kernel/linux.git/drivers/mtd/devices, branch v4.19.112

mtd: devices: fix mchp23k256 read and write

2020-01-23T07:21:37+00:00

commit 14f89e088155314d311e4d4dd9f2b4ccaeef92b2 upstream. Due to the use of sizeof(), command size set for the spi transfer was wrong. Driver was sending and receiving always 1 byte less and especially on write, it was hanging. echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1 And read part too now works as expected. hexdump -C -n16 /dev/mtd1 00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15 00000010 Fixes: 4379075a870b ("mtd: mchp23k256: Add support for mchp23lcv1024") Signed-off-by: Angelo Dureghello Reviewed-by: Andrew Lunn Signed-off-by: Miquel Raynal Signed-off-by: Greg Kroah-Hartman

mtd: spear_smi: Fix Write Burst mode

2019-12-17T19:34:42+00:00

commit 69c7f4618c16b4678f8a4949b6bb5ace259c0033 upstream. Any write with either dd or flashcp to a device driven by the spear_smi.c driver will pass through the spear_smi_cpy_toio() function. This function will get called for chunks of up to 256 bytes. If the amount of data is smaller, we may have a problem if the data length is not 4-byte aligned. In this situation, the kernel panics during the memcpy: # dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6 spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256 spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256 spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256 spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233 Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8 [...] PC is at memcpy+0xcc/0x330 The above error occurs because the implementation of memcpy_toio() tries to optimize the number of I/O by writing 4 bytes at a time as much as possible, until there are less than 4 bytes left and then switches to word or byte writes. Unfortunately, the specification states about the Write Burst mode: "the next AHB Write request should point to the next incremented address and should have the same size (byte, half-word or word)" This means ARM architecture implementation of memcpy_toio() cannot reliably be used blindly here. Workaround this situation by update the write path to stick to byte access when the burst length is not multiple of 4. Fixes: f18dbbb1bfe0 ("mtd: ST SPEAr: Add SMI driver for serial NOR flash") Cc: Russell King Cc: Boris Brezillon Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal Reviewed-by: Russell King Signed-off-by: Greg Kroah-Hartman

mtd: devices: m25p80: Make sure WRITE_EN is issued before each write

2019-11-24T07:20:41+00:00

[ Upstream commit 3baa8ec88c2feb902328e59a4dcf0f0aaab7d2ff ] Some SPI controllers can't write nor->page_size bytes in a single step because their TX FIFO is too small, but when that happens we should make sure a WRITE_EN command before each write access and READ_SR command after each write access is issued. The core is already taking care of that, so all we have to do here is return the actual number of bytes that were written during the spi_mem_exec_op() operation. Signed-off-by: Yogesh Gaur Signed-off-by: Boris Brezillon Signed-off-by: Sasha Levin

mtd: docg3: don't set conflicting BCH_CONST_PARAMS option

2018-11-21T08:19:19+00:00

commit be2e1c9dcf76886a83fb1c433a316e26d4ca2550 upstream. I noticed during the creation of another bugfix that the BCH_CONST_PARAMS option that is set by DOCG3 breaks setting variable parameters for any other users of the BCH library code. The only other user we have today is the MTD_NAND software BCH implementation (most flash controllers use hardware BCH these days and are not affected). I considered removing BCH_CONST_PARAMS entirely because of the inherent conflict, but according to the description in lib/bch.c there is a significant performance benefit in keeping it. To avoid the immediate problem of the conflict between MTD_NAND_BCH and DOCG3, this only sets the constant parameters if MTD_NAND_BCH is disabled, which should fix the problem for all cases that are affected. This should also work for all stable kernels. Note that there is only one machine that actually seems to use the DOCG3 driver (arch/arm/mach-pxa/mioa701.c), so most users should have the driver disabled, but it almost certainly shows up if we wanted to test random kernels on machines that use software BCH in MTD. Fixes: d13d19ece39f ("mtd: docg3: add ECC correction code") Cc: stable@vger.kernel.org Cc: Robert Jarzmik Signed-off-by: Arnd Bergmann Signed-off-by: Boris Brezillon Signed-off-by: Greg Kroah-Hartman

mtd: devices: m25p80: Make sure the buffer passed in op is DMA-able

2018-09-18T08:17:48+00:00

As documented in spi-mem.h, spi_mem_op->data.buf.{in,out} must be DMA-able, and commit 4120f8d158ef ("mtd: spi-nor: Use the spi_mem_xx() API") failed to follow this rule as buffers passed to ->{read,write}_reg() are usually placed on the stack. Fix that by allocating a scratch buffer and copying the data around. Fixes: 4120f8d158ef ("mtd: spi-nor: Use the spi_mem_xx() API") Reported-by: Jarkko Nikula Cc: Signed-off-by: Boris Brezillon Tested-by: Jarkko Nikula Reviewed-by: Jarkko Nikula

Merge tag 'spi-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

2018-08-14T19:01:08+00:00

Pull spi updates from Mark Brown: "Quite an active release for the SPI subsystem, lots of small updates and fixes scattered about with highlights including: - 3-wire support in the GPIO driver. - support for setting a custom memory name in the memory mapped flash drivers. - support for extended mode in the Freescale DSPI controller. - support for the non-standard integration with the Microsemi Ocelot platform in the DesignWare driver. - new driver for the SocioNext UniPhier" * tag 'spi-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (47 commits) spi: davinci: fix a NULL pointer dereference spi: spi-mem: Constify spi_mem->name mtd: m25p80: Call spi_mem_get_name() to let controller set a custom name spi: spi-mem: Extend the SPI mem interface to set a custom memory name spi: spi-mem: Fix a typo in the documentation of struct spi_mem spi: uniphier: remove unnecessary include headers spi: spi-gpio: add SPI_3WIRE support spi: add flags parameter to txrx_word function pointers spi: add SPI controller driver for UniPhier SoC spi: add DT bindings for UniPhier SPI controller spi: dw: document Microsemi integration spi: img-spfi: Set device select bits for SPFI port state spi: omap2-mcspi: remove several redundant variables spi: dw-mmio: add MSCC Ocelot support spi: dw: export dw_spi_set_cs spi: spi-fsl-espi: Log fifo counters on error spi: imx: Use the longuest possible burst size when in dynamic_burst spi: imx: remove unnecessary check in spi_imx_can_dma spi: imx: Use correct number of bytes per words spi: imx: Use dynamic bursts only when bits_per_word is 8, 16 or 32 ...

Merge tag 'spi-nor/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next

2018-08-11T10:19:35+00:00

Pull SPI NOR updates from Boris Brezillon: " Core changes: - Apply reset hacks only when reset is explicitly marked as broken in the DT Driver changes: - Minor cleanup/fixes in the m25p80 driver - Release flash_np in the nxp-spifi driver - Add suspend/resume hooks to the atmel-quadspi driver - Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver - Use %pK instead of %p in the stm32-quadspi driver - Improve timeout handling in the cadence-quadspi driver - Use mtd_device_register() instead of mtd_device_parse_register() in the intel-spi driver "

Merge tag 'nand/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next

2018-08-11T10:15:19+00:00

Pull NAND updates from Miquel Raynal: " NAND core changes: - Add the SPI-NAND framework. - Create a helper to find the best ECC configuration. - Create NAND controller operations. - Allocate dynamically ONFI parameters structure. - Add defines for ONFI version bits. - Add manufacturer fixup for ONFI parameter page. - Add an option to specify NAND chip as a boot device. - Add Reed-Solomon error correction algorithm. - Better name for the controller structure. - Remove unused caller_is_module() definition. - Make subop helpers return unsigned values. - Expose _notsupp() helpers for raw page accessors. - Add default values for dynamic timings. - Kill the chip->scan_bbt() hook. - Rename nand_default_bbt() into nand_create_bbt(). - Start to clean the nand_chip structure. - Remove stale prototype from rawnand.h. Raw NAND controllers drivers changes: - Qcom: structuring cleanup. - Denali: use core helper to find the best ECC configuration. - Possible build of almost all drivers by adding a dependency on COMPILE_TEST for almost all of them in Kconfig, implies various fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even changes in sparc64 and ia64 architectures. - Clean the ->probe() functions error path of a lot of drivers. - Migrate all drivers to use nand_scan() instead of nand_scan_ident()/nand_scan_tail() pair. - Use mtd_device_register() where applicable to simplify the code. - Marvell: * Handle on-die ECC. * Better clocks handling. * Remove bogus comment. * Add suspend and resume support. - Tegra: add NAND controller driver. - Atmel: * Add module param to avoid using dma. * Drop Wenyou Yang from MAINTAINERS. - Denali: optimize timings handling. - FSMC: Stop using chip->read_buf(). - FSL: * Switch to SPDX license tag identifiers. * Fix qualifiers in MXC init functions. Raw NAND chip drivers changes: - Micron: * Add fixup for ONFI revision. * Update ecc_stats.corrected. * Make ECC activation stateful. * Avoid enabling/disabling ECC when it can't be disabled. * Get the actual number of bitflips. * Allow forced on-die ECC. * Support 8/512 on-die ECC. * Fix on-die ECC detection logic. - Hynix: * Fix decoding the OOB size on H27UCG8T2BTR. * Use ->exec_op() in hynix_nand_reg_write_op(). "

Merge branch 'spi-4.19' into spi-next

2018-08-10T16:51:52+00:00

mtd: m25p80: Call spi_mem_get_name() to let controller set a custom name

2018-08-02T14:35:42+00:00

By calling spi_mem_get_name(), the driver of the (Q)SPI controller can set a custom name for the memory device if necessary. This is useful to keep mtdparts compatible when controller drivers are ported from the MTD to the SPI layer. Suggested-by: Boris Brezillon Signed-off-by: Frieder Schrempf Acked-by: Boris Brezillon Signed-off-by: Mark Brown