kernel/linux.git/drivers/mmc, branch v4.19.77

mmc: dw_mmc: Re-store SDIO IRQs mask at system resume

2019-10-05T11:09:57+00:00

[ Upstream commit 7c526608d5afb62cbc967225e2ccaacfdd142e9d ] In cases when SDIO IRQs have been enabled, runtime suspend is prevented by the driver. However, this still means dw_mci_runtime_suspend|resume() gets called during system suspend/resume, via pm_runtime_force_suspend|resume(). This means during system suspend/resume, the register context of the dw_mmc device most likely loses its register context, even in cases when SDIO IRQs have been enabled. To re-enable the SDIO IRQs during system resume, the dw_mmc driver currently relies on the mmc core to re-enable the SDIO IRQs when it resumes the SDIO card, but this isn't the recommended solution. Instead, it's better to deal with this locally in the dw_mmc driver, so let's do that. Tested-by: Matthias Kaehlcke Signed-off-by: Ulf Hansson Reviewed-by: Douglas Anderson Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: sdhci: Fix incorrect switch to HS mode

2019-10-05T11:09:56+00:00

[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ] When switching from any MMC speed mode that requires 1.8v (HS200, HS400 and HS400ES) to High Speed (HS) mode, the system ends up configured for SDR12 with a 50MHz clock which is an illegal mode. This happens because the SDHCI_CTRL_VDD_180 bit in the SDHCI_HOST_CONTROL2 register is left set and when this bit is set, the speed mode is controlled by the SDHCI_CTRL_UHS field in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling() because there is no UHS mode being set. The fix is to change sdhci_set_uhs_signaling() to set the SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for any switch to HS mode. This was found on a new eMMC controller that does strict checking of the speed mode and the corresponding clock rate. It caused the switch to HS400 mode to fail because part of the sequence to switch to HS400 requires a switch from HS200 to HS before going to HS400. Suggested-by: Adrian Hunter Signed-off-by: Al Cooper Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: core: Clarify sdio_irq_pending flag for MMC_CAP2_SDIO_IRQ_NOTHREAD

2019-10-05T11:09:56+00:00

[ Upstream commit 36d57efb4af534dd6b442ea0b9a04aa6dfa37abe ] The sdio_irq_pending flag is used to let host drivers indicate that it has signaled an IRQ. If that is the case and we only have a single SDIO func that have claimed an SDIO IRQ, our assumption is that we can avoid reading the SDIO_CCCR_INTx register and just call the SDIO func irq handler immediately. This makes sense, but the flag is set/cleared in a somewhat messy order, let's fix that up according to below. First, the flag is currently set in sdio_run_irqs(), which is executed as a work that was scheduled from sdio_signal_irq(). To make it more implicit that the host have signaled an IRQ, let's instead immediately set the flag in sdio_signal_irq(). This also makes the behavior consistent with host drivers that uses the legacy, mmc_signal_sdio_irq() API. This have no functional impact, because we don't expect host drivers to call sdio_signal_irq() until after the work (sdio_run_irqs()) have been executed anyways. Second, currently we never clears the flag when using the sdio_run_irqs() work, but only when using the sdio_irq_thread(). Let make the behavior consistent, by moving the flag to be cleared inside the common process_sdio_pending_irqs() function. Additionally, tweak the behavior of the flag slightly, by avoiding to clear it unless we processed the SDIO IRQ. The purpose with this at this point, is to keep the information about whether there have been an SDIO IRQ signaled by the host, so at system resume we can decide to process it without reading the SDIO_CCCR_INTx register. Tested-by: Matthias Kaehlcke Reviewed-by: Matthias Kaehlcke Signed-off-by: Ulf Hansson Reviewed-by: Douglas Anderson Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: sdhci-pci: Add support for Intel CML

2019-09-16T06:22:13+00:00

[ Upstream commit 765c59675ab571caf7ada456bbfd23a73136b535 ] Add PCI Ids for Intel CML. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: renesas_sdhi: Fix card initialization failure in high speed mode

2019-09-16T06:22:07+00:00

[ Upstream commit d30ae056adb81e1d2b8b953efa74735a020b8e3b ] This fixes card initialization failure in high speed mode. If U-Boot uses SDR or HS200/400 mode before starting Linux and Linux DT does not enable SDR/HS200/HS400 mode, card initialization fails in high speed mode. It is necessary to initialize SCC registers during card initialization phase. HW reset function is registered only for a port with either of SDR/HS200/HS400 properties in device tree. If SDR/HS200/HS400 properties are not present in device tree, SCC registers will not be reset. In SoC that support SCC registers, HW reset function should be registered regardless of the configuration of device tree. Reproduction procedure: - Use U-Boot that support MMC HS200/400 mode. - Delete HS200/HS400 properties in device tree. (Delete mmc-hs200-1_8v and mmc-hs400-1_8v) - MMC port works high speed mode and all commands fail. Signed-off-by: Takeshi Saito Signed-off-by: Marek Vasut Cc: Niklas Söderlund Cc: Simon Horman Reviewed-by: Wolfram Sang Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: core: Fix init of SD cards reporting an invalid VDD range

2019-09-06T08:22:17+00:00

commit 72741084d903e65e121c27bd29494d941729d4a1 upstream. The OCR register defines the supported range of VDD voltages for SD cards. However, it has turned out that some SD cards reports an invalid voltage range, for example having bit7 set. When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from the invalid VDD range, this triggers the core to run a power cycle of the card to try to initialize it at the lowest common supported voltage. Obviously this fails, since the card can't support it. Let's fix this problem, by clearing invalid bits from the read OCR register for SD cards, before proceeding with the VDD voltage negotiation. Cc: stable@vger.kernel.org Reported-by: Philip Langdale Signed-off-by: Ulf Hansson Reviewed-by: Philip Langdale Tested-by: Philip Langdale Tested-by: Manuel Presnitz Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-at91: add quirk for broken HS200

2019-09-06T08:22:17+00:00

commit 7871aa60ae0086fe4626abdf5ed13eeddf306c61 upstream. HS200 is not implemented in the driver, but the controller claims it through caps. Remove it via a quirk, to make sure the mmc core do not try to enable HS200, as it causes the eMMC initialization to fail. Signed-off-by: Eugen Hristev Acked-by: Ludovic Desroches Acked-by: Adrian Hunter Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-arasan: Do now show error message in case of deffered probe

2019-08-25T08:48:05+00:00

commit 60208a267208c27fa3f23dfd36cbda180471fa98 upstream. When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return -EPROBE_DEFER because driver for power sequence provider is not probed yet. Do not show error message when this situation happens. Signed-off-by: Michal Simek Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: cavium: Add the missing dma unmap when the dma has finished.

2019-08-16T08:12:39+00:00

commit b803974a86039913d5280add083d730b2b9ed8ec upstream. This fixes the below calltrace when the CONFIG_DMA_API_DEBUG is enabled. DMA-API: thunderx_mmc 0000:01:01.4: cpu touching an active dma mapped cacheline [cln=0x000000002fdf9800] WARNING: CPU: 21 PID: 1 at kernel/dma/debug.c:596 debug_dma_assert_idle+0x1f8/0x270 Modules linked in: CPU: 21 PID: 1 Comm: init Not tainted 5.3.0-rc1-next-20190725-yocto-standard+ #64 Hardware name: Marvell OcteonTX CN96XX board (DT) pstate: 80400009 (Nzcv daif +PAN -UAO) pc : debug_dma_assert_idle+0x1f8/0x270 lr : debug_dma_assert_idle+0x1f8/0x270 sp : ffff0000113cfc10 x29: ffff0000113cfc10 x28: 0000ffff8c880000 x27: ffff800bc72a0000 x26: ffff000010ff8000 x25: ffff000010ff8940 x24: ffff000010ff8968 x23: 0000000000000000 x22: ffff000010e83700 x21: ffff000010ea2000 x20: ffff000010e835c8 x19: ffff800bc2c73300 x18: ffffffffffffffff x17: 0000000000000000 x16: 0000000000000000 x15: ffff000010e835c8 x14: 6d20616d64206576 x13: 69746361206e6120 x12: 676e696863756f74 x11: 20757063203a342e x10: 31303a31303a3030 x9 : 303020636d6d5f78 x8 : 3230303030303030 x7 : 00000000000002fd x6 : ffff000010fd57d0 x5 : 0000000000000000 x4 : ffff0000106c5210 x3 : 00000000ffffffff x2 : 0000800bee9c0000 x1 : 57d5843f4aa62800 x0 : 0000000000000000 Call trace: debug_dma_assert_idle+0x1f8/0x270 wp_page_copy+0xb0/0x688 do_wp_page+0xa8/0x5b8 __handle_mm_fault+0x600/0xd00 handle_mm_fault+0x118/0x1e8 do_page_fault+0x200/0x500 do_mem_abort+0x50/0xb0 el0_da+0x20/0x24 ---[ end trace a005534bd23e109f ]--- DMA-API: Mapped at: debug_dma_map_sg+0x94/0x350 cvm_mmc_request+0x3c4/0x988 __mmc_start_request+0x9c/0x1f8 mmc_start_request+0x7c/0xb0 mmc_blk_mq_issue_rq+0x5c4/0x7b8 Signed-off-by: Kevin Hao Fixes: ba3869ff32e4 ("mmc: cavium: Add core MMC driver for Cavium SOCs") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: cavium: Set the correct dma max segment size for mmc_host

2019-08-16T08:12:39+00:00

commit fa25eba6993b3750f417baabba169afaba076178 upstream. We have set the mmc_host.max_seg_size to 8M, but the dma max segment size of PCI device is set to 64K by default in function pci_device_add(). The mmc_host.max_seg_size is used to set the max segment size of the blk queue. Then this mismatch will trigger a calltrace like below when a bigger than 64K segment request arrives at mmc dev. So we should consider the limitation of the cvm_mmc_host when setting the mmc_host.max_seg_size. DMA-API: thunderx_mmc 0000:01:01.4: mapping sg segment longer than device claims to support [len=131072] [max=65536] WARNING: CPU: 6 PID: 238 at kernel/dma/debug.c:1221 debug_dma_map_sg+0x2b8/0x350 Modules linked in: CPU: 6 PID: 238 Comm: kworker/6:1H Not tainted 5.3.0-rc1-next-20190724-yocto-standard+ #62 Hardware name: Marvell OcteonTX CN96XX board (DT) Workqueue: kblockd blk_mq_run_work_fn pstate: 80c00009 (Nzcv daif +PAN +UAO) pc : debug_dma_map_sg+0x2b8/0x350 lr : debug_dma_map_sg+0x2b8/0x350 sp : ffff00001770f9e0 x29: ffff00001770f9e0 x28: ffffffff00000000 x27: 00000000ffffffff x26: ffff800bc2c73180 x25: ffff000010e83700 x24: 0000000000000002 x23: 0000000000000001 x22: 0000000000000001 x21: 0000000000000000 x20: ffff800bc48ba0b0 x19: ffff800bc97e8c00 x18: ffffffffffffffff x17: 0000000000000000 x16: 0000000000000000 x15: ffff000010e835c8 x14: 6874207265676e6f x13: 6c20746e656d6765 x12: 7320677320676e69 x11: 7070616d203a342e x10: 31303a31303a3030 x9 : 303020636d6d5f78 x8 : 35363d78616d5b20 x7 : 00000000000002fd x6 : ffff000010fd57dc x5 : 0000000000000000 x4 : ffff0000106c61f0 x3 : 00000000ffffffff x2 : 0000800bee060000 x1 : 7010678df3041a00 x0 : 0000000000000000 Call trace: debug_dma_map_sg+0x2b8/0x350 cvm_mmc_request+0x3c4/0x988 __mmc_start_request+0x9c/0x1f8 mmc_start_request+0x7c/0xb0 mmc_blk_mq_issue_rq+0x5c4/0x7b8 mmc_mq_queue_rq+0x11c/0x278 blk_mq_dispatch_rq_list+0xb0/0x568 blk_mq_do_dispatch_sched+0x6c/0x108 blk_mq_sched_dispatch_requests+0x110/0x1b8 __blk_mq_run_hw_queue+0xb0/0x118 blk_mq_run_work_fn+0x28/0x38 process_one_work+0x210/0x490 worker_thread+0x48/0x458 kthread+0x130/0x138 ret_from_fork+0x10/0x1c Signed-off-by: Kevin Hao Fixes: ba3869ff32e4 ("mmc: cavium: Add core MMC driver for Cavium SOCs") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman