kernel/linux.git/drivers/net/phy/broadcom.c, branch linux-5.11.y

net: phy: broadcom: Fix RGMII delays for BCM50160 and BCM50610M

2021-03-30T12:30:27+00:00

[ Upstream commit b1dd9bf688b0dcc5a34dca660de46c7570bd9243 ] The PHY driver entry for BCM50160 and BCM50610M calls bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in order to configuration appropriate clock delays on the PHY, fix that. Fixes: 733336262b28 ("net: phy: Allow BCM5481x PHYs to setup internal TX/RX clock delay") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: broadcom: Set proper 1000BaseX/SGMII interface mode for BCM54616S

2021-03-30T12:30:27+00:00

[ Upstream commit 3afd0218992a8d1398e9791d6c2edd4c948ae7ee ] The default configuration for the BCM54616S PHY may not match the desired mode when using 1000BaseX or SGMII interface modes, such as when it is on an SFP module. Add code to explicitly set the correct mode using programming sequences provided by Bel-Fuse: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-sfp-1gbt-05-series.pdf https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-sfp-1gbt-06-series.pdf Signed-off-by: Robert Hancock Acked-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: broadcom: Avoid forward for bcm54xx_config_clock_delay()

2021-03-30T12:30:27+00:00

[ Upstream commit 133bf7b4fbbe58cff5492e37e95e75c88161f1b8 ] Avoid a forward declaration by moving the callers of bcm54xx_config_clock_delay() below its body. Signed-off-by: Florian Fainelli Reviewed-by: Vladimir Oltean Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: introduce phydev->port

2021-03-30T12:30:27+00:00

[ Upstream commit 4217a64e18a1647a0dbc68cb3169a5a06f054ec8 ] At the moment, PORT_MII is reported in the ethtool ops. This is odd because it is an interface between the MAC and the PHY and no external port. Some network card drivers will overwrite the port to twisted pair or fiber, though. Even worse, the MDI/MDIX setting is only used by ethtool if the port is twisted pair. Set the port to PORT_TP by default because most PHY drivers are copper ones. If there is fibre support and it is enabled, the PHY driver will set it to PORT_FIBRE. This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE; except for the genphy fallback driver. Suggested-by: Andrew Lunn Signed-off-by: Michael Walle Reviewed-by: Florian Fainelli Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: broadcom: Add power down exit reset state delay

2021-03-30T12:30:19+00:00

[ Upstream commit 7a1468ba0e02eee24ae1353e8933793a27198e20 ] Per the datasheet, when we clear the power down bit, the PHY remains in an internal reset state for 40us and then resume normal operation. Account for that delay to avoid any issues in the future if genphy_resume() changes. Fixes: fe26821fa614 ("net: phy: broadcom: Wire suspend/resume for BCM54810") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: phy: broadcom: remove use of ack_interrupt()

2020-11-06T00:32:39+00:00

In preparation of removing the .ack_interrupt() callback, we must replace its occurrences (aka phy_clear_interrupt), from the 2 places where it is called from (phy_enable_interrupts and phy_disable_interrupts), with equivalent functionality. This means that clearing interrupts now becomes something that the PHY driver is responsible of doing, before enabling interrupts and after clearing them. Make this driver follow the new contract. Cc: Michael Walle Cc: Florian Fainelli Signed-off-by: Ioana Ciornei Signed-off-by: Jakub Kicinski

net: phy: broadcom: implement generic .handle_interrupt() callback

2020-11-06T00:32:27+00:00

In an attempt to actually support shared IRQs in phylib, we now move the responsibility of triggering the phylib state machine or just returning IRQ_NONE, based on the IRQ status register, to the PHY driver. Having 3 different IRQ handling callbacks (.handle_interrupt(), .did_interrupt() and .ack_interrupt() ) is confusing so let the PHY driver implement directly an IRQ handler like any other device driver. Make this driver follow the new convention. Cc: Florian Fainelli Signed-off-by: Ioana Ciornei Tested-by: Michael Walle Signed-off-by: Jakub Kicinski

net: phy: broadcom: fix checkpatch complains about tabs

2020-05-16T20:38:33+00:00

This patch makes checkpatch happy for tabs Signed-off-by: Kevin Lo Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: phy: broadcom: add support for BCM54811 PHY

2020-05-15T17:56:31+00:00

The BCM54811 PHY shares many similarities with the already supported BCM54810 PHY but additionally requires some semi-unique configuration. Signed-off-by: Kevin Lo Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: phy: broadcom: Add support for BCM53125 internal PHYs

2020-04-18T22:50:32+00:00

BCM53125 has internal Gigabit PHYs which support interrupts as well as statistics, make it possible to configure both of those features with a PHY driver entry. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller