kernel/linux.git/drivers/net/ethernet/microchip, branch v6.19.11

net: lan743x: fix duplex configuration in mac_link_up

2026-04-02T11:25:29+00:00

[ Upstream commit 71399707876b93240f236f48b8062f3423a5fe97 ] The driver does not explicitly configure the MAC duplex mode when bringing the link up. As a result, the MAC may retain a stale duplex setting from a previous link state, leading to duplex mismatches with the link partner and degraded network performance. Update lan743x_phylink_mac_link_up() to set or clear the MAC_CR_DPX_ bit according to the negotiated duplex mode. This ensures the MAC configuration is consistent with the phylink resolved state. Fixes: a5f199a8d8a03 ("net: lan743x: Migrate phylib to phylink") Signed-off-by: Thangaraj Samynathan Reviewed-by: Russell King (Oracle) Link: https://patch.msgid.link/20260323065345.144915-1-thangaraj.s@microchip.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: sparx5/lan969x: fix PTP clock max_adj value

2026-02-26T23:01:30+00:00

[ Upstream commit a49d2a2c37a6252c41cbdd505f9d1c58d5a3817a ] The max_adj field in ptp_clock_info tells userspace how much the PHC clock frequency can be adjusted. ptp4l reads this and will never request a correction larger than max_adj. On both sparx5 and lan969x the clock offset may never converge because the servo needs a frequency correction larger than the current max_adj of 200000 (200 ppm) allows. The servo rails at the max and the offset stays in the tens of microseconds. The hardware has no inherent max adjustment limit; frequency correction is done by writing a 64-bit clock period increment to CLK_PER_CFG, and the register has plenty of range. The 200000 value was just an overly conservative software limit. The max_adj is shared between sparx5 and lan969x, and the increased value is safe for both. Fix this by increasing max_adj to 10000000 (10000 ppm), giving the servo sufficient headroom. Fixes: 0933bd04047c ("net: sparx5: Add support for ptp clocks") Signed-off-by: Daniel Machon Reviewed-by: Maxime Chevallier Link: https://patch.msgid.link/20260212-sparx5-ptp-max-adj-v2-v1-1-06b200e50ce3@microchip.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: sparx5/lan969x: fix DWRR cost max to match hardware register width

2026-02-26T23:01:29+00:00

[ Upstream commit 6c28aa8dfdf24f554d4c5d4ff7d723a95360d94a ] DWRR (Deficit Weighted Round Robin) scheduling distributes bandwidth across traffic classes based on per-queue cost values, where lower cost means higher bandwidth share. The SPX5_DWRR_COST_MAX constant is 63 (6 bits) but the hardware register field HSCH_DWRR_ENTRY_DWRR_COST is GENMASK(24, 20), only 5 bits wide (max 31). This causes sparx5_weight_to_hw_cost() to compute cost values that silently overflow via FIELD_PREP, resulting in incorrect scheduling weights. Set SPX5_DWRR_COST_MAX to 31 to match the hardware register width. Fixes: 211225428d65 ("net: microchip: sparx5: add support for offloading ets qdisc") Signed-off-by: Daniel Machon Reviewed-by: Simon Horman Link: https://patch.msgid.link/20260210-sparx5-fix-dwrr-cost-max-v1-1-58fbdbc25652@microchip.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

Merge tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

2025-12-05T01:29:41+00:00

Pull PCI updates from Bjorn Helgaas: "Enumeration: - Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan Williams) - Switch vmd from custom domain number allocator to the common allocator to prevent a potential race with new non-VMD buses (Dan Williams) - Enable Precision Time Measurement (PTM) only if device advertises support for a relevant role, to prevent invalid PTM Requests that cause ACS violations that are reported as AER Uncorrectable Non-Fatal errors (Mika Westerberg) Resource management: - Prevent resource tree corruption when BAR resize fails (Ilpo Järvinen) - Restore BARs to the original size if a BAR resize fails (Ilpo Järvinen) - Remove BAR release from BAR resize attempts by the xe, i915, and amdgpu drivers so the PCI core can restore BARs if the resize fails (Ilpo Järvinen) - Move Resizable BAR code to rebar.c (Ilpo Järvinen) - Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo Järvinen) - Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo Järvinen) Power management and error handling: - For drivers using PCI legacy suspend, save config state at suspend so that state (not any earlier state from enumeration, probe, or error recovery) will be restored when resuming (Lukas Wunner) - For devices with no driver or a driver that lacks power management, save config state at hibernate so that state (not any earlier state from enumeration, probe, or error recovery) will be restored when resuming (Lukas Wunner) - Save device config space on device addition, before driver binding, so error recovery works more reliably (Lukas Wunner) - Drop pci_save_state() from several drivers that no longer need it since the PCI core always does it and pci_restore_state() no longer invalidates the saved state (Lukas Wunner) - Document use of pci_save_state() by drivers to capture the state they want restored during error recovery (Lukas Wunner) Power control: - Add a struct pci_ops.assert_perst() function pointer to assert/deassert PCIe PERST# and implement it for the qcom driver (Krishna Chaitanya Chundru) - Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe switch, which must be held in reset after poweron so the pwrctrl driver can configure the switch via I2C before bringing up the links (Krishna Chaitanya Chundru) Endpoint framework: - Convert the endpoint doorbell test to use a threaded IRQ to fix a 'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri) - Add endpoint VNTB MSI doorbell support to reduce latency between host and endpoint (Frank Li) New native PCIe controller drivers: - Add CIX Sky1 host controller DT binding and driver (Hans Zhang) - Add NXP S32G host controller DT binding and driver (Vincent Guittot) - Add Renesas RZ/G3S host controller DT binding and driver (Claudiu Beznea) - Add SpacemiT K1 host controller DT binding and driver (Alex Elder) Amlogic Meson PCIe controller driver: - Update DT binding to name DBI region 'dbi', not 'elbi', and update driver to support both (Manivannan Sadhasivam) Apple PCIe controller driver: - Move struct pci_host_bridge allocation from pci_host_common_init() to callers, which significantly simplifies pcie-apple (Marc Zyngier) Broadcom STB PCIe controller driver: - Disable advertising ASPM L0s support correctly (Jim Quinlan) - Add a panic/die handler to print diagnostic info in case PCIe caused an unrecoverable abort (Jim Quinlan) Cadence PCIe controller driver: - Add module support for Cadence platform host and endpoint controller driver (Manikandan K Pillai) - Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare for new CIX Sky1 driver (Manikandan K Pillai) MediaTek PCIe controller driver: - Convert DT binding to YAML schema (Christian Marangi) - Add Airoha AN7583 DT compatible and driver support (Christian Marangi) Qualcomm PCIe controller driver: - Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu) - Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280, sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT schemas (Krzysztof Kozlowski) - Look up OPP using both frequency and data rate (not just frequency) so RPMh votes can account for both (Krishna Chaitanya Chundru) Rockchip DesignWare PCIe controller driver: - Add Rockchip RK3528 compatible strings in DT binding (Yao Zi) STMicroelectronics STM32MP25 PCIe controller driver: - Fix a race between link training and endpoint register initialization (Christian Bruel) - Align endpoint allocations to match the ATU requirements (Christian Bruel) Synopsys DesignWare PCIe controller driver: - Clear L1 PM Substate Capability 'Supported' bits unless glue driver says it's supported, which prevents users from enabling non-working L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas) - Remove now-superfluous L1SS disable code from tegra194 (Bjorn Helgaas) - Configure L1SS support in dw-rockchip when DT says 'supports-clkreq' (Shawn Lin) TI Keystone PCIe controller driver: - Fail the probe instead of silently succeeding if ks_pcie_of_data didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli) - Make keystone buildable as a loadable module, except on ARM32 where hook_fault_code() is __init (Siddharth Vadapalli)" * tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits) MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer PCI: sky1: Add PCIe host support for CIX Sky1 dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings PCI: cadence: Add support for High Perf Architecture (HPA) controller MAINTAINERS: Add NXP S32G PCIe controller driver maintainer PCI: s32g: Add NXP S32G PCIe controller driver (RC) PCI: dwc: Add register and bitfield definitions dt-bindings: PCI: s32g: Add NXP S32G PCIe controller PCI: Add Renesas RZ/G3S host controller driver PCI: host-generic: Move bridge allocation outside of pci_host_common_init() dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding PCI: Validate pci_rebar_size_supported() input Documentation: PCI: Amend error recovery doc with pci_save_state() rules treewide: Drop pci_save_state() after pci_restore_state() PCI/ERR: Ensure error recoverability at all times PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths PCI: dw-rockchip: Configure L1SS support PCI: tegra194: Remove unnecessary L1SS disable code ...

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2025-11-27T20:19:08+00:00

Conflicts: net/xdp/xsk.c 0ebc27a4c67d ("xsk: avoid data corruption on cq descriptor number") 8da7bea7db69 ("xsk: add indirect call for xsk_destruct_skb") 30ed05adca4a ("xsk: use a smaller new lock for shared pool case") https://lore.kernel.org/20251127105450.4a1665ec@canb.auug.org.au https://lore.kernel.org/eb4eee14-7e24-4d1b-b312-e9ea738fefee@kernel.org Signed-off-by: Jakub Kicinski

net: lan966x: Fix the initialization of taprio

2025-11-25T14:45:19+00:00

To initialize the taprio block in lan966x, it is required to configure the register REVISIT_DLY. The purpose of this register is to set the delay before revisit the next gate and the value of this register depends on the system clock. The problem is that the we calculated wrong the value of the system clock period in picoseconds. The actual system clock is ~165.617754MHZ and this correspond to a period of 6038 pico seconds and not 15125 as currently set. Fixes: e462b2717380b4 ("net: lan966x: Add offload support for taprio") Signed-off-by: Horatiu Vultur Reviewed-by: Simon Horman Link: https://patch.msgid.link/20251121061411.810571-1-horatiu.vultur@microchip.com Signed-off-by: Paolo Abeni

treewide: Drop pci_save_state() after pci_restore_state()

2025-11-24T22:58:59+00:00

In 2009, commit c82f63e411f1 ("PCI: check saved state before restore") changed the behavior of pci_restore_state() such that it became necessary to call pci_save_state() afterwards, lest recovery from subsequent PCI errors fails. The commit has just been reverted and so all the pci_save_state() after pci_restore_state() calls that have accumulated in the tree are now superfluous. Drop them. Two drivers chose a different approach to achieve the same result: drivers/scsi/ipr.c and drivers/net/ethernet/intel/e1000e/netdev.c set the pci_dev's "state_saved" flag to true before calling pci_restore_state(). Drop this as well. Signed-off-by: Lukas Wunner Signed-off-by: Bjorn Helgaas Acked-by: Dave Jiang Acked-by: Giovanni Cabiddu # qat Link: https://patch.msgid.link/c2b28cc4defa1b743cf1dedee23c455be98b397a.1760274044.git.lukas@wunner.de

net: sparx5/lan969x: populate netdev of_node

2025-11-12T02:06:07+00:00

Populate of_node for the port netdevs, to make the individual ports of_nodes available in sysfs. Signed-off-by: Robert Marko Link: https://patch.msgid.link/20251110124342.199216-1-robert.marko@sartura.hr Signed-off-by: Jakub Kicinski

lan966x: Fix sleeping in atomic context

2025-11-06T15:31:34+00:00

The following warning was seen when we try to connect using ssh to the device. BUG: sleeping function called from invalid context at kernel/locking/mutex.c:575 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 104, name: dropbear preempt_count: 1, expected: 0 INFO: lockdep is turned off. CPU: 0 UID: 0 PID: 104 Comm: dropbear Tainted: G W 6.18.0-rc2-00399-g6f1ab1b109b9-dirty #530 NONE Tainted: [W]=WARN Hardware name: Generic DT based system Call trace: unwind_backtrace from show_stack+0x10/0x14 show_stack from dump_stack_lvl+0x7c/0xac dump_stack_lvl from __might_resched+0x16c/0x2b0 __might_resched from __mutex_lock+0x64/0xd34 __mutex_lock from mutex_lock_nested+0x1c/0x24 mutex_lock_nested from lan966x_stats_get+0x5c/0x558 lan966x_stats_get from dev_get_stats+0x40/0x43c dev_get_stats from dev_seq_printf_stats+0x3c/0x184 dev_seq_printf_stats from dev_seq_show+0x10/0x30 dev_seq_show from seq_read_iter+0x350/0x4ec seq_read_iter from seq_read+0xfc/0x194 seq_read from proc_reg_read+0xac/0x100 proc_reg_read from vfs_read+0xb0/0x2b0 vfs_read from ksys_read+0x6c/0xec ksys_read from ret_fast_syscall+0x0/0x1c Exception stack(0xf0b11fa8 to 0xf0b11ff0) 1fa0: 00000001 00001000 00000008 be9048d8 00001000 00000001 1fc0: 00000001 00001000 00000008 00000003 be905920 0000001e 00000000 00000001 1fe0: 0005404c be9048c0 00018684 b6ec2cd8 It seems that we are using a mutex in a atomic context which is wrong. Change the mutex with a spinlock. Fixes: 12c2d0a5b8e2 ("net: lan966x: add ethtool configuration and statistics") Signed-off-by: Horatiu Vultur Reviewed-by: Jacob Keller Link: https://patch.msgid.link/20251105074955.1766792-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski

net: sparx5/lan969x: fix flooding configuration on bridge join/leave

2025-10-07T09:53:45+00:00

The sparx5 driver programs UC/MC/BC flooding in sparx5_update_fwd() by unconditionally applying bridge_fwd_mask to all flood PGIDs. Any bridge topology change that triggers sparx5_update_fwd() (for example enslaving another port) therefore reinstalls flooding in hardware for already bridged ports, regardless of their per-port flood flags. This results in clobbering of the flood masks, and desynchronization between software and hardware: the bridge still reports “flood off” for the port, but hardware has flooding enabled due to unconditional PGID reprogramming. Steps to reproduce: $ ip link add br0 type bridge $ ip link set br0 up $ ip link set eth0 master br0 $ ip link set eth0 up $ bridge link set dev eth0 flood off $ ip link set eth1 master br0 $ ip link set eth1 up At this point, flooding is silently re-enabled for eth0. Software still shows “flood off” for eth0, but hardware has flooding enabled. To fix this, flooding is now set explicitly during bridge join/leave, through sparx5_port_attr_bridge_flags(): On bridge join, UC/MC/BC flooding is enabled by default. On bridge leave, UC/MC/BC flooding is disabled. sparx5_update_fwd() no longer touches the flood PGIDs, clobbering the flood masks, and desynchronizing software and hardware. Initialization of the flooding PGIDs have been moved to sparx5_start(). This is required as flooding PGIDs defaults to 0x3fffffff in hardware and the initialization was previously handled in sparx5_update_fwd(), which was removed. With this change, user-configured flooding flags persist across bridge updates and are no longer overridden by sparx5_update_fwd(). Fixes: d6fce5141929 ("net: sparx5: add switching support") Signed-off-by: Daniel Machon Reviewed-by: Simon Horman Link: https://patch.msgid.link/20251003-fix-flood-fwd-v1-1-48eb478b2904@microchip.com Signed-off-by: Paolo Abeni