kernel/linux.git/drivers/net/phy/smsc.c, branch v6.6.131

net: phy: smsc: add proper reset flags for LAN8710A

2025-08-28T14:28:29+00:00

[ Upstream commit 57ec5a8735dc5dccd1ee68afdb1114956a3fce0d ] According to the LAN8710A datasheet (Rev. B, section 3.8.5.1), a hardware reset is required after power-on, and the reference clock (REF_CLK) must be established before asserting reset. Signed-off-by: Buday Csaba Cc: Csókás Bence Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250728152916.46249-2-csokas.bence@prolan.hu Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: smsc: Fix link failure in forced mode with Auto-MDIX

2025-07-17T16:35:10+00:00

[ Upstream commit 9dfe110cc0f6ef42af8e81ce52aef34a647d0b8a ] Force a fixed MDI-X mode when auto-negotiation is disabled to prevent link instability. When forcing the link speed and duplex on a LAN9500 PHY (e.g., with `ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto mode, the PHY fails to establish a stable link. This occurs because the PHY's Auto-MDIX algorithm is not designed to operate when auto-negotiation is disabled. In this state, the PHY continuously toggles the TX/RX signal pairs, which prevents the link partner from synchronizing. This patch resolves the issue by detecting when auto-negotiation is disabled. If the MDI-X control mode is set to 'auto', the driver now forces a specific, stable mode (ETH_TP_MDI) to prevent the pair toggling. This choice of a fixed MDI mode mirrors the behavior the hardware would exhibit if the AUTOMDIX_EN strap were configured for a fixed MDI connection. Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel Cc: Andre Edich Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: smsc: Force predictable MDI-X state on LAN87xx

2025-07-17T16:35:10+00:00

[ Upstream commit 0713e55533c88a20edb53eea6517dc56786a0078 ] Override the hardware strap configuration for MDI-X mode to ensure a predictable initial state for the driver. The initial mode of the LAN87xx PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no documented way to read its latched status. This unpredictability means the driver cannot know if the PHY has initialized with Auto-MDIX enabled or disabled, preventing it from providing a reliable interface to the user. This patch introduces a `config_init` hook that forces the PHY into a known state by explicitly enabling Auto-MDIX. Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel Cc: Andre Edich Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: smsc: Fix Auto-MDIX configuration when disabled by strap

2025-07-17T16:35:10+00:00

[ Upstream commit a141af8eb2272ab0f677a7f2653874840bc9b214 ] Correct the Auto-MDIX configuration to ensure userspace settings are respected when the feature is disabled by the AUTOMDIX_EN hardware strap. The LAN9500 PHY allows its default MDI-X mode to be configured via a hardware strap. If this strap sets the default to "MDI-X off", the driver was previously unable to enable Auto-MDIX from userspace. When handling the ETH_TP_MDI_AUTO case, the driver would set the SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY falls back to its hardware strap default, ignoring the software request. This patch corrects the behavior by also setting the override bit when enabling Auto-MDIX. This ensures that the userspace configuration takes precedence over the hardware strap, allowing Auto-MDIX to be enabled correctly in all scenarios. Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel Cc: Andre Edich Reviewed-by: Maxime Chevallier Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: smsc: add WoL support to LAN8740/LAN8742 PHYs

2023-07-27T04:24:40+00:00

Microchip LAN8740/LAN8742 PHYs support basic unicast, broadcast, and Magic Packet WoL. They have one pattern filter matching up to 128 bytes of frame data, which can be used to implement ARP or multicast WoL. ARP WoL matches any ARP frame with broadcast address. Multicast WoL matches any multicast frame. Signed-off-by: Tristram Ha Reviewed-by: Florian Fainelli Reviewed-by: Simon Horman Link: https://lore.kernel.org/r/1690329270-2873-1-git-send-email-Tristram.Ha@microchip.com Signed-off-by: Jakub Kicinski

net: phy: smsc: enable edpd tunable support

2023-04-03T09:08:43+00:00

Enable EDPD PHY tunable support for all drivers using lan87xx_read_status. Signed-off-by: Heiner Kallweit Reviewed-by: Simon Horman Signed-off-by: David S. Miller

net: phy: smsc: add support for edpd tunable

2023-04-03T09:08:43+00:00

This adds support for the EDPD PHY tunable. Per default EDPD is disabled in interrupt mode, the tunable can be used to override this, e.g. if the link partner doesn't use EDPD. The interval to check for energy can be chosen between 1000ms and 2000ms. Note that this value consists of the 1000ms phylib interval for state machine runs plus the time to wait for energy being detected. v2: - consider that phylib core holds phydev->lock when calling the phy tunable hooks Signed-off-by: Heiner Kallweit Reviewed-by: Simon Horman Signed-off-by: David S. Miller

net: phy: smsc: prepare for making edpd wait period configurable

2023-04-03T09:08:42+00:00

Add a member edpd_max_wait_ms to the private data structure in preparation of making the wait period configurable by supporting the edpd phy tunable. v2: - rename constant to EDPD_MAX_WAIT_DFLT_MS Signed-off-by: Heiner Kallweit Reviewed-by: Simon Horman Signed-off-by: David S. Miller

net: phy: smsc: add flag edpd_mode_set_by_user

2023-04-03T09:08:42+00:00

Add flag edpd_mode_set_by_user in preparation of adding edpd phy tunable support. This flag will allow users to override the default behavior of edpd being disabled if interrupt mode is used. Signed-off-by: Heiner Kallweit Reviewed-by: Simon Horman Signed-off-by: David S. Miller

net: phy: smsc: clear edpd_enable if interrupt mode is used

2023-04-03T09:08:42+00:00

Clear edpd_enable if interupt mode is used, this avoids having to check for PHY_POLL multiple times. Signed-off-by: Heiner Kallweit Reviewed-by: Simon Horman Signed-off-by: David S. Miller