kernel/linux.git/drivers/mmc/host, branch v6.1.175

mmc: sdhci-of-dwcmshc: Disable clock before DLL configuration

2026-06-01T15:38:48+00:00

commit 6546a49bbe656981d99a389195560999058c89c4 upstream. According to the ASIC design recommendations, the clock must be disabled before operating the DLL to prevent glitches that could affect the internal digital logic. In extreme cases, failing to do so may cause the controller to malfunction completely. Adds a step to disable the clock before DLL configuration and re-enables it at the end. Fixes: 08f3dff799d4 ("mmc: sdhci-of-dwcmshc: add rockchip platform support") Cc: stable@vger.kernel.org Signed-off-by: Shawn Lin Acked-by: Adrian Hunter Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: vub300: fix NULL-deref on disconnect

2026-04-18T08:35:58+00:00

commit dff34ef879c5e73298443956a8b391311ba78d57 upstream. Make sure to deregister the controller before dropping the reference to the driver data on disconnect to avoid NULL-pointer dereferences or use-after-free. Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver") Cc: stable@vger.kernel.org # 3.0+ Signed-off-by: Johan Hovold Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: fix timing selection for 1-bit bus width

2026-03-25T10:03:12+00:00

commit 5e3486e64094c28a526543f1e8aa0d5964b7f02d upstream. When 1-bit bus width is used with HS200/HS400 capabilities set, mmc_select_hs200() returns 0 without actually switching. This causes mmc_select_timing() to skip mmc_select_hs(), leaving eMMC in legacy mode (26MHz) instead of High Speed SDR (52MHz). Per JEDEC eMMC spec section 5.3.2, 1-bit mode supports High Speed SDR. Drop incompatible HS200/HS400/UHS/DDR caps early so timing selection falls through to mmc_select_hs() correctly. Fixes: f2119df6b764 ("mmc: sd: add support for signal voltage switch procedure") Signed-off-by: Luke Wang Acked-by: Adrian Hunter Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-pci-gli: fix GL9750 DMA write corruption

2026-03-25T10:03:12+00:00

commit 2b76e0cc7803e5ab561c875edaba7f6bbd87fbb0 upstream. The GL9750 SD host controller has intermittent data corruption during DMA write operations. The GM_BURST register's R_OSRC_Lmt field (bits 17:16), which limits outstanding DMA read requests from system memory, is not being cleared during initialization. The Windows driver sets R_OSRC_Lmt to zero, limiting requests to the smallest unit. Clear R_OSRC_Lmt to match the Windows driver behavior. This eliminates write corruption verified with f3write/f3read tests while maintaining DMA performance. Cc: stable@vger.kernel.org Fixes: e51df6ce668a ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support") Closes: https://lore.kernel.org/linux-mmc/33d12807-5c72-41ce-8679-57aa11831fad@linux.dev/ Acked-by: Adrian Hunter Signed-off-by: Matthew Schwartz Reviewed-by: Ben Chuang Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: mmci: Fix device_node reference leak in of_get_dml_pipe_index()

2026-03-25T10:03:07+00:00

commit af12e64ae0661546e8b4f5d30d55c5f53a11efe7 upstream. When calling of_parse_phandle_with_args(), the caller is responsible to call of_node_put() to release the reference of device node. In of_get_dml_pipe_index(), it does not release the reference. Fixes: 9cb15142d0e3 ("mmc: mmci: Add qcom dml support to the driver.") Signed-off-by: Felix Gu Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

Revert "mmc: rtsx_pci_sdmmc: increase power-on settling delay to 5ms"

2026-03-04T12:19:59+00:00

[ Upstream commit ff112f1ecd10b72004eac05bae395e1c65f0c63c ] This reverts commit aced969e9bf3701dc75cfca57c78c031b7875b9d. It was determined that this was not the correct "fix", so should be reverted. Fixes: aced969e9bf3 ("mmc: rtsx_pci_sdmmc: increase power-on settling delay to 5ms") Cc: Matthew Schwartz Cc: Ulf Hansson Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

mmc: rtsx_pci_sdmmc: increase power-on settling delay to 5ms

2026-03-04T12:19:58+00:00

[ Upstream commit aced969e9bf3701dc75cfca57c78c031b7875b9d ] The existing 1ms delay in sd_power_on is insufficient and causes resume errors around 4% of the time. Increasing the delay to 5ms resolves this issue after testing 300 s2idle cycles. Fixes: 1f311c94aabd ("mmc: rtsx: add 74 Clocks in power on flow") Signed-off-by: Matthew Schwartz Link: https://patch.msgid.link/20260105060236.400366-3-matthew.schwartz@linux.dev Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

mmc: sdhci-of-dwcmshc: Prevent illegal clock reduction in HS200/HS400 mode

2026-02-06T15:44:20+00:00

[ Upstream commit 3009738a855cf938bbfc9078bec725031ae623a4 ] When operating in HS200 or HS400 timing modes, reducing the clock frequency below 52MHz will lead to link broken as the Rockchip DWC MSHC controller requires maintaining a minimum clock of 52MHz in these modes. Add a check to prevent illegal clock reduction through debugfs: root@debian:/# echo 50000000 > /sys/kernel/debug/mmc0/clock root@debian:/# [ 30.090146] mmc0: running CQE recovery mmc0: cqhci: Failed to halt mmc0: cqhci: spurious TCN for tag 0 WARNING: drivers/mmc/host/cqhci-core.c:797 at cqhci_irq+0x254/0x818, CPU#1: kworker/1:0H/24 Modules linked in: CPU: 1 UID: 0 PID: 24 Comm: kworker/1:0H Not tainted 6.19.0-rc1-00001-g09db0998649d-dirty #204 PREEMPT Hardware name: Rockchip RK3588 EVB1 V10 Board (DT) Workqueue: kblockd blk_mq_run_work_fn pstate: 604000c9 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : cqhci_irq+0x254/0x818 lr : cqhci_irq+0x254/0x818 ... Fixes: c6f361cba51c ("mmc: sdhci-of-dwcmshc: add support for rk3588") Cc: Sebastian Reichel Cc: Yifeng Zhao Signed-off-by: Shawn Lin Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-dwcmshc: Update DLL and pre-change delay for rockchip platform

2026-02-06T15:44:20+00:00

[ Upstream commit b75a52b0dda353aeefb4830a320589a363f49579 ] For Rockchip platform, DLL bypass bit and start bit need to be set if DLL is not locked. And adjust pre-change delay to 0x3 for better signal test result. Signed-off-by: Shawn Lin Link: https://lore.kernel.org/r/1675298118-64243-2-git-send-email-shawn.lin@rock-chips.com Signed-off-by: Ulf Hansson Stable-dep-of: 3009738a855c ("mmc: sdhci-of-dwcmshc: Prevent illegal clock reduction in HS200/HS400 mode") Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

mmc: rtsx_pci_sdmmc: implement sdmmc_card_busy function

2026-02-06T15:44:11+00:00

commit 122610220134b32c742cc056eaf64f7017ac8cd9 upstream. rtsx_pci_sdmmc does not have an sdmmc_card_busy function, so any voltage switches cause a kernel warning, "mmc0: cannot verify signal voltage switch." Copy the sdmmc_card_busy function from rtsx_pci_usb to rtsx_pci_sdmmc to fix this. Fixes: ff984e57d36e ("mmc: Add realtek pcie sdmmc host driver") Signed-off-by: Matthew Schwartz Tested-by: Ricky WU Reviewed-by: Ricky WU Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman