kernel/linux.git/drivers/mmc, branch v4.4.171

mmc: omap_hsmmc: fix DMA API warning

2019-01-13T09:05:27+00:00

commit 0b479790684192ab7024ce6a621f93f6d0a64d92 upstream. While booting with rootfs on MMC, the following warning is encountered on OMAP4430: omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536] This is because the DMA engine has a default maximum segment size of 64K but HSMMC sets: mmc->max_blk_size = 512; /* Block Length at max can be 1024 */ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; mmc->max_seg_size = mmc->max_req_size; which ends up telling the block layer that we support a maximum segment size of 65535*512, which exceeds the advertised DMA engine capabilities. Fix this by clamping the maximum segment size to the lower of the maximum request size and of the DMA engine device used for either DMA channel. Signed-off-by: Russell King Cc: Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: core: Reset HPI enabled state during re-init and in case of errors

2019-01-13T09:05:27+00:00

commit a0741ba40a009f97c019ae7541dc61c1fdf41efb upstream. During a re-initialization of the eMMC card, we may fail to re-enable HPI. In these cases, that isn't properly reflected in the card->ext_csd.hpi_en bit, as it keeps being set. This may cause following attempts to use HPI, even if's not enabled. Let's fix this! Fixes: eb0d8f135b67 ("mmc: core: support HPI send command") Cc: Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

MMC: OMAP: fix broken MMC on OMAP15XX/OMAP5910/OMAP310

2018-12-21T13:09:51+00:00

commit e8cde625bfe8a714a856e1366bcbb259d7346095 upstream. Since v2.6.22 or so there has been reports [1] about OMAP MMC being broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON") that changed clock enabling to be done on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX the hardware doesn't seem to like it and the MMC just stops responding. Fix by memorizing the power mode and do the init only when necessary. Before the patch (on Palm TE): mmc0: new SD card at address b368 mmcblk0: mmc0:b368 SDC 977 MiB mmci-omap mmci-omap.0: command timeout (CMD18) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD12) [x 6] mmci-omap mmci-omap.0: command timeout (CMD13) [x 6] mmcblk0: error -110 requesting status mmci-omap mmci-omap.0: command timeout (CMD8) mmci-omap mmci-omap.0: command timeout (CMD18) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD12) [x 6] mmci-omap mmci-omap.0: command timeout (CMD13) [x 6] mmcblk0: error -110 requesting status mmcblk0: recovery failed! print_req_error: I/O error, dev mmcblk0, sector 0 Buffer I/O error on dev mmcblk0, logical block 0, async page read mmcblk0: unable to read partition table After the patch: mmc0: new SD card at address b368 mmcblk0: mmc0:b368 SDC 977 MiB mmcblk0: p1 The patch is based on a fix and analysis done by Ladislav Michl. Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770) and OMAP2420 (Nokia N810). [1] https://marc.info/?t=123175197000003&r=1&w=2 Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON") Reported-by: Ladislav Michl Reported-by: Andrzej Zaborowski Tested-by: Ladislav Michl Acked-by: Tony Lindgren Signed-off-by: Aaro Koskinen Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01

2018-11-21T08:27:31+00:00

[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ] This device reports SDHCI_CLOCK_INT_STABLE even though it's not ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 | SDHCI_CLOCK_CARD_EN but only observed the first operand). mmc1: Timeout waiting for hardware cmd interrupt. mmc1: sdhci: ============ SDHCI REGISTER DUMP =========== mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603 mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001 mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000 mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03 mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083 mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077 mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8 mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000 mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 mmc1: sdhci: Host ctl2: 0x00000008 mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000 mmc1: sdhci: ============================================ The problem happens during wakeup from S3. Adding a delay quirk after power up reliably fixes the problem. Signed-off-by: Yu Zhao Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-iproc: fix 32bit writes for TRANSFER_MODE register

2018-05-30T05:48:51+00:00

commit 5f651b870485ee60f5abbbd85195a6852978894a upstream. When the host controller accepts only 32bit writes, the value of the 16bit TRANSFER_MODE register, that has the same 32bit address as the 16bit COMMAND register, needs to be saved and it will be written in a 32bit write together with the command as this will trigger the host to send the command on the SD interface. When sending the tuning command, TRANSFER_MODE is written and then sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and write it again resulting in wrong value to be written because the initial write value was saved in a shadow and the read-back returned a wrong value, from the register. Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE when a saved value exist. Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are saved for a different reason, although a scenario that will cause the mentioned problem on this registers is not probable. Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver") Signed-off-by: Corneliu Doban Signed-off-by: Scott Branden Cc: stable@vger.kernel.org # v4.1+ Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: jz4740: Fix race condition in IRQ mask update

2018-04-24T07:32:08+00:00

commit a04f0017c22453613d5f423326b190c61e3b4f98 upstream. A spinlock is held while updating the internal copy of the IRQ mask, but not while writing it to the actual IMASK register. After the lock is released, an IRQ can occur before the IMASK register is written. If handling this IRQ causes the mask to be changed, when the handler returns back to the middle of the first mask update, a stale value will be written to the mask register. If this causes an IRQ to become unmasked that cannot have its status cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ, then we can end up stuck with the same IRQ repeatedly being fired but not handled. Normally the MMC IRQ handler attempts to clear any unexpected IRQs by writing IREG, but for those that cannot be cleared in this way then the IRQ will just repeatedly fire. This was resulting in lockups after a while of using Wi-Fi on the CI20 (GitHub issue #19). Resolve by holding the spinlock until after the IMASK register has been updated. Cc: stable@vger.kernel.org Link: https://github.com/MIPS/CI20_linux/issues/19 Fixes: 61bfbdb85687 ("MMC: Add support for the controller on JZ4740 SoCs.") Tested-by: Mathieu Malaterre Signed-off-by: Alex Smith Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occurs

2018-03-28T16:40:13+00:00

commit 47b7de2f6c18f75d1f2716efe752cba43f32a626 upstream. It was found that in IDMAC mode after soft-reset driver switches to PIO mode. That's what happens in case of DTO timeout overflow calculation failure: 1. soft-reset is called 2. driver restarts dma 3. descriptors states are checked, one of descriptor is owned by the IDMAC. 4. driver can't use DMA and then switches to PIO mode. Failure was already fixed in: https://www.spinics.net/lists/linux-mmc/msg48125.html. Behaviour while soft-reset is not something we except or even want to happen. So we switch from dw_mci_idmac_reset to dw_mci_idmac_init, so descriptors are cleaned before starting dma. And while at it explicitly zero des0 which otherwise might contain garbage as being allocated by dmam_alloc_coherent(). Signed-off-by: Evgeniy Didin Cc: Jaehoon Chung Cc: Ulf Hansson Cc: Andy Shevchenko Cc: Jisheng Zhang Cc: Shawn Lin Cc: Alexey Brodkin Cc: Eugeniy Paltsev Cc: linux-snps-arc@lists.infradead.org Cc: # 4.4+ Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: avoid removing non-removable hosts during suspend

2018-03-24T09:58:47+00:00

[ Upstream commit de8dcc3d2c0e08e5068ee1e26fc46415c15e3637 ] The Weibu F3C MiniPC has an onboard AP6255 module, presenting two SDIO functions on a single MMC host (Bluetooth/btsdio and WiFi/brcmfmac), and the mmc layer correctly detects this as non-removable. After suspend/resume, the wifi and bluetooth interfaces disappear and do not get probed again. The conditions here are: 1. During suspend, we reach mmc_pm_notify() 2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can suspend the SDIO host. However, mmc_sdio_pre_suspend() returns -ENOSYS because btsdio_driver does not have a suspend method. 3. mmc_pm_notify() proceeds to remove the card 4. Upon resume, mmc_rescan() does nothing with this host, because of the rescan_entered check which aims to only scan a non-removable device a single time (i.e. during boot). Fix the loss of functionality by detecting that we are unable to suspend a non-removable host, so avoid the forced removal in that case. The comment above this function already indicates that this code was only intended for removable devices. Signed-off-by: Daniel Drake Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a

2018-03-24T09:58:45+00:00

[ Upstream commit a627f025eb0534052ff451427c16750b3530634c ] The ls1046a datasheet specified that the max SD clock frequency for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet specified it's 125MHz for ls1012a. So this patch is to add the limitation. Signed-off-by: Yangbo Lu Acked-by: Adrian Hunter Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

mmc: host: omap_hsmmc: checking for NULL instead of IS_ERR()

2018-03-24T09:58:43+00:00

[ Upstream commit ec5ab8933772c87f24ad62a4a602fe8949f423c2 ] devm_pinctrl_get() returns error pointers, it never returns NULL. Fixes: 455e5cd6f736 ("mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x") Signed-off-by: Dan Carpenter Reviewed-by: Kishon Vijay Abraham I Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman