kernel/linux.git/drivers/net/can/Makefile, branch v6.6.132

can: bxcan: add support for ST bxCAN controller

2023-03-28T09:43:36+00:00

Add support for the basic extended CAN controller (bxCAN) found in many low- to middle-end STM32 SoCs. It supports the Basic Extended CAN protocol versions 2.0A and B with a maximum bit rate of 1 Mbit/s. The controller supports two channels (CAN1 as primary and CAN2 as secondary) and the driver can enable either or both of the channels. They share some of the required logic (e. g. clocks and filters), and that means you cannot use the secondary CAN without enabling some hardware resources managed by the primary CAN. Each channel has 3 transmit mailboxes, 2 receive FIFOs with 3 stages and 28 scalable filter banks. It also manages 4 dedicated interrupt vectors: - transmit interrupt - FIFO 0 receive interrupt - FIFO 1 receive interrupt - status change error interrupt Driver uses all 3 available mailboxes for transmission and FIFO 0 for reception. Rx filter rules are configured to the minimum. They accept all messages and assign filter 0 to CAN1 and filter 14 to CAN2 in identifier mask mode with 32 bits width. It enables and uses transmit, receive buffers for FIFO 0 and error and status change interrupts. Signed-off-by: Dario Binacchi Reviewed-by: Vincent Mailhol Link: https://lore.kernel.org/all/20230328073328.3949796-6-dario.binacchi@amarulasolutions.com Signed-off-by: Marc Kleine-Budde

can: remove obsolete PCH CAN driver

2022-10-19T19:33:30+00:00

The PCH CAN driver is a driver for a Bosch C_CAN controller IP core which is attached to the system via PCI. This code has been introduced in 2011 by Oki Semiconductors developers to support the Intel Atom E6xx series I/O Hub (aka EG20T IOH PCH CAN). Since 2012 the driver only has been maintained by the kernel community. As there is a well maintained and continously tested C_CAN/D_CAN driver which also supports the PCI configuration from the PCH CAN EG20T setup this driver became obsolete. Cc: Jacob Kroon Cc: Marc Kleine-Budde Cc: Dario Binacchi Cc: Wolfgang Grandegger Signed-off-by: Oliver Hartkopp Link: https://lore.kernel.org/all/20220924174424.86541-1-socketcan@hartkopp.net Acked-by: Jacob Kroon Signed-off-by: Marc Kleine-Budde

can: slcan: move driver into separate sub directory

2022-07-03T09:34:44+00:00

This patch moves the slcan driver into a separate directory, a later patch will add more files. Link: https://lore.kernel.org/all/20220628163137.413025-10-dario.binacchi@amarulasolutions.com Signed-off-by: Dario Binacchi Signed-off-by: Marc Kleine-Budde

can: can327: CAN/ldisc driver for ELM327 based OBD-II adapters

2022-06-27T15:00:04+00:00

This is the can327 driver. It does a surprisingly good job at turning ELM327 based OBD-II interfaces into cheap CAN interfaces for simple homebrew projects. Please see the included documentation for details and limitations: Documentation/networking/device_drivers/can/can327.rst Link: https://lore.kernel.org/all/20220618195031.10975-1-max@enpas.org Signed-off-by: Max Staudt Reviewed-by: Vincent Mailhol [mkl: minor coding style improvements] Signed-off-by: Marc Kleine-Budde

can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.

2022-04-19T15:12:14+00:00

This driver adds support for the CTU CAN FD open-source IP core. More documentation and core sources at project page (https://gitlab.fel.cvut.cz/canbus/ctucanfd_ip_core). The core integration to Xilinx Zynq system as platform driver is available (https://gitlab.fel.cvut.cz/canbus/zynq/zynq-can-sja1000-top). Implementation on Intel FPGA based PCI Express board is available from project (https://gitlab.fel.cvut.cz/canbus/pcie-ctucanfd). More about CAN bus related projects used and developed at CTU FEE at https://canbus.pages.fel.cvut.cz/ . Link: https://lore.kernel.org/all/1906e4941560ae2ce4b8d181131fd4963aa31611.1647904780.git.pisa@cmp.felk.cvut.cz Signed-off-by: Martin Jerabek Signed-off-by: Ondrej Ille Signed-off-by: Pavel Pisa Signed-off-by: Marc Kleine-Budde

can: flexcan: move driver into separate sub directory

2022-01-08T19:17:42+00:00

This patch moves the flexcan driver into a separate directory, a later patch will add more files. Link: https://lore.kernel.org/all/20220107193105.1699523-2-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde

can: dev: move driver related infrastructure into separate subdir

2021-01-13T08:42:58+00:00

This patch moves the CAN driver related infrastructure into a separate subdir. It will be split into more files in the coming patches. Reviewed-by: Vincent Mailhol Link: https://lore.kernel.org/r/20210111141930.693847-3-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde

can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices

2019-07-24T08:31:53+00:00

This patch adds support for Kvaser PCIEcan devices. This includes support for up to 4 CAN channels on a single card, depending on device. Signed-off-by: Henning Colliander Signed-off-by: Jimmy Assarsson Signed-off-by: Christer Beskow Signed-off-by: Marc Kleine-Budde

can: remove bfin_can driver

2018-03-26T13:57:02+00:00

The blackfin architecture is getting removed, so this one is now obsolete. Acked-by: Aaron Wu Signed-off-by: Arnd Bergmann

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55+00:00

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman