kernel/linux.git/drivers/net/dsa, branch v6.1.168

net: dsa: bcm_sf2: fix missing clk_disable_unprepare() in error paths

2026-03-25T10:03:22+00:00

[ Upstream commit b48731849609cbd8c53785a48976850b443153fd ] Smatch reports: drivers/net/dsa/bcm_sf2.c:997 bcm_sf2_sw_resume() warn: 'priv->clk' from clk_prepare_enable() not released on lines: 983,990. The clock enabled by clk_prepare_enable() in bcm_sf2_sw_resume() is not released if bcm_sf2_sw_rst() or bcm_sf2_cfp_resume() fails. Add the missing clk_disable_unprepare() calls in the error paths to properly release the clock resource. Fixes: e9ec5c3bd238 ("net: dsa: bcm_sf2: request and handle clocks") Reviewed-by: Jonas Gorski Reviewed-by: Florian Fainelli Signed-off-by: Anas Iqbal Link: https://patch.msgid.link/20260318084212.1287-1-mohd.abd.6602@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: dsa: realtek: rtl8365mb: remove ifOutDiscards from rx_packets

2026-03-25T10:03:03+00:00

[ Upstream commit f76a93241d71fbba8425e3967097b498c29264ed ] rx_packets should report the number of frames successfully received: unicast + multicast + broadcast. Subtracting ifOutDiscards (a TX counter) is incorrect and can undercount RX packets. RX drops are already reported via rx_dropped (e.g. etherStatsDropEvents), so there is no need to adjust rx_packets. This patch removes the subtraction of ifOutDiscards from rx_packets in rtl8365mb_stats_update(). Link: https://lore.kernel.org/netdev/878777925.105015.1763423928520@mail.yahoo.com/ Fixes: 4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC") Signed-off-by: Mieczyslaw Nalewaj Signed-off-by: Luiz Angelo Daros de Luca Reviewed-by: Simon Horman Acked-by: Linus Walleij Link: https://patch.msgid.link/20260303-realtek_namiltd_fix2-v1-1-bfa433d3401e@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: dsa: realtek: rtl8365mb: fix rtl8365mb_phy_ocp_write return value

2026-03-25T10:03:00+00:00

[ Upstream commit 7cbe98f7bef965241a5908d50d557008cf998aee ] Function rtl8365mb_phy_ocp_write() always returns 0, even when an error occurs during register access. This patch fixes the return value to propagate the actual error code from regmap operations. Link: https://lore.kernel.org/netdev/a2dfde3c-d46f-434b-9d16-1e251e449068@yahoo.com/ Fixes: 2796728460b8 ("net: dsa: realtek: rtl8365mb: serialize indirect PHY register access") Signed-off-by: Mieczyslaw Nalewaj Reviewed-by: Andrew Lunn Signed-off-by: Luiz Angelo Daros de Luca Reviewed-by: Linus Walleij Link: https://patch.msgid.link/20260301-realtek_namiltd_fix1-v1-1-43a6bb707f9c@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: dsa: sja1105: fix kasan out-of-bounds warning in sja1105_table_delete_entry()

2026-01-11T14:19:15+00:00

[ Upstream commit 5f2b28b79d2d1946ee36ad8b3dc0066f73c90481 ] There are actually 2 problems: - deleting the last element doesn't require the memmove of elements [i + 1, end) over it. Actually, element i+1 is out of bounds. - The memmove itself should move size - i - 1 elements, because the last element is out of bounds. The out-of-bounds element still remains out of bounds after being accessed, so the problem is only that we touch it, not that it becomes in active use. But I suppose it can lead to issues if the out-of-bounds element is part of an unmapped page. Fixes: 6666cebc5e30 ("net: dsa: sja1105: Add support for VLAN operations") Signed-off-by: Vladimir Oltean Reviewed-by: Simon Horman Link: https://patch.msgid.link/20250318115716.2124395-4-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski Signed-off-by: Chen Yu Signed-off-by: Greg Kroah-Hartman

net: dsa: b53: skip multicast entries for fdb_dump()

2026-01-11T14:19:01+00:00

[ Upstream commit d42bce414d1c5c0b536758466a1f63ac358e613c ] port_fdb_dump() is supposed to only add fdb entries, but we iterate over the full ARL table, which also includes multicast entries. So check if the entry is a multicast entry before passing it on to the callback(). Additionally, the port of those entries is a bitmask, not a port number, so any included entries would have even be for the wrong port. Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by: Jonas Gorski Reviewed-by: Florian Fainelli Link: https://patch.msgid.link/20251217205756.172123-1-jonas.gorski@gmail.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: dsa: microchip: common: Fix checks on irq_find_mapping()

2025-12-06T21:12:44+00:00

commit 7b3c09e1667977edee11de94a85e2593a7c15e87 upstream. irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found but it never returns a negative value. However, on each irq_find_mapping() call, we verify that the returned value isn't negative. Fix the irq_find_mapping() checks to enter error paths when 0 is returned. Return -EINVAL in such cases. CC: stable@vger.kernel.org Fixes: c9cd961c0d43 ("net: dsa: microchip: lan937x: add interrupt support for port phy link") Reviewed-by: Andrew Lunn Signed-off-by: Bastien Curutchet (Schneider Electric) Link: https://patch.msgid.link/20251120-ksz-fix-v6-1-891f80ae7f8f@bootlin.com Signed-off-by: Paolo Abeni Signed-off-by: Greg Kroah-Hartman

net: dsa: sja1105: fix SGMII linking at 10M or 100M but not passing traffic

2025-12-06T21:12:41+00:00

[ Upstream commit da62abaaa268357b1aa66b372ace562189a05df1 ] When using the SGMII PCS as a fixed-link chip-to-chip connection, it is easy to miss the fact that traffic passes only at 1G, since that's what any normal such connection would use. When using the SGMII PCS connected towards an on-board PHY or an SFP module, it is immediately noticeable that when the link resolves to a speed other than 1G, traffic from the MAC fails to pass: TX counters increase, but nothing gets decoded by the other end, and no local RX counters increase either. Artificially lowering a fixed-link rate to speed = <100> makes us able to see the same issue as in the case of having an SGMII PHY. Some debugging shows that the XPCS configuration is A-OK, but that the MAC Configuration Table entry for the port has the SPEED bits still set to 1000Mbps, due to a special condition in the driver. Deleting that condition, and letting the resolved link speed be programmed directly into the MAC speed field, results in a functional link at all 3 speeds. This piece of evidence, based on testing on both generations with SGMII support (SJA1105S and SJA1110A) directly contradicts the statement from the blamed commit that "the MAC is fixed at 1 Gbps and we need to configure the PCS only (if even that)". Worse, that statement is not backed by any documentation, and no one from NXP knows what it might refer to. I am unable to recall sufficient context regarding my testing from March 2020 to understand what led me to draw such a braindead and factually incorrect conclusion. Yet, there is nothing of value regarding forcing the MAC speed, either for SGMII or 2500Base-X (introduced at a later stage), so remove all such logic. Fixes: ffe10e679cec ("net: dsa: sja1105: Add support for the SGMII port") Signed-off-by: Vladimir Oltean Link: https://patch.msgid.link/20251122111324.136761-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: dsa: sja1105: simplify static configuration reload

2025-12-06T21:12:41+00:00

[ Upstream commit a18891b55703a45b700618ef40edd5e9aaecc345 ] The static configuration reload saves the port speed in the static configuration tables by first converting it from the internal respresentation to the SPEED_xxx ethtool representation, and then converts it back to restore the setting. This is because sja1105_adjust_port_config() takes the speed as SPEED_xxx. However, this is unnecessarily complex. If we split sja1105_adjust_port_config() up, we can simply save and restore the mac[port].speed member in the static configuration tables. Signed-off-by: Russell King (Oracle) Link: https://patch.msgid.link/E1svfMa-005ZIX-If@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski Stable-dep-of: da62abaaa268 ("net: dsa: sja1105: fix SGMII linking at 10M or 100M but not passing traffic") Signed-off-by: Sasha Levin

net: dsa: hellcreek: fix missing error handling in LED registration

2025-12-06T21:12:38+00:00

[ Upstream commit e6751b0b19a6baab219a62e1e302b8aa6b5a55b2 ] The LED setup routine registered both led_sync_good and led_is_gm devices without checking the return values of led_classdev_register(). If either registration failed, the function continued silently, leaving the driver in a partially-initialized state and leaking a registered LED classdev. Add proper error handling Fixes: 7d9ee2e8ff15 ("net: dsa: hellcreek: Add PTP status LEDs") Signed-off-by: Pavel Zhigulin Reviewed-by: Andrew Lunn Acked-by: Kurt Kanzenbach Link: https://patch.msgid.link/20251113135745.92375-1-Pavel.Zhigulin@kaspersky.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: dsa: microchip: lan937x: Fix RGMII delay tuning

2025-12-06T21:12:37+00:00

commit 3ceb6ac2116ecda1c5d779bb73271479e70fccb4 upstream. Correct RGMII delay application logic in lan937x_set_tune_adj(). The function was missing `data16 &= ~PORT_TUNE_ADJ` before setting the new delay value. This caused the new value to be bitwise-OR'd with the existing PORT_TUNE_ADJ field instead of replacing it. For example, when setting the RGMII 2 TX delay on port 4, the intended TUNE_ADJUST value of 0 (RGMII_2_TX_DELAY_2NS) was incorrectly OR'd with the default 0x1B (from register value 0xDA3), leaving the delay at the wrong setting. This patch adds the missing mask to clear the field, ensuring the correct delay value is written. Physical measurements on the RGMII TX lines confirm the fix, showing the delay changing from ~1ns (before change) to ~2ns. While testing on i.MX 8MP showed this was within the platform's timing tolerance, it did not match the intended hardware-characterized value. Fixes: b19ac41faa3f ("net: dsa: microchip: apply rgmii tx and rx delay in phylink mac config") Cc: stable@vger.kernel.org Signed-off-by: Oleksij Rempel Link: https://patch.msgid.link/20251114090951.4057261-1-o.rempel@pengutronix.de Signed-off-by: Paolo Abeni Signed-off-by: Greg Kroah-Hartman