kernel/linux.git/drivers/net/phy, branch v4.14.286

net: mdio: unexport __init-annotated mdio_bus_init()

2022-06-14T14:53:58+00:00

[ Upstream commit 35b42dce619701f1300fb8498dae82c9bb1f0263 ] EXPORT_SYMBOL and __init is a bad combination because the .init.text section is freed up after the initialization. Hence, modules cannot use symbols annotated __init. The access to a freed symbol may end up with kernel panic. modpost used to detect it, but it has been broken for a decade. Recently, I fixed modpost so it started to warn it again, then this showed up in linux-next builds. There are two ways to fix it: - Remove __init - Remove EXPORT_SYMBOL I chose the latter for this case because the only in-tree call-site, drivers/net/phy/phy_device.c is never compiled as modular. (CONFIG_PHYLIB is boolean) Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Reported-by: Stephen Rothwell Signed-off-by: Masahiro Yamada Reviewed-by: Florian Fainelli Reviewed-by: Russell King (Oracle) Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: micrel: Allow probing without .driver_data

2022-06-14T14:53:46+00:00

[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ] Currently, if the .probe element is present in the phy_driver structure and the .driver_data is not, a NULL pointer dereference happens. Allow passing .probe without .driver_data by inserting NULL checks for priv->type. Signed-off-by: Fabio Estevam Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: broadcom: Fix brcm_fet_config_init()

2022-04-20T07:08:21+00:00

[ Upstream commit bf8bfc4336f7a34e48b3bbd19b1542bf085bdc3d ] A Broadcom AC201 PHY (same entry as 5241) would be flagged by the Broadcom UniMAC MDIO controller as not completing the turn around properly since the PHY expects 65 MDC clock cycles to complete a write cycle, and the MDIO controller was only sending 64 MDC clock cycles as determined by looking at a scope shot. This would make the subsequent read fail with the UniMAC MDIO controller command field having MDIO_READ_FAIL set and we would abort the brcm_fet_config_init() function and thus not probe the PHY at all. After issuing a software reset, wait for at least 1ms which is well above the 1us reset delay advertised by the datasheet and issue a dummy read to let the PHY turn around the line properly. This read specifically ignores -EIO which would be returned by MDIO controllers checking for the line being turned around. If we have a genuine reaad failure, the next read of the interrupt status register would pick it up anyway. Fixes: d7a2ed9248a3 ("broadcom: Add AC131 phy support") Signed-off-by: Florian Fainelli Link: https://lore.kernel.org/r/20220324232438.1156812-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: marvell: Fix MDI-x polarity setting in 88e1118-compatible PHYs

2022-02-16T11:44:49+00:00

commit aec12836e7196e4d360b2cbf20cf7aa5139ad2ec upstream. When setting up autonegotiation for 88E1118R and compatible PHYs, a software reset of PHY is issued before setting up polarity. This is incorrect as changes of MDI Crossover Mode bits are disruptive to the normal operation and must be followed by a software reset to take effect. Let's patch m88e1118_config_aneg() to fix the issue mentioned before by invoking software reset of the PHY just after setting up MDI-x polarity. Fixes: 605f196efbf8 ("phy: Add support for Marvell 88E1118 PHY") Signed-off-by: Pavel Parkhomenko Reviewed-by: Serge Semin Suggested-by: Andrew Lunn Cc: stable@vger.kernel.org Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: sfp: ignore disabled SFP node

2022-02-08T17:16:25+00:00

commit 2148927e6ed43a1667baf7c2ae3e0e05a44b51a0 upstream. Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") added code which finds SFP bus DT node even if the node is disabled with status = "disabled". Because of this, when phylink is created, it ends with non-null .sfp_bus member, even though the SFP module is not probed (because the node is disabled). We need to ignore disabled SFP bus node. Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Signed-off-by: Marek Behún Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer") Signed-off-by: David S. Miller [ backport to 4.14 ] Signed-off-by: Marek Behún Signed-off-by: Greg Kroah-Hartman

net: phy: marvell: configure RGMII delays for 88E1118

2022-01-27T08:00:57+00:00

[ Upstream commit f22725c95ececb703c3f741e8f946d23705630b7 ] Corentin Labbe reports that the SSI 1328 does not work when allowing the PHY to operate at gigabit speeds, but does work with the generic PHY driver. This appears to be because m88e1118_config_init() writes a fixed value to the MSCR register, claiming that this is to enable 1G speeds. However, this always sets bits 4 and 5, enabling RGMII transmit and receive delays. The suspicion is that the original board this was added for required the delays to make 1G speeds work. Add the necessary configuration for RGMII delays for the 88E1118 to bring this into line with the requirements for RGMII support, and thus make the SSI 1328 work. Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502. Reported-by: Corentin Labbe Tested-by: Corentin Labbe Signed-off-by: Russell King (Oracle) Reviewed-by: Andrew Lunn Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: mdio: Demote probed message to debug print

2022-01-27T08:00:56+00:00

[ Upstream commit 7590fc6f80ac2cbf23e6b42b668bbeded070850b ] On systems with large numbers of MDIO bus/muxes the message indicating that a given MDIO bus has been successfully probed is repeated for as many buses we have, which can eat up substantial boot time for no reason, demote to a debug print. Reported-by: Maxime Bizon Signed-off-by: Florian Fainelli Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phylink: avoid mvneta warning when setting pause parameters

2021-11-26T10:40:32+00:00

[ Upstream commit fd8d9731bcdfb22d28e45bce789bcb211c868c78 ] mvneta does not support asymetric pause modes, and it flags this by the lack of AsymPause in the supported field. When setting pause modes, we check that pause->rx_pause == pause->tx_pause, but only when pause autoneg is enabled. When pause autoneg is disabled, we still allow pause->rx_pause != pause->tx_pause, which is incorrect when the MAC does not support asymetric pause, and causes mvneta to issue a warning. Fix this by removing the test for pause->autoneg, so we always check that pause->rx_pause == pause->tx_pause for network devices that do not support AsymPause. Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King (Oracle) Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

phy: micrel: ksz8041nl: do not use power down mode

2021-11-26T10:40:31+00:00

[ Upstream commit 2641b62d2fab52648e34cdc6994b2eacde2d27c1 ] Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using the power down mode bit (0.11). If the PHY is taken out of power down mode in a certain temperature range, the PHY enters a weird state which leads to continuously reporting RX errors. In that state, the MAC is not able to receive or send any Ethernet frames and the activity LED is constantly blinking. Since Linux is using the suspend callback when the interface is taken down, ending up in that state can easily happen during a normal startup. Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal clock recovery when using power down mode. Even the latest revision (A4, Revision ID 0x1513) seems to suffer that problem, and according to the errata is not going to be fixed. Remove the suspend/resume callback to avoid using the power down mode completely. [*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs") Signed-off-by: Stefan Agner Acked-by: Marcel Ziswiler Signed-off-by: Francesco Dolcini Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

Revert "net: mdiobus: Fix memory leak in __mdiobus_register"

2021-11-02T17:25:11+00:00

commit 10eff1f5788b6ffac212c254e2f3666219576889 upstream. This reverts commit ab609f25d19858513919369ff3d9a63c02cd9e2e. This patch is correct in the sense that we _should_ call device_put() in case of device_register() failure, but the problem in this code is more vast. We need to set bus->state to UNMDIOBUS_REGISTERED before calling device_register() to correctly release the device in mdiobus_free(). This patch prevents us from doing it, since in case of device_register() failure put_device() will be called 2 times and it will cause UAF or something else. Also, Reported-by: tag in revered commit was wrong, since syzbot reported different leak in same function. Link: https://lore.kernel.org/netdev/20210928092657.GI2048@kadam/ Acked-by: Yanfei Xu Signed-off-by: Pavel Skripkin Link: https://lore.kernel.org/r/f12fb1faa4eccf0f355788225335eb4309ff2599.1633024062.git.paskripkin@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman