kernel/linux.git/drivers/net/dsa, branch v5.4.113

net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits

2021-04-14T06:24:13+00:00

commit 4b5923249b8fa427943b50b8f35265176472be38 upstream. There are a few more bits in the GSWIP_MII_CFG register for which we did rely on the boot-loader (or the hardware defaults) to set them up properly. For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK bit and also we should un-set it for non-RMII PHYs. The GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes. The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's no known hardware which uses this (so it is not tested yet). Clear the xMII isolation bit when set at initialization time if it was previously set by the bootloader. Not doing so could lead to no traffic (neither RX nor TX) on a port with this bit set. While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to manage it because this bit is self-clearning when set. We still add it here to get a better overview of the GSWIP_MII_CFG register. Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Cc: stable@vger.kernel.org Suggested-by: Hauke Mehrtens Acked-by: Hauke Mehrtens Signed-off-by: Martin Blumenstingl Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman [ Updated after the upstream commit 3e9005be87777 required some changes for Linux 5.4 ] Signed-off-by: Martin Blumenstingl Signed-off-by: Sasha Levin

net: dsa: lantiq_gswip: Don't use PHY auto polling

2021-04-14T06:24:13+00:00

commit 3e9005be87777afc902b9f5497495898202d335d upstream. PHY auto polling on the GSWIP hardware can be used so link changes (speed, link up/down, etc.) can be detected automatically. Internally GSWIP reads the PHY's registers for this functionality. Based on this automatic detection GSWIP can also automatically re-configure it's port settings. Unfortunately this auto polling (and configuration) mechanism seems to cause various issues observed by different people on different devices: - FritzBox 7360v2: the two Gbit/s ports (connected to the two internal PHY11G instances) are working fine but the two Fast Ethernet ports (using an AR8030 RMII PHY) are completely dead (neither RX nor TX are received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This makes the PHY auto polling state machine (rightfully?) think that the established link speed (when the other side is Gbit/s capable) is 1Gbit/s. - None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are connected to the internal PHY11G GPHYs while the other three are external RGMII PHYs) are working. Neither RX nor TX traffic was observed. It is not clear which part of the PHY auto polling state- machine caused this. - FritzBox 7412 (only one LAN port which is connected to one of the internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing random disconnects (link down events could be seen). Sometimes all traffic would stop after such disconnect. It is not clear which part of the PHY auto polling state-machine cauased this. - TP-Link TD-W9980 (two ports are connected to the internal GPHYs running in PHY11G / Gbit/s mode, the other two are external RGMII PHYs) was affected by similar issues as the FritzBox 7412 just without the "link down" events Switch to software based configuration instead of PHY auto polling (and letting the GSWIP hardware configure the ports automatically) for the following link parameters: - link up/down - link speed - full/half duplex - flow control (RX / TX pause) After a big round of manual testing by various people (who helped test this on OpenWrt) it turns out that this fixes all reported issues. Additionally it can be considered more future proof because any "quirk" which is implemented for a PHY on the driver side can now be used with the GSWIP hardware as well because Linux is in control of the link parameters. As a nice side-effect this also solves a problem where fixed-links were not supported previously because we were relying on the PHY auto polling mechanism, which cannot work for fixed-links as there's no PHY from where it can read the registers. Configuring the link settings on the GSWIP ports means that we now use the settings from device-tree also for ports with fixed-links. Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock") Cc: stable@vger.kernel.org Acked-by: Hauke Mehrtens Reviewed-by: Andrew Lunn Signed-off-by: Martin Blumenstingl Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman [ Move gswip_port_set_{speed, duplex, pause} calls from gswip_phylink_mac_link_up to gswip_phylink_mac_config because the data required for these functions is not available inside gswip_phylink_mac_link_up yet in Linux 5.4 (it was only added with Linux 5.7). ] Signed-off-by: Martin Blumenstingl Signed-off-by: Sasha Levin

net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock

2021-04-14T06:24:10+00:00

commit 3e6fdeb28f4c331acbd27bdb0effc4befd4ef8e8 upstream. The xMII interface clock depends on the PHY interface (MII, RMII, RGMII) as well as the current link speed. Explicitly configure the GSWIP to automatically select the appropriate xMII interface clock. This fixes an issue seen by some users where ports using an external RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most likely this is due to an "invalid" xMII clock being selected either by the bootloader or hardware-defaults. Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Signed-off-by: Martin Blumenstingl Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: dsa: b53: VLAN filtering is global to all users

2021-03-30T12:35:29+00:00

commit d45c36bafb94e72fdb6dee437279b61b6d97e706 upstream. The bcm_sf2 driver uses the b53 driver as a library but does not make usre of the b53_setup() function, this made it fail to inherit the vlan_filtering_is_global attribute. Fix this by moving the assignment to b53_switch_alloc() which is used by bcm_sf2. Fixes: 7228b23e68f7 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: dsa: bcm_sf2: Qualify phydev->dev_flags based on port

2021-03-30T12:35:25+00:00

[ Upstream commit 47142ed6c34d544ae9f0463e58d482289cbe0d46 ] Similar to commit 92696286f3bb37ba50e4bd8d1beb24afb759a799 ("net: bcmgenet: Set phydev->dev_flags only for internal PHYs") we need to qualify the phydev->dev_flags based on whether the port is connected to an internal or external PHY otherwise we risk having a flags collision with a completely different interpretation depending on the driver. Fixes: aa9aef77c761 ("net: dsa: bcm_sf2: communicate integrated PHY revision to PHY driver") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: dsa: b53: Support setting learning on port

2021-03-20T09:39:47+00:00

commit f9b3827ee66cfcf297d0acd6ecf33653a5f297ef upstream. Add support for being able to set the learning attribute on port, and make sure that the standalone ports start up with learning disabled. We can remove the code in bcm_sf2 that configured the ports learning attribute because we want the standalone ports to have learning disabled by default and port 7 cannot be bridged, so its learning attribute will not change past its initial configuration. Signed-off-by: Florian Fainelli Reviewed-by: Vladimir Oltean Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: mv88e6xxx: override existent unicast portvec in port_fdb_add

2021-02-10T08:25:33+00:00

commit f72f2fb8fb6be095b98af5d740ac50cffd0b0cae upstream. Having multiple destination ports for a unicast address does not make sense. Make port_db_load_purge override existent unicast portvec instead of adding a new port bit. Fixes: 884729399260 ("net: dsa: mv88e6xxx: handle multiple ports in ATU") Signed-off-by: DENG Qingfang Reviewed-by: Vladimir Oltean Link: https://lore.kernel.org/r/20210130134334.10243-1-dqfext@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: bcm_sf2: put device node before return

2021-02-07T14:35:46+00:00

commit cf3c46631e1637582f517a574c77cd6c05793817 upstream. Put the device node dn before return error code on failure path. Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus") Signed-off-by: Pan Bian Link: https://lore.kernel.org/r/20210121123343.26330-1-bianpan2016@163.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: b53: fix an off by one in checking "vlan->vid"

2021-01-27T10:47:55+00:00

commit 8e4052c32d6b4b39c1e13c652c7e33748d447409 upstream. The > comparison should be >= to prevent accessing one element beyond the end of the dev->vlans[] array in the caller function, b53_vlan_add(). The "dev->vlans" array is allocated in the b53_switch_init() function and it has "dev->num_vlans" elements. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Dan Carpenter Acked-by: Florian Fainelli Link: https://lore.kernel.org/r/YAbxI97Dl/pmBy5V@mwanda Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: mv88e6xxx: also read STU state in mv88e6250_g1_vtu_getnext

2021-01-27T10:47:52+00:00

commit 87fe04367d842c4d97a77303242d4dd4ac351e46 upstream. mv88e6xxx_port_vlan_join checks whether the VTU already contains an entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely changes the relevant .member[] element and loads the updated entry into the VTU. However, at least for the mv88e6250, the on-stack struct mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly initialized, neither in mv88e6xxx_port_vlan_join() nor inside the getnext implementation. So the new entry has random garbage for the STU bits, breaking VLAN filtering. When the VTU entry is initially created, those bits are all zero, and we should make sure to keep them that way when the entry is updated. Fixes: 92307069a96c (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097) Signed-off-by: Rasmus Villemoes Reviewed-by: Florian Fainelli Reviewed-by: Tobias Waldekranz Tested-by: Tobias Waldekranz Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman