kernel/linux.git/drivers/net/dsa/Makefile, branch v6.12.80

net: dsa: mt7530: introduce driver for MT7988 built-in switch

2023-04-03T09:13:01+00:00

Add driver for the built-in Gigabit Ethernet switch which can be found in the MediaTek MT7988 SoC. The switch shares most of its design with MT7530 and MT7531, but has it's registers mapped into the SoCs register space rather than being connected externally or internally via MDIO. Introduce a new platform driver to support that. Signed-off-by: Daniel Golle Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: dsa: mt7530: introduce separate MDIO driver

2023-04-03T09:13:00+00:00

Split MT7530 switch driver into a common part and a part specific for MDIO connected switches and multi-chip modules. Move MDIO-specific functions to newly introduced mt7530-mdio.c while keeping the common parts in mt7530.c. Introduce new Kconfig symbol CONFIG_NET_DSA_MT7530_MDIO which is implied by CONFIG_NET_DSA_MT7530. Signed-off-by: Daniel Golle Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: dsa: qca8k: move driver to qca dir

2022-07-15T10:57:13+00:00

Move qca8k driver to qca dir in preparation for code split and introduction of ipq4019 switch based on qca8k. Signed-off-by: Christian Marangi Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver

2022-06-27T10:37:55+00:00

Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5 ports including 1 CPU management port. A MDIO bus is also exposed by this switch and allows to communicate with PHYs connected to the ports. Each switch port (except for the CPU management ports) is connected to the MII converter. This driver includes basic bridging support, more support will be added later (vlan, etc). Suggested-by: Jean-Pierre Geslin Suggested-by: Phil Edworthy Signed-off-by: Clément Léger Reviewed-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: dsa: realtek-smi: move to subdirectory

2022-01-28T15:02:49+00:00

Signed-off-by: Luiz Angelo Daros de Luca Tested-by: Arınç ÜNAL Reviewed-by: Alvin Šipraga Reviewed-by: Linus Walleij Reviewed-by: Florian Fainelli Reviewed-by: Vladimir Oltean Signed-off-by: David S. Miller

net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC

2021-10-18T13:02:56+00:00

This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port 10/100/1000M switch controller. The driver has been developed based on a GPL-licensed OS-agnostic Realtek vendor driver known as rtl8367c found in the OpenWrt source tree. Despite the name, the RTL8365MB-VC has an entirely different register layout to the already-supported RTL8366RB ASIC. Notwithstanding this, the structure of the rtl8365mb subdriver is loosely based on the rtl8366rb subdriver. Like the 'rb, it establishes its own irqchip to handle cascaded PHY link status interrupts. The RTL8365MB-VC switch is capable of offloading a large number of features from the software, but this patch introduces only the most basic DSA driver functionality. The ports always function as standalone ports, with bridging handled in software. One more thing. Realtek's nomenclature for switches makes it hard to know exactly what other ASICs might be supported by this driver. The vendor driver goes by the name rtl8367c, but as far as I can tell, no chip actually exists under this name. As such, the subdriver is named rtl8365mb to emphasize the potentially limited support. But it is clear from the vendor sources that a number of other more advanced switches share a similar register layout, and further support should not be too hard to add given access to the relevant hardware. With this in mind, the subdriver has been written with as few assumptions about the particular chip as is reasonable. But the RTL8365MB-VC is the only hardware I have available, so some further work is surely needed. Co-developed-by: Michael Rasmussen Signed-off-by: Michael Rasmussen Signed-off-by: Alvin Šipraga Reviewed-by: Vladimir Oltean Reviewed-by: Linus Walleij Reviewed-by: Florian Fainelli Tested-by: Arınç ÜNAL Signed-off-by: David S. Miller

net: dsa: add Arrow SpeedChips XRS700x driver

2021-01-15T23:37:37+00:00

Add a driver with initial support for the Arrow SpeedChips XRS7000 series of gigabit Ethernet switch chips which are typically used in critical networking applications. The switches have up to three RGMII ports and one RMII port. Management to the switches can be performed over i2c or mdio. Support for advanced features such as PTP and HSR/PRP (IEC 62439-3 Clause 5 & 4) is not included in this patch and may be added at a later date. Signed-off-by: George McCollister Reviewed-by: Florian Fainelli Reviewed-by: Andrew Lunn Reviewed-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: dsa: Add DSA driver for Hirschmann Hellcreek switches

2020-11-05T22:04:49+00:00

Add a basic DSA driver for Hirschmann Hellcreek switches. Those switches are implementing features needed for Time Sensitive Networking (TSN) such as support for the Time Precision Protocol and various shapers like the Time Aware Shaper. This driver includes basic support for networking: * VLAN handling * FDB handling * Port statistics * STP * Phylink Signed-off-by: Kurt Kanzenbach Reviewed-by: Vladimir Oltean Reviewed-by: Florian Fainelli Signed-off-by: Jakub Kicinski

net: dsa: add support for Atheros AR9331 built-in switch

2019-12-21T01:05:47+00:00

Provide basic support for Atheros AR9331 built-in switch. So far it works as port multiplexer without any hardware offloading support. Reviewed-by: Andrew Lunn Reviewed-by: Vivien Didelot Signed-off-by: Oleksij Rempel Signed-off-by: David S. Miller

net: dsa: ocelot: add driver for Felix switch family

2019-11-15T20:32:16+00:00

This supports an Ethernet switching core from Vitesse / Microsemi / Microchip (VSC9959) which is part of the Ocelot family (a brand name), and whose code name is Felix. The switch can be (and is) integrated on different SoCs as a PCIe endpoint device. The functionality is provided by the core of the Ocelot switch driver (drivers/net/ethernet/mscc). In this regard, the current driver is an instance of Microsemi's Ocelot core driver, with a DSA front-end. It inherits its name from VSC9959's code name, to distinguish itself from the switchdev ocelot driver. The patch adds the logic for probing a PCI device and defines the register map for the VSC9959 switch core, since it has some differences in register addresses and bitfield mappings compared to the other Ocelot switches (VSC7511, VSC7512, VSC7513, VSC7514). The Felix driver declares the register map as part of the "instance table". Currently the VSC9959 inside NXP LS1028A is the only instance, but presumably it can support other switches in the Ocelot family, when used in DSA mode (Linux running on the external CPU, and not on the embedded MIPS). In a few cases, some h/w operations have to be done differently on VSC9959 due to missing bitfields. This is the case for the switch core reset and init. Because for this operation Ocelot uses some bits that are not present on Felix, the latter has to use a register from the global registers block (GCB) instead. Although it is a PCI driver, it relies on DT bindings for compatibility with DSA (CPU port link, PHY library). It does not have any custom device tree bindings, since we would like to minimize its dependency on device tree though. Signed-off-by: Claudiu Manoil Signed-off-by: Vladimir Oltean Signed-off-by: David S. Miller