kernel/linux.git/drivers/net/phy/sfp.c, branch v5.19

net: sfp: fix memory leak in sfp_probe()

2022-06-30T09:38:16+00:00

sfp_probe() allocates a memory chunk from sfp with sfp_alloc(). When devm_add_action() fails, sfp is not freed, which leads to a memory leak. We should use devm_add_action_or_reset() instead of devm_add_action(). Signed-off-by: Jianglei Nie Reviewed-by: Russell King (Oracle) Link: https://lore.kernel.org/r/20220629075550.2152003-1-niejianglei2021@163.com Signed-off-by: Paolo Abeni

net: sfp: Add tx-fault workaround for Huawei MA5671A SFP ONT

2022-05-03T23:53:39+00:00

As noted elsewhere, various GPON SFP modules exhibit non-standard TX-fault behaviour. In the tested case, the Huawei MA5671A, when used in combination with a Marvell mv88e6085 switch, was found to persistently assert TX-fault, resulting in the module being disabled. This patch adds a quirk to ignore the SFP_F_TX_FAULT state, allowing the module to function. Change from v1: removal of erroneous return statment (Andrew Lunn) Signed-off-by: Matthew Hagan Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/20220502223315.1973376-1-mnhagan88@gmail.com Signed-off-by: Jakub Kicinski

net: sfp: use %pe for printing errors

2022-03-03T06:03:34+00:00

Convert sfp to use %pe for printing error codes, which can print them as errno symbols rather than numbers. Signed-off-by: Russell King (Oracle) Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/E1nOyEN-00BuuE-OB@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski

net: sfp: fix high power modules without diagnostic monitoring

2022-01-17T16:30:44+00:00

Commit 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules") unintetionally changed the semantics for high power modules without the digital diagnostics monitoring. We repeatedly attempt to read the power status from the non-existing 0xa2 address in a futile hope this failure is temporary: [ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408 [ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode [ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5 [ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5 [ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5 We previosuly assumed such modules were powered up in the correct mode, continuing without further configuration as long as the required power class was supported by the host. Restore this behaviour, while preserving the intent of subsequent patches to avoid the "Address Change Sequence not supported" warning if we are not going to be accessing the DDM address. Fixes: 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules") Reported-by: 照山周一郎 Tested-by: 照山周一郎 Signed-off-by: Russell King (Oracle) Signed-off-by: David S. Miller

net: sfp: Fix typo in state machine debug string

2021-10-05T12:08:13+00:00

The string should be "tx_disable" to match the state enum. Fixes: 4005a7cb4f55 ("net: phy: sftp: print debug message with text, not numbers") Signed-off-by: Sean Anderson Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phy: delete repeated words of comments

2021-06-16T19:34:07+00:00

There are some repeated words in some comments, they should be deleted. Signed-off-by: Wenpeng Liang Signed-off-by: Weihang Li Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

phy: sfp: add netlink SFP support to generic SFP code

2021-04-11T23:34:56+00:00

The new netlink API for reading SFP data requires a new op to be implemented. The idea of the new netlink SFP code is that userspace is responsible to parsing the EEPROM data and requesting pages, rather than have the kernel decide what pages are interesting and returning them. This allows greater flexibility for newer formats. Currently the generic SFP code only supports simple SFPs. Allow i2c address 0x50 and 0x51 to be accessed with page and bank must always be 0. This interface will later be extended when for example QSFP support is added. Signed-off-by: Andrew Lunn Signed-off-by: Vladyslav Tarasiuk Signed-off-by: David S. Miller

net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant

2021-01-28T21:41:17+00:00

The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical information stored in its EEPROM. It claims to support all transceiver types including 10G Ethernet. Clear all claimed modes and set only 1000baseX_Full, which is the only one supported. This module has also phys_id set to SFF, and the SFP subsystem currently does not allow to use SFP modules detected as SFFs. Add exception for this module so it can be detected as supported. This change finally allows to detect and use SFP GPON module Ubiquiti U-Fiber Instant on Linux system. EEPROM content of this SFP module is (where XX is serial number): 00: 02 04 0b ff ff ff ff ff ff ff ff 03 0c 00 14 c8 ???........??.?? 10: 00 00 00 00 55 42 4e 54 20 20 20 20 20 20 20 20 ....UBNT 20: 20 20 20 20 00 18 e8 29 55 46 2d 49 4e 53 54 41 .??)UF-INSTA 30: 4e 54 20 20 20 20 20 20 34 20 20 20 05 1e 00 36 NT 4 ??.6 40: 00 06 00 00 55 42 4e 54 XX XX XX XX XX XX XX XX .?..UBNTXXXXXXXX 50: 20 20 20 20 31 34 30 31 32 33 20 20 60 80 02 41 140123 `??A Signed-off-by: Pali Rohár Signed-off-by: Jakub Kicinski

net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips

2021-01-28T21:41:17+00:00

The workaround for VSOL V2801F brand based GPON SFP modules added in commit 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround") works only for IDs added explicitly to the list. Since there are rebranded modules where OEM vendors put different strings into the vendor name field, we cannot base workaround on IDs only. Moreover the issue which the above mentioned commit tried to work around is generic not only to VSOL based modules, but rather to all GPON modules based on Realtek RTL8672 and RTL9601C chips. These include at least the following GPON modules: * V-SOL V2801F * C-Data FD511GX-RM0 * OPTON GP801R * BAUDCOM BD-1234-SFM * CPGOS03-0490 v2.0 * Ubiquiti U-Fiber Instant * EXOT EGS1 These Realtek chips have broken EEPROM emulator which for N-byte read operation returns just the first byte of EEPROM data, followed by N-1 zeros. Introduce a new function, sfp_id_needs_byte_io(), which detects SFP modules with broken EEPROM emulator based on N-1 zeros and switch to 1 byte EEPROM reading operation. Function sfp_i2c_read() now always uses single byte reading when it is required and when function sfp_hwmon_probe() detects single byte access, it disables registration of hwmon device, because in this case we cannot reliably and atomically read 2 bytes as is required by the standard for retrieving values from diagnostic area. (These Realtek chips are broken in a way that violates SFP standards for diagnostic interface. Kernel in this case simply cannot do anything less of skipping registration of the hwmon interface.) This patch fixes reading of EEPROM content from SFP modules based on Realtek RTL8672 and RTL9601C chips. Diagnostic interface of EEPROM stays broken and cannot be fixed. Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround") Co-developed-by: Russell King Signed-off-by: Russell King Signed-off-by: Pali Rohár Signed-off-by: Jakub Kicinski

net: sfp: add debugfs support

2021-01-13T04:01:56+00:00

Add debugfs support to SFP so that the internal state of the SFP state machines and hardware signal state can be viewed from userspace, rather than having to compile a debug kernel to view state transitions in the kernel log. The 'state' output looks like: Module state: empty Module probe attempts: 0 0 Device state: up Main state: down Fault recovery remaining retries: 5 PHY probe remaining retries: 12 moddef0: 0 rx_los: 1 tx_fault: 1 tx_disable: 1 Reviewed-by: Andrew Lunn Signed-off-by: Russell King Link: https://lore.kernel.org/r/E1kyYRe-0004kN-3F@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski