kernel/linux.git/drivers/mmc/host, branch v4.14.217

mmc: via-sdmmc: Fix data race bug

2020-11-05T10:06:55+00:00

[ Upstream commit 87d7ad089b318b4f319bf57f1daa64eb6d1d10ad ] via_save_pcictrlreg() should be called with host->lock held as it writes to pm_pcictrl_reg, otherwise there can be a race condition between via_sd_suspend() and via_sdc_card_detect(). The same pattern is used in the function via_reset_pcictrl() as well, where via_save_pcictrlreg() is called with host->lock held. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Madhuparna Bhowmik Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: sdhci-msm: Add retries when all tuning phases are found valid

2020-09-23T08:46:26+00:00

[ Upstream commit 9d5dcefb7b114d610aeb2371f6a6f119af316e43 ] As the comments in this patch say, if we tune and find all phases are valid it's _almost_ as bad as no phases being found valid. Probably all phases are not really reliable but we didn't detect where the unreliable place is. That means we'll essentially be guessing and hoping we get a good phase. This is not just a problem in theory. It was causing real problems on a real board. On that board, most often phase 10 is found as the only invalid phase, though sometimes 10 and 11 are invalid and sometimes just 11. Some percentage of the time, however, all phases are found to be valid. When this happens, the current logic will decide to use phase 11. Since phase 11 is sometimes found to be invalid, this is a bad choice. Sure enough, when phase 11 is picked we often get mmc errors later in boot. I have seen cases where all phases were found to be valid 3 times in a row, so increase the retry count to 10 just to be extra sure. Fixes: 415b5a75da43 ("mmc: sdhci-msm: Add platform_execute_tuning implementation") Signed-off-by: Douglas Anderson Reviewed-by: Veerabhadrarao Badiganti Acked-by: Adrian Hunter Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeid Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: sdhci: do not enable card detect interrupt for gpio cd type

2020-07-22T07:22:23+00:00

[ Upstream commit e65bb38824711559844ba932132f417bc5a355e2 ] Except SDHCI_QUIRK_BROKEN_CARD_DETECTION and MMC_CAP_NONREMOVABLE, we also do not need to handle controller native card detect interrupt for gpio cd type. If we wrong enabled the card detect interrupt for gpio case, it will cause a lot of unexpected card detect interrupts during data transfer which should not happen. Signed-off-by: Haibo Chen Acked-by: Adrian Hunter Reviewed-by: Linus Walleij Link: https://lore.kernel.org/r/1582100563-20555-2-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: sdhci-esdhc-imx: fix the mask for tuning start point

2020-06-20T08:25:14+00:00

[ Upstream commit 1194be8c949b8190b2882ad8335a5d98aa50c735 ] According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is TUNING_START_TAP, bit[7] of this register is to disable the command CRC check for standard tuning. So fix it here. Fixes: d87fc9663688 ("mmc: sdhci-esdhc-imx: support setting tuning start point") Signed-off-by: Haibo Chen Link: https://lore.kernel.org/r/1590488522-9292-1-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: via-sdmmc: Respect the cmd->busy_timeout from the mmc core

2020-06-20T08:25:14+00:00

[ Upstream commit 966244ccd2919e28f25555a77f204cd1c109cad8 ] Using a fixed 1s timeout for all commands (and data transfers) is a bit problematic. For some commands it means waiting longer than needed for the timer to expire, which may not a big issue, but still. For other commands, like for an erase (CMD38) that uses a R1B response, may require longer timeouts than 1s. In these cases, we may end up treating the command as it failed, while it just needed some more time to complete successfully. Fix the problem by respecting the cmd->busy_timeout, which is provided by the mmc core. Cc: Bruce Chang Cc: Harald Welte Signed-off-by: Ulf Hansson Link: https://lore.kernel.org/r/20200414161413.3036-17-ulf.hansson@linaro.org Signed-off-by: Sasha Levin

mmc: sdhci-msm: Set SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirk

2020-06-20T08:25:14+00:00

[ Upstream commit d863cb03fb2aac07f017b2a1d923cdbc35021280 ] sdhci-msm can support auto cmd12. So enable SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirk. Signed-off-by: Veerabhadrarao Badiganti Acked-by: Adrian Hunter Link: https://lore.kernel.org/r/1587363626-20413-3-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson Signed-off-by: Sasha Levin

mmc: sdhci-msm: Clear tuning done flag while hs400 tuning

2020-06-20T08:25:06+00:00

commit 9253d71011c349d5f5cc0cebdf68b4a80811b92d upstream. Clear tuning_done flag while executing tuning to ensure vendor specific HS400 settings are applied properly when the controller is re-initialized in HS400 mode. Without this, re-initialization of the qcom SDHC in HS400 mode fails while resuming the driver from runtime-suspend or system-suspend. Fixes: ff06ce417828 ("mmc: sdhci-msm: Add HS400 platform support") Cc: stable@vger.kernel.org Signed-off-by: Veerabhadrarao Badiganti Link: https://lore.kernel.org/r/1590678838-18099-1-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-pci: Fix eMMC driver strength for BYT-based controllers

2020-05-05T17:15:49+00:00

commit 1a8eb6b373c2af6533c13d1ea11f504e5010ed9a upstream. BIOS writers have begun the practice of setting 40 ohm eMMC driver strength even though the eMMC may not support it, on the assumption that the kernel will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH [offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid. This is done to avoid changing the value for different boards. Putting aside the merits of this approach, it is clear the eMMC's mask of supported driver strengths is more reliable than the value provided by BIOS. Add validation accordingly. Signed-off-by: Adrian Hunter Fixes: 51ced59cc02e ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-xenon: fix annoying 1.8V regulator warning

2020-05-05T17:15:49+00:00

commit bb32e1987bc55ce1db400faf47d85891da3c9b9f upstream. For some reason the Host Control2 register of the Xenon SDHCI controller sometimes reports the bit representing 1.8V signaling as 0 when read after it was written as 1. Subsequent read reports 1. This causes the sdhci_start_signal_voltage_switch function to report 1.8V regulator output did not become stable When CONFIG_PM is enabled, the host is suspended and resumend many times, and in each resume the switch to 1.8V is called, and so the kernel log reports this message annoyingly often. Do an empty read of the Host Control2 register in Xenon's .voltage_switch method to circumvent this. This patch fixes this particular problem on Turris MOX. Signed-off-by: Marek Behún Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V...") Cc: stable@vger.kernel.org # v4.16+ Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman

mmc: sdhci-of-at91: fix cd-gpios for SAMA5D2

2020-04-02T14:34:18+00:00

commit 53dd0a7cd65edc83b0c243d1c08377c8b876b2ee upstream. SAMA5D2x doesn't drive CMD line if GPIO is used as CD line (at least SAMA5D27 doesn't). Fix this by forcing card-detect in the module if module-controlled CD is not used. Fixed commit addresses the problem only for non-removable cards. This amends it to also cover gpio-cd case. Cc: stable@vger.kernel.org Fixes: 7a1e3f143176 ("mmc: sdhci-of-at91: force card detect value for non removable devices") Signed-off-by: Michał Mirosław Acked-by: Adrian Hunter Link: https://lore.kernel.org/r/8d10950d9940468577daef4772b82a071b204716.1584290561.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman