kernel/linux.git/drivers/media/i2c, branch v7.0.11

media: i2c: og01a1b: Fix V4L2 subdevice data initialization on probe

2026-05-23T11:08:45+00:00

[ Upstream commit 535b7f106991c7d8f0e5b8e1769bfb8b1ce9d3d6 ] It's necessary to finalize the camera sensor subdevice initialization on driver probe and clean V4L2 subdevice data up on error paths and driver removal. The change fixes a previously reported by v4l2-compliance issue of the failed VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT test: fail: v4l2-test-controls.cpp(1104): subscribe event for control 'User Controls' failed Fixes: 472377febf84 ("media: Add a driver for the og01a1b camera sensor") Signed-off-by: Vladimir Zapolskiy Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Sasha Levin

media: i2c: ov08d10: fix runtime PM handling in probe

2026-05-17T15:16:26+00:00

commit 35c7046be2be5e60be8128facb359a47f39e99cd upstream. Set the device's runtime PM status and enable runtime PM before registering the async sub-device. This is needed to avoid the case where the device is runtime PM resumed while runtime PM has not been enabled yet. Remove the related, non-driver-specific comment while at it. Fixes: 7be91e02ed57 ("media: i2c: Add ov08d10 camera sensor driver") Cc: stable@vger.kernel.org Reviewed-by: Philipp Zabel Signed-off-by: Matthias Fend Signed-off-by: Sakari Ailus Signed-off-by: Hans Verkuil Signed-off-by: Greg Kroah-Hartman

media: i2c: ov08d10: fix image vertical start setting

2026-05-17T15:16:26+00:00

commit 5d150fa0f16096d736bd24d13e04495da5116fab upstream. The current settings for the "image vertical start" register appear to be incorrect. While this only results in an incorrect start line for native modes, this faulty setting causes actual problems in binning mode. At least on an i.MX8MP test system, only corrupted frames could be received. To correct this, the recommended settings from the reference register sets are used for all modes. Since this shifts the start by one line, the Bayer pattern also changes, which has also been corrected. Fixes: 7be91e02ed57 ("media: i2c: Add ov08d10 camera sensor driver") Cc: stable@vger.kernel.org Signed-off-by: Matthias Fend Signed-off-by: Sakari Ailus Signed-off-by: Hans Verkuil Signed-off-by: Greg Kroah-Hartman

media: i2c: imx412: Assert reset GPIO during probe

2026-05-17T15:16:26+00:00

commit 8467c5ff5acae28513bc1e0af535e06b41b04344 upstream. Assert the reset GPIO before first power up. This avoids a mismatch where the first power up (when the reset GPIO defaults deasserted) differs from subsequent cycles. Signed-off-by: Wenmeng Liu Fixes: 9214e86c0cc1 ("media: i2c: Add imx412 camera sensor driver") Cc: stable@vger.kernel.org Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: i2c: imx283: Fix hang when going from large to small resolution

2026-05-17T15:16:25+00:00

commit 9206359b2c396ff594adf39bc7daaadab0fcb367 upstream. When switching between modes (e.g. full resolution to binned), standby_cancel() previously cleared XMSTA (starting master mode data output) before the new mode's MDSEL, crop, and timing registers were programmed in start_streaming(). This caused the sensor to briefly output MIPI data using the previous mode's configuration. On receivers like imx-mipi-csis, this leads to FIFO overflow errors when switching from a higher to a lower resolution, as the receiver is configured for the new smaller frame size but receives stale full-resolution data. Fix this by moving the XMSTA and SYNCDRV register writes from standby_cancel() to the end of start_streaming(), after all mode, crop, and timing registers have been configured. Also explicitly stop master mode (XMSTA=1) when stopping the stream, matching the pattern used by other Sony sensor drivers (imx290, imx415). Use named macros IMX283_XMSTA_START/STOP instead of raw 0/BIT(0) for readability. Cc: stable@vger.kernel.org Fixes: ccb4eb4496fa ("media: i2c: Add imx283 camera sensor driver") Signed-off-by: Jai Luthra Tested-by: Kieran Bingham Reviewed-by: Kieran Bingham Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: i2c: imx283: Enter full standby when stopping streaming

2026-05-17T15:16:24+00:00

commit bce1349dbf6348ddee47308e2ed08878356de317 upstream. Use IMX283_STANDBY (bit 0) instead of IMX283_STBLOGIC (bit 1) when stopping streaming. STBLOGIC only puts the sensor logic into standby but leaves the MIPI interface (along with other components) in an indeterminate state. This (presumably) causes the CSI receiver (e.g. Raspberry Pi's CFE) to miss the LP-11 to HS transition when streaming restarts, resulting in a hang of 10+ seconds. The issue is most visible when immediately restarting a full-resolution stream after stopping a 3x3 binned one, so that runtime suspend hasn't yet been triggered. Writing IMX283_STANDBY puts the entire sensor into standby. The imx283_standby_cancel() sequence already handles the full wakeup from this suspended state. Cc: stable@vger.kernel.org Link: https://github.com/raspberrypi/linux/issues/7153 Link: https://github.com/will127534/OneInchEye/issues/12 Fixes: ccb4eb4496fa ("media: i2c: Add imx283 camera sensor driver") Signed-off-by: Jai Luthra Tested-by: Kieran Bingham Reviewed-by: Kieran Bingham Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: i2c: ov5647: Fix runtime PM refcount leak in s_ctrl

2026-05-17T15:16:24+00:00

commit f11ae9c04f8368a3b5a0280ef595198dace1c983 upstream. Three control cases (AUTOGAIN, EXPOSURE_AUTO, ANALOGUE_GAIN) directly return without calling pm_runtime_put(), causing runtime PM reference count leaks. Change these cases from 'return' to 'ret = ... break' pattern to ensure pm_runtime_put() is always called before function exit. Fixes: 4f66f36388d5 ("media: i2c: ov5647: Convert to CCI register access helpers") Cc: stable@vger.kernel.org Signed-off-by: Xiaolei Wang Reviewed-by: Tarang Raval Reviewed-by: Jacopo Mondi Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: i2c: ov8856: free control handler on error in ov8856_init_controls()

2026-05-17T15:16:23+00:00

commit f75e160745663ce9b13362ae6e90bd439c58df69 upstream. The control handler wasn't freed if adding controls failed, add an error exit label and convert the existing error return to use it. Fixes: 879347f0c258 ("media: ov8856: Add support for OV8856 sensor") Cc: stable@vger.kernel.org Signed-off-by: Alexander Koskovich Signed-off-by: Sakari Ailus Signed-off-by: Hans Verkuil Signed-off-by: Greg Kroah-Hartman

media: i2c: imx219: Check return value of devm_gpiod_get_optional() in imx219_probe()

2026-05-07T04:13:48+00:00

commit 943b1f27a3eead21b22e2531a5432ea5910b60eb upstream. The devm_gpiod_get_optional() function may return an error pointer (ERR_PTR) in case of a genuine failure during GPIO acquisition, not just NULL which indicates the legitimate absence of an optional GPIO. Add an IS_ERR() check after the function call to catch such errors and propagate them to the probe function, ensuring the driver fails to load safely rather than proceeding with an invalid pointer. Fixes: 1283b3b8f82b ("media: i2c: Add driver for Sony IMX219 sensor") Cc: stable@vger.kernel.org Signed-off-by: Chen Ni Reviewed-by: Dave Stevenson Reviewed-by: Jai Luthra Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman

media: ccs: Avoid deadlock in ccs_init_state()

2026-03-26T12:14:07+00:00

The sub-device state lock has been already acquired when ccs_init_state() is called. Do not try to acquire it again. Reported-by: David Heidelberg Fixes: a88883d1209c ("media: ccs: Rely on sub-device state locking") Signed-off-by: Sakari Ailus Signed-off-by: Hans Verkuil