipp Cc: Tilman Schmidt Cc: Karsten Keil Cc: Peter Korsgaard Cc: Jan Dumon Cc: Petko Manolov Cc: Steve Glendinning Cc: "John W. Linville" Cc: Kalle Valo Cc: "Luis R. Rodriguez" Cc: Jouni Malinen Cc: Vasanthakumar Thiagarajan Cc: Senthil Balasubramanian Cc: Christian Lamparter Cc: Brett Rudley Cc: Roland Vossen Cc: Arend van Spriel Cc: "Franky (Zhenhui) Lin" Cc: Kan Yan Cc: Dan Williams Cc: Jussi Kivilinna Cc: Ivo van Doorn Cc: Gertjan van Wingerde Cc: Helmut Schaa Cc: Herton Ronaldo Krzesinski Cc: Hin-Tak Leung Cc: Larry Finger Cc: Chaoming Li Cc: Daniel Drake Cc: Ulrich Kunitz Signed-off-by: Sarah Sharp

USB: convert drivers/net/* to use module_usb_driver()

2011-11-18T17:44:20+00:00

This converts the drivers in drivers/net/* to use the module_usb_driver() macro which makes the code smaller and a bit simpler. Added bonus is that it removes some unneeded kernel log messages about drivers loading and/or unloading. Cc: Wolfgang Grandegger Cc: Samuel Ortiz Cc: Oliver Neukum Cc: Peter Korsgaard Cc: Petko Manolov Cc: Steve Glendinning Cc: Christian Lamparter Cc: "John W. Linville" Cc: Dan Williams Cc: Jussi Kivilinna Cc: Ivo van Doorn Cc: Gertjan van Wingerde Cc: Helmut Schaa Cc: Herton Ronaldo Krzesinski Cc: Hin-Tak Leung Cc: Larry Finger Cc: Chaoming Li Cc: Lucas De Marchi Cc: "David S. Miller" Cc: Roel Kluin Cc: Paul Gortmaker Cc: Jiri Pirko Cc: Pavel Roskin Cc: Yoann DI-RUZZA Cc: George Signed-off-by: Greg Kroah-Hartman

usb: plusb: Add debug to reset function

2011-04-11T01:46:45+00:00

This patch adds some debug to the reset function to print out the reason why it fails. Signed-off-by: Simon Wood Signed-off-by: David S. Miller

usb: plusb: Add support for PL-25A1

2011-04-11T01:46:44+00:00

This patch adds support for the PL-25A1 by adding the appropriate USB ID's. This chip is used in the Belkin 'Windows Easy Transfer' Cables. Signed-off-by: Simon Wood Signed-off-by: David S. Miller