kernel/linux.git/drivers/mmc/host, branch v4.14.286

mmc: rtsx: add 74 Clocks in power on flow

2022-05-15T17:40:26+00:00

commit 1f311c94aabdb419c28e3147bcc8ab89269f1a7e upstream. SD spec definition: "Host provides at least 74 Clocks before issuing first command" After 1ms for the voltage stable then start issuing the Clock signals if POWER STATE is MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card Signed-off-by: Ricky Wu Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com Signed-off-by: Ulf Hansson Signed-off-by: Ricky Wu Signed-off-by: Ulf Hansson Signed-off-by: Christian Loehle Signed-off-by: Greg Kroah-Hartman

Revert "mmc: sdhci-xenon: fix annoying 1.8V regulator warning"

2022-04-20T07:08:29+00:00

commit 7e2646ed47542123168d43916b84b954532e5386 upstream. This reverts commit bb32e1987bc55ce1db400faf47d85891da3c9b9f. Commit 1a3ed0dc3594 ("mmc: sdhci-xenon: fix 1.8v regulator stabilization") contains proper fix for the issue described in commit bb32e1987bc5 ("mmc: sdhci-xenon: fix annoying 1.8V regulator warning"). Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V signal enable") Cc: stable@vger.kernel.org # 1a3ed0dc3594 ("mmc: sdhci-xenon: fix 1.8v regulator stabilization") Signed-off-by: Pali Rohár Reviewed-by: Marek Behún Reviewed-by: Marcin Wojtas Link: https://lore.kernel.org/r/20220318141441.32329-1-pali@kernel.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-esdhc: Check for error num after setting mask

2022-02-16T11:44:49+00:00

commit 40c67c291a93f8846c4a972c9ef1b7ba4544c8d0 upstream. Because of the possible failure of the dma_supported(), the dma_set_mask_and_coherent() may return error num. Therefore, it should be better to check it and return the error if fails. And since the sdhci_setup_host() has already checked the return value of the enable_dma, we need not check it in sdhci_resume_host() again. Fixes: 5552d7ad596c ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips") Signed-off-by: Jiasheng Jiang Acked-by: Adrian Hunter Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220112083156.1124782-1-jiasheng@iscas.ac.cn Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

moxart: fix potential use-after-free on remove path

2022-02-11T07:43:36+00:00

commit bd2db32e7c3e35bd4d9b8bbff689434a50893546 upstream. It was reported that the mmc host structure could be accessed after it was freed in moxart_remove(), so fix this by saving the base register of the device and using it instead of the pointer dereference. Cc: Ulf Hansson Cc: Xiyu Yang Cc: Xin Xiong Cc: Xin Tan Cc: Tony Lindgren Cc: Yang Li Cc: linux-mmc@vger.kernel.org Cc: stable Reported-by: whitehat002 Signed-off-by: Greg Kroah-Hartman Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: mxs-mmc: disable regulator on error and in the remove function

2021-11-26T10:40:31+00:00

[ Upstream commit ce5f6c2c9b0fcb4094f8e162cfd37fb4294204f7 ] The 'reg_vmmc' regulator is enabled in the probe. It is never disabled. Neither in the error handling path of the probe nor in the remove function. Register a devm_action to disable it when needed. Fixes: 4dc5a79f1350 ("mmc: mxs-mmc: enable regulator for mmc slot") Signed-off-by: Christophe JAILLET Link: https://lore.kernel.org/r/4aadb3c97835f7b80f00819c3d549e6130384e67.1634365151.git.christophe.jaillet@wanadoo.fr Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: winbond: don't build on M68K

2021-11-26T10:40:22+00:00

[ Upstream commit 162079f2dccd02cb4b6654defd32ca387dd6d4d4 ] The Winbond MMC driver fails to build on ARCH=m68k so prevent that build config. Silences these build errors: ../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end': ../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration] 212 | dmaflags = claim_dma_lock(); ../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration] 215 | release_dma_lock(dmaflags); Signed-off-by: Randy Dunlap Cc: Pierre Ossman Cc: Geert Uytterhoeven Cc: Arnd Bergmann Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: dw_mmc: Dont wait for DRTO on Write RSP error

2021-11-26T10:40:20+00:00

commit 43592c8736e84025d7a45e61a46c3fa40536a364 upstream. Only wait for DRTO on reads, otherwise the driver hangs. The driver prevents sending CMD12 on response errors like CRCs. According to the comment this is because some cards have problems with this during the UHS tuning sequence. Unfortunately this workaround currently also applies for any command with data. On reads this will set the drto timer, which then triggers after a while. On writes this will not set any timer and the tasklet will not be scheduled again. I cannot test for the UHS workarounds need, but even if so, it should at most apply to reads. I have observed many hangs when CMD25 response contained a CRC error. This patch fixes this without touching the actual UHS tuning workaround. Signed-off-by: Christian Loehle Reviewed-by: Jaehoon Chung Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-esdhc-imx: clear the buffer_read_ready to reset standard tuning circuit

2021-11-02T17:25:12+00:00

commit 9af372dc70e9fdcbb70939dac75365e7b88580b4 upstream. To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE, also need to clear bit buffer_read_ready, this operation will finally clear the USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following normal data transfer will not be impacted by standard tuning logic used before. Find this issue when do quick SD card insert/remove stress test. During standard tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all data related commands can't get any data related interrupts, include data transfer complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt. Always trigger software timeout issue. Even reset the USDHC through bits in register SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24 reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't be recognized any more. Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card") Signed-off-by: Haibo Chen Acked-by: Adrian Hunter Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci: Map more voltage level to SDHCI_POWER_330

2021-11-02T17:25:12+00:00

commit 4217d07b9fb328751f877d3bd9550122014860a2 upstream. On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V), which is being treated as an invalid value by sdhci_set_power_noreg(). And thus eMMC is totally broken on the platform. [ 1.436599] ------------[ cut here ]------------ [ 1.436606] mmc0: Invalid vdd 0x17 [ 1.436640] WARNING: CPU: 2 PID: 69 at drivers/mmc/host/sdhci.c:2048 sdhci_set_power_noreg+0x168/0x2b4 [ 1.436655] Modules linked in: [ 1.436662] CPU: 2 PID: 69 Comm: kworker/u8:1 Tainted: G W 5.15.0-rc1+ #137 [ 1.436669] Hardware name: Thundercomm TurboX CM2290 (DT) [ 1.436674] Workqueue: events_unbound async_run_entry_fn [ 1.436685] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1.436692] pc : sdhci_set_power_noreg+0x168/0x2b4 [ 1.436698] lr : sdhci_set_power_noreg+0x168/0x2b4 [ 1.436703] sp : ffff800010803a60 [ 1.436705] x29: ffff800010803a60 x28: ffff6a9102465f00 x27: ffff6a9101720a70 [ 1.436715] x26: ffff6a91014de1c0 x25: ffff6a91014de010 x24: ffff6a91016af280 [ 1.436724] x23: ffffaf7b1b276640 x22: 0000000000000000 x21: ffff6a9101720000 [ 1.436733] x20: ffff6a9101720370 x19: ffff6a9101720580 x18: 0000000000000020 [ 1.436743] x17: 0000000000000000 x16: 0000000000000004 x15: ffffffffffffffff [ 1.436751] x14: 0000000000000000 x13: 00000000fffffffd x12: ffffaf7b1b84b0bc [ 1.436760] x11: ffffaf7b1b720d10 x10: 000000000000000a x9 : ffff800010803a60 [ 1.436769] x8 : 000000000000000a x7 : 000000000000000f x6 : 00000000fffff159 [ 1.436778] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000ffffffff [ 1.436787] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff6a9101718d80 [ 1.436797] Call trace: [ 1.436800] sdhci_set_power_noreg+0x168/0x2b4 [ 1.436805] sdhci_set_ios+0xa0/0x7fc [ 1.436811] mmc_power_up.part.0+0xc4/0x164 [ 1.436818] mmc_start_host+0xa0/0xb0 [ 1.436824] mmc_add_host+0x60/0x90 [ 1.436830] __sdhci_add_host+0x174/0x330 [ 1.436836] sdhci_msm_probe+0x7c0/0x920 [ 1.436842] platform_probe+0x68/0xe0 [ 1.436850] really_probe.part.0+0x9c/0x31c [ 1.436857] __driver_probe_device+0x98/0x144 [ 1.436863] driver_probe_device+0xc8/0x15c [ 1.436869] __device_attach_driver+0xb4/0x120 [ 1.436875] bus_for_each_drv+0x78/0xd0 [ 1.436881] __device_attach_async_helper+0xac/0xd0 [ 1.436888] async_run_entry_fn+0x34/0x110 [ 1.436895] process_one_work+0x1d0/0x354 [ 1.436903] worker_thread+0x13c/0x470 [ 1.436910] kthread+0x150/0x160 [ 1.436915] ret_from_fork+0x10/0x20 [ 1.436923] ---[ end trace fcfac44cb045c3a8 ]--- Fix the issue by mapping MMC_VDD_35_36 (and MMC_VDD_34_35) to SDHCI_POWER_330 as well. Signed-off-by: Shawn Guo Acked-by: Adrian Hunter Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211004024935.15326-1-shawn.guo@linaro.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: dw_mmc: exynos: fix the finding clock sample value

2021-11-02T17:25:12+00:00

commit 697542bceae51f7620af333b065dd09d213629fb upstream. Even though there are candiates value if can't find best value, it's returned -EIO. It's not proper behavior. If there is not best value, use a first candiate value to work eMMC. Signed-off-by: Jaehoon Chung Tested-by: Marek Szyprowski Tested-by: Christian Hewitt Cc: stable@vger.kernel.org Fixes: c537a1c5ff63 ("mmc: dw_mmc: exynos: add variable delay tuning sequence") Link: https://lore.kernel.org/r/20211022082106.1557-1-jh80.chung@samsung.com Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman