kernel/linux.git/drivers/net/phy, branch v6.18.35

net: phy: micrel: fix LAN8814 QSGMII soft reset

2026-06-09T10:28:52+00:00

[ Upstream commit e027c218c482c6a0ae1948129ccda3b0a2033368 ] LAN8814 QSGMII soft reset was moved into the probe function to avoid triggering it for each of 4 PHY-s in the package. However, that broke QSGMII link between the MAC and PHY on most LAN8814 PHY-s, specificaly for us on the Microchip LAN969x switch. Reading the QSGMII status registers it was visible that lanes were only partially synced. It looks like the reset timing is crucial, so lets move the reset back into the .config_init function but guard it with phy_package_init_once() to avoid it being triggered on each of 4 PHY-s in the package. Change the probe function to use phy_package_probe_once() for coma and PtP setup. Fixes: 96a9178a29a6 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface") Signed-off-by: Robert Marko Link: https://patch.msgid.link/20260428134138.1741253-1-robert.marko@sartura.hr Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

phy: mscc: Use PHY_ID_MATCH_EXACT for VSC8584, VSC8582, VSC8575, VSC856X

2026-06-09T10:28:32+00:00

[ Upstream commit 1bc80d673087e5704adbb3ee8e4b785c14899cce ] As the PHYs VSC8584, VSC8582, VSC8575 and VSC856X exists only as rev B, we can use PHY_ID_MATCH_EXACT to match exactly on revision B of the PHY. Because of this change then there is not need the check if it is a different revision than rev B in the function vsc8584_probe() as we already know that this will never happen. These changes are a preparation for the next patch because in that patch we will make the PHYs VSC8574 and VSC8572 to use vsc8584_probe() and these PHYs have multiple revision. Reviewed-by: Maxime Chevallier Signed-off-by: Horatiu Vultur Link: https://patch.msgid.link/20251023191350.190940-2-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: honor eee_disabled_modes in phy_advertise_eee_all()

2026-06-01T15:51:05+00:00

[ Upstream commit 8baa7506d793f0636e3f6f01b01ef7be19674d06 ] phy_advertise_eee_all() copies supported_eee into advertising_eee unconditionally, overwriting any filtering applied during phy_probe() based on DT eee-broken-* properties or driver-populated eee_disabled_modes. genphy_c45_ethtool_set_eee() calls this helper when user space passes an empty advertisement, undoing the filtering. Apply the same eee_disabled_modes mask in phy_advertise_eee_all() so the filtering survives the copy, matching the pattern in phy_probe() and phy_support_eee(). Fixes: b64691274f5d ("net: phy: add helper phy_advertise_eee_all") Signed-off-by: Nicolai Buchwitz Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-2-05b52626fa68@tipi-net.de Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: honor eee_disabled_modes in phy_support_eee()

2026-06-01T15:51:04+00:00

[ Upstream commit 3655063e083889ed4b79b7dda9cec65478dce09a ] phy_support_eee() copies supported_eee into advertising_eee unconditionally, overwriting any filtering applied during phy_probe() based on DT eee-broken-* properties or driver-populated eee_disabled_modes. MAC drivers that call phy_support_eee() after probe (e.g. bcmgenet, fec, lan743x, lan78xx, r8169) then cause the PHY to advertise EEE for modes the user marked as broken. The symptom is that ethtool --show-eee on the local interface reports "not supported" (supported & ~eee_disabled_modes is empty) while the link partner sees EEE negotiated and active. phy_probe() already filters advertising_eee via eee_disabled_modes after calling of_set_phy_eee_broken(). Apply the same mask in phy_support_eee() so the filtering survives the copy. Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE") Signed-off-by: Nicolai Buchwitz Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-1-05b52626fa68@tipi-net.de Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: DP83TC811: add reading of abilities

2026-06-01T15:51:00+00:00

[ Upstream commit c78bdba7b9666020c0832150a4fc4c0aebc7c6ac ] At this time the driver is not listing any speeds it supports. This should be ETHTOOL_LINK_MODE_100baseT1_Full_BIT for DP83TC811. Add the missing call for phylib to read the abilities. Fixes: b753a9faaf9a ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy") Suggested-by: Andrew Lunn Signed-off-by: Sven Schuchmann Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20260512071949.6218-1-schuchmann@schleissheimer.de [pabeni@redhat.com: dropped revision history] Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: phy: skip EEE advertisement write when autoneg is disabled

2026-06-01T15:50:42+00:00

commit 960e77ce14a83ef7f226e8e4b4d75765633ba48b upstream. genphy_c45_an_config_eee_aneg() writes the EEE advertisement to the auto-negotiation device's MMD register space (MDIO_MMD_AN, register MDIO_AN_EEE_ADV). These registers are read by the link partner only during auto-negotiation, so writing them while autoneg is disabled cannot influence the link. On some PHYs (e.g. Broadcom BCM54213PE) the write nevertheless reaches the chip and disturbs the receive datapath. Concretely, running ethtool -s eth0 speed 100 duplex full autoneg off ethtool --set-eee eth0 eee off leaves eth0 with TX working and RX completely silent on a Raspberry Pi 4 / CM4 board (bcmgenet + BCM54213PE in rgmii-rxid). Switching back to autoneg recovers the link. Prior to commit f26a29a038ee ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled"), the disable path was effectively a no-op because the helper read the stale eee_cfg.eee_enabled, so the underlying PHY behavior never surfaced. Bisected on rpi-6.12.y between commits 83943264 (good) and effcbc88 (bad) to f26a29a038ee. Fixes: f26a29a038ee ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled") Cc: stable@vger.kernel.org Signed-off-by: Nerijus Bendžiūnas Reviewed-by: Nicolai Buchwitz Tested-by: Nicolai Buchwitz Link: https://patch.msgid.link/20260516150251.879680-1-nerijus.bendziunas@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: phy: dp83869: fix setting CLK_O_SEL field.

2026-05-23T11:07:10+00:00

[ Upstream commit 46f74a3f7d57d9cc0110b09cbc8163fa0a01afa2 ] Table 7-121 in datasheet says we have to set register 0xc6 to value 0x10 before CLK_O_SEL can be modified. No more infos about this field found in datasheet. With this fix, setting of CLK_O_SEL field in IO_MUX_CFG register worked through dts property "ti,clk-output-sel" on a DP83869HMRGZR. Signed-off-by: Heiko Schocher Reviewed-by: Simon Horman Fixes: 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy") Link: https://patch.msgid.link/20260425031339.3318-1-hs@nabladev.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: phy: qcom: at803x: Use the correct bit to disable extended next page

2026-05-23T11:06:33+00:00

[ Upstream commit e7a62edd34b1b4bc5f979988efc2f81c075733fd ] As noted in the blamed commit, the AR8035 and other PHYs from this family advertise the Extended Next Page support by default, which may be understood by some partners as this PHY being multi-gig capable. The fix is to disable XNP advertising, which is done by setting bit 12 of the Auto-Negotiation Advertisement Register (MII_ADVERTISE). The blamed commit incorrectly uses MDIO_AN_CTRL1_XNP, which is bit 13 as per 802.3 : 45.2.7.1 AN control register (Register 7.0) BIT 12 in MII_ADVERTISE is wrapped by ADVERTISE_RESV, used by some drivers such as the aquantia one. 802.3 Clause 28 defines bit 12 as Extended Next Page ability, at least in recent versions of the standard. Let's add a define for it and use it in the at803x driver. Fixes: 3c51fa5d2afe ("net: phy: ar803x: disable extended next page bit") Signed-off-by: Maxime Chevallier Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20260410171021.1277138-1-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: fix a return path in get_phy_c45_ids()

2026-05-23T11:06:33+00:00

[ Upstream commit 6f533abe7bbad2eef1e42c639b6bb9dad2b02362 ] The return value of phy_c45_probe_present() is stored in "ret", not "phy_reg", fix this. "phy_reg" always has a positive value if we reach this return path (since it would have returned earlier otherwise), which means that the original goal of the patch of not considering -ENODEV fatal wasn't achieved. Fixes: 17b447539408 ("net: phy: c45 scanning: Don't consider -ENODEV fatal") Signed-off-by: Charles Perry Reviewed-by: Andrew Lunn Reviewed-by: Russell King (Oracle) Link: https://patch.msgid.link/20260409133654.3203336-1-charles.perry@microchip.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

device property: Make modifications of fwnode "flags" thread safe

2026-05-07T04:11:32+00:00

commit f72e77c33e4b5657af35125e75bab249256030f3 upstream. In various places in the kernel, we modify the fwnode "flags" member by doing either: fwnode->flags |= SOME_FLAG; fwnode->flags &= ~SOME_FLAG; This type of modification is not thread-safe. If two threads are both mucking with the flags at the same time then one can clobber the other. While flags are often modified while under the "fwnode_link_lock", this is not universally true. Create some accessor functions for setting, clearing, and testing the FWNODE flags and move all users to these accessor functions. New accessor functions use set_bit() and clear_bit(), which are thread-safe. Cc: stable@vger.kernel.org Fixes: c2c724c868c4 ("driver core: Add fw_devlink_parse_fwtree()") Reviewed-by: Andy Shevchenko Acked-by: Mark Brown Reviewed-by: Wolfram Sang Signed-off-by: Douglas Anderson Reviewed-by: Rafael J. Wysocki (Intel) Reviewed-by: Saravana Kannan Link: https://patch.msgid.link/20260317090112.v2.1.I0a4d03104ecd5103df3d76f66c8d21b1d15a2e38@changeid [ Fix fwnode_clear_flag() argument alignment, restore dropped blank line in fwnode_dev_initialized(), and remove unnecessary parentheses around fwnode_test_flag() calls. - Danilo ] Signed-off-by: Danilo Krummrich Signed-off-by: Greg Kroah-Hartman