kernel/linux.git/drivers/net/phy/micrel.c, branch v6.6.133

net: phy: micrel: Add ksz9131_resume()

2025-08-28T14:28:21+00:00

[ Upstream commit f25a7eaa897f21396e99f90809af82ca553c9d14 ] The Renesas RZ/G3E SMARC EVK uses KSZ9131RNXC phy. On deep power state, PHY loses the power and on wakeup the rgmii delays are not reconfigured causing it to fail. Replace the callback kszphy_resume()->ksz9131_resume() for reconfiguring the rgmii_delay when it exits from PM suspend state. Signed-off-by: Biju Das Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250711054029.48536-1-biju.das.jz@bp.renesas.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: micrel: fix KSZ8081/KSZ8091 cable test

2025-08-28T14:28:10+00:00

commit 49db61c27c4bbd24364086dc0892bd3e14c1502e upstream. Commit 21b688dabecb ("net: phy: micrel: Cable Diag feature for lan8814 phy") introduced cable_test support for the LAN8814 that reuses parts of the KSZ886x logic and introduced the cable_diag_reg and pair_mask parameters to account for differences between those chips. However, it did not update the ksz8081_type struct, so those members are now 0, causing no pairs to be tested in ksz886x_cable_test_get_status and ksz886x_cable_test_wait_for_completion to poll the wrong register for the affected PHYs (Basic Control/Reset, which is 0 in normal operation) and exit immediately. Fix this by setting both struct members accordingly. Fixes: 21b688dabecb ("net: phy: micrel: Cable Diag feature for lan8814 phy") Cc: stable@vger.kernel.org Signed-off-by: Florian Larysch Link: https://patch.msgid.link/20250723222250.13960-1-fl@n621.de Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: phy: micrel: Fix the KSZ9131 MDI-X status issue

2024-08-11T10:47:21+00:00

[ Upstream commit 84383b5ef4cd21b4a67de92afdc05a03b5247db9 ] The MDIX status is not accurately reflecting the current state after the link partner has manually altered its MDIX configuration while operating in forced mode. Access information about Auto mdix completion and pair selection from the KSZ9131's Auto/MDI/MDI-X status register Fixes: b64e6a8794d9 ("net: phy: micrel: Add PHY Auto/MDI/MDI-X set driver for KSZ9131") Signed-off-by: Raju Lakkaraju Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20240725071125.13960-1-Raju.Lakkaraju@microchip.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: micrel: add Microchip KSZ 9477 to the device table

2024-07-05T07:33:47+00:00

[ Upstream commit 54a4e5c16382e871c01dd82b47e930fdce30406b ] PHY_ID_KSZ9477 was supported but not added to the device table passed to MODULE_DEVICE_TABLE. Fixes: fc3973a1fa09 ("phy: micrel: add Microchip KSZ 9477 Switch PHY support") Signed-off-by: Enguerrand de Ribaucourt Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: Micrel KSZ8061: fix errata solution not taking effect problem

2024-06-21T12:38:16+00:00

[ Upstream commit 0a8d3f2e3e8d8aea8af017e14227b91d5989b696 ] KSZ8061 needs to write to a MMD register at driver initialization to fix an errata. This worked in 5.0 kernel but not in newer kernels. The issue is the main phylib code no longer resets PHY at the very beginning. Calling phy resuming code later will reset the chip if it is already powered down at the beginning. This wipes out the MMD register write. Solution is to implement a phy resume function for KSZ8061 to take care of this problem. Fixes: 232ba3a51cc2 ("net: phy: Micrel KSZ8061: link failure after cable connect") Signed-off-by: Tristram Ha Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: micrel: fix KSZ9477 PHY issues after suspend/resume

2024-06-21T12:38:14+00:00

[ Upstream commit 6149db4997f582e958da675092f21c666e3b67b7 ] When the PHY is powered up after powered down most of the registers are reset, so the PHY setup code needs to be done again. In addition the interrupt register will need to be setup again so that link status indication works again. Fixes: 26dd2974c5b5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver") Signed-off-by: Tristram Ha Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

2024-06-12T09:12:56+00:00

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ] When the interrupt is enabled, the function lan8841_config_intr tries to clear any pending interrupts by reading the interrupt status, then checks the return value for errors and then continue to enable the interrupt. It has been seen that once the system gets out of sleep mode, the interrupt status has the value 0x400 meaning that the PHY detected that the link was in low power. That is correct value but the problem is that the check is wrong. We try to check for errors but we return an error also in this case which is not an error. Therefore fix this by returning only when there is an error. Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY") Signed-off-by: Horatiu Vultur Reviewed-by: Suman Ghosh Reviewed-by: Andrew Lunn Reviewed-by: Russell King (Oracle) Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

2024-06-12T09:12:53+00:00

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ] Following a similar reinstate for the KSZ8081 and KSZ9031. Older kernels would use the genphy_soft_reset if the PHY did not implement a .soft_reset. The KSZ8061 errata described here: https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect") is back again without this soft reset. Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") Tested-by: Karim Ben Houcine Signed-off-by: Mathieu Othacehe Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: micrel: Fix receiving the timestamp in the frame for lan8841

2024-06-12T09:11:54+00:00

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ] The blamed commit started to use the ptp workqueue to get the second part of the timestamp. And when the port was set down, then this workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING is not enabled, then the ptp_clock is not initialized so then it would crash when it would try to access the delayed work. So then basically by setting up and then down the port, it would crash. The fix consists in checking if the ptp_clock is initialized and only then cancel the delayed work. Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841") Signed-off-by: Horatiu Vultur Reviewed-by: Simon Horman Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: micrel: Fix potential null pointer dereference

2024-04-10T14:35:52+00:00

commit 96c155943a703f0655c0c4cab540f67055960e91 upstream. In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may return NULL as ptp_header due to abnormal packet type or corrupted packet. Fix this bug by adding ptp_header check. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Aleksandr Mishin Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman