kernel/linux.git/drivers/net/ipa/ipa_endpoint.c, branch v5.19

net: ipa: fix page free in ipa_endpoint_replenish_one()

2022-05-28T01:29:50+00:00

Currently the (possibly compound) pages used for receive buffers are freed using __free_pages(). But according to this comment above the definition of that function, that's wrong: If you want to use the page's reference count to decide when to free the allocation, you should allocate a compound page, and use put_page() instead of __free_pages(). Convert the call to __free_pages() in ipa_endpoint_replenish_one() to use put_page() instead. Fixes: 6a606b90153b8 ("net: ipa: allocate transaction in replenish loop") Signed-off-by: Alex Elder Signed-off-by: Jakub Kicinski

net: ipa: fix page free in ipa_endpoint_trans_release()

2022-05-28T01:29:50+00:00

Currently the (possibly compound) page used for receive buffers are freed using __free_pages(). But according to this comment above the definition of that function, that's wrong: If you want to use the page's reference count to decide when to free the allocation, you should allocate a compound page, and use put_page() instead of __free_pages(). Convert the call to __free_pages() in ipa_endpoint_trans_release() to use put_page() instead. Fixes: ed23f02680caa ("net: ipa: define per-endpoint receive buffer size") Signed-off-by: Alex Elder Signed-off-by: Jakub Kicinski

net: ipa: count the number of modem TX endpoints

2022-05-22T19:46:12+00:00

In ipa_endpoint_modem_exception_reset_all(), a high estimate was made of the number of endpoints that need their status register updated. We only used what was needed, so the high estimate didn't matter much. However the next few patches are going to limit the number of commands in a single transaction, and the overestimate would exceed that. So count the number of modem TX endpoints at initialization time, and use it in ipa_endpoint_modem_exception_reset_all(). Signed-off-by: Alex Elder Signed-off-by: David S. Miller

net: ipa: kill gsi_trans_commit_wait_timeout()

2022-05-22T19:46:12+00:00

Since the beginning gsi_trans_commit_wait_timeout() has existed to provide a way to allow waiting a limited time for a transaction to complete. But that function has never been used. In fact, there is no use for this function, because a transaction committed to hardware should *always* complete. The only reason it might not complete is if there were a hardware failure, or perhaps a system configuration error. Furthermore, if a timeout ever did occur, the IPA hardware would be in an indeterminate state, from which there is no recovery. It would require some sort of complete IPA reset, and would require the participation of the modem, and at this time there is no such sequence defined. So get rid of the definition of gsi_trans_commit_wait_timeout(), and update a few comments accordingly. Signed-off-by: Alex Elder Signed-off-by: David S. Miller

net: ipa: specify RX aggregation time limit in config data

2022-05-22T19:46:12+00:00

Don't assume that a 500 microsecond time limit should be used for all receive endpoints that support aggregation. Instead, specify the time limit to use in the configuration data. Set a 500 microsecond limit for all existing RX endpoints, as before. Checking for overflow for the time limit field is a bit complicated. Rather than duplicate a lot of code in ipa_endpoint_data_valid_one(), call WARN() if any value is found to be too large when encoding it. Signed-off-by: Alex Elder Signed-off-by: David S. Miller

net: ipa: support hard aggregation limits

2022-05-22T19:46:12+00:00

Add a new flag for AP receive endpoints that indicates whether a "hard limit" is used as a criterion for closing aggregation. Add comments explaining the difference between "hard" and "soft" aggregation limits. Pass a flag to ipa_aggr_size_kb() so it computes the proper aggregation size value whether using hard or soft limits. Move that function earlier in "ipa_endpoint.c" so it can be used without a forward-reference. Update ipa_endpoint_data_valid_one() so it validates endpoints whose data indicate a hard aggregation limit is used, and so it reports set aggregation flags for endpoints without aggregation enabled. Signed-off-by: Alex Elder Signed-off-by: David S. Miller

net: ipa: make endpoint HOLB drop configurable

2022-05-22T19:46:12+00:00

Add a new Boolean flag for RX endpoints defining whether HOLB drop is initially enabled or disabled for the endpoint. All existing AP endpoints should have HOLB drop disabled. Signed-off-by: Alex Elder Signed-off-by: David S. Miller

net: ipa: save a copy of endpoint default config

2022-05-20T10:12:24+00:00

All elements of the default endpoint configuration are used in the code when programming an endpoint for use. But none of the other configuration data is ever needed once things are initialized. So rather than saving a pointer to *all* of the configuration data, save a copy of only the endpoint configuration portion. This will eventually allow endpoint configuration to be modifiable at runtime. But even before that it means we won't keep a pointer to configuration data after when no longer needed. Signed-off-by: Alex Elder Signed-off-by: David S. Miller

net: ipa: rename a few endpoint config data types

2022-05-20T10:12:24+00:00

Rename the just-moved data structure types to drop the "_data" suffix, to make it more obvious they are no longer meant to be used just as read-only initialization data. Rename the fields and variables of these types to use "config" instead of "data" in the name. This is another small step meant to facilitate review. Signed-off-by: Alex Elder Signed-off-by: David S. Miller

net: ipa: ignore endianness if there is no header

2022-05-20T10:12:23+00:00

If we program an RX endpoint to have no header (header length is 0), header-related endpoint configuration values are meaningless and are ignored. The only case we support that defines a header is QMAP endpoints. In ipa_endpoint_init_hdr_ext() we set the endianness mask value unconditionally, but it should not be done if there is no header (meaning it is not configured for QMAP). Set the endianness conditionally, and rearrange the logic in that function slightly to avoid testing the qmap flag twice. Delete an incorrect comment in ipa_endpoint_init_aggr(). Signed-off-by: Alex Elder Signed-off-by: David S. Miller