kernel/linux.git/drivers/irqchip/Makefile, branch v5.15.208

Merge tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2021-04-26T19:30:36+00:00

Pull ARM Apple M1 platform support from Arnd Bergmann: "The Apple M1 is the processor used it all current generation Apple Macintosh computers. Support for this platform so far is rudimentary, but it boots and can use framebuffer and serial console over a special USB cable. Support for several essential on-chip devices (USB, PCIe, IOMMU, NVMe) is work in progress but was not ready in time. A very detailed description of what works is in the commit message of commit 1bb2fd3880d4 ("Merge tag 'm1-soc-bringup-v5' [..]") and on the AsahiLinux wiki" Link: https://lore.kernel.org/linux-arm-kernel/bdb18e9f-fcd7-1e31-2224-19c0e5090706@marcan.st/ * tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: asm-generic/io.h: Unbork ioremap_np() declaration arm64: apple: Add initial Apple Mac mini (M1, 2020) devicetree dt-bindings: display: Add apple,simple-framebuffer arm64: Kconfig: Introduce CONFIG_ARCH_APPLE irqchip/apple-aic: Add support for the Apple Interrupt Controller dt-bindings: interrupt-controller: Add DT bindings for apple-aic arm64: Move ICH_ sysreg bits from arm-gic-v3.h to sysreg.h of/address: Add infrastructure to declare MMIO as non-posted asm-generic/io.h: implement pci_remap_cfgspace using ioremap_np arm64: Implement ioremap_np() to map MMIO as nGnRnE docs: driver-api: device-io: Document ioremap() variants & access funcs docs: driver-api: device-io: Document I/O access functions asm-generic/io.h: Add a non-posted variant of ioremap() arm64: arch_timer: Implement support for interrupt-names dt-bindings: timer: arm,arch_timer: Add interrupt-names support arm64: cputype: Add CPU implementor & types for the Apple M1 cores dt-bindings: arm: cpus: Add apple,firestorm & icestorm compatibles dt-bindings: arm: apple: Add bindings for Apple ARM platforms dt-bindings: vendor-prefixes: Add apple prefix

irqchip: Add support for IDT 79rc3243x interrupt controller

2021-04-22T15:03:18+00:00

IDT 79rc3243x SoCs have rather simple interrupt controllers connected to the MIPS CPU interrupt lines. Each of them has room for up to 32 interrupts. Signed-off-by: Thomas Bogendoerfer Signed-off-by: Marc Zyngier Link: https://lore.kernel.org/r/20210422145330.73452-1-tsbogend@alpha.franken.de

irqchip/apple-aic: Add support for the Apple Interrupt Controller

2021-04-08T11:18:41+00:00

This is the root interrupt controller used on Apple ARM SoCs such as the M1. This irqchip driver performs multiple functions: * Handles both IRQs and FIQs * Drives the AIC peripheral itself (which handles IRQs) * Dispatches FIQs to downstream hard-wired clients (currently the ARM timer). * Implements a virtual IPI multiplexer to funnel multiple Linux IPIs into a single hardware IPI Reviewed-by: Marc Zyngier Acked-by: Will Deacon Signed-off-by: Hector Martin

irqchip: Add driver for WPCM450 interrupt controller

2021-04-07T12:26:00+00:00

The WPCM450 AIC ("Advanced Interrupt Controller") is the interrupt controller found in the Nuvoton WPCM450 SoC and other Winbond/Nuvoton SoCs. The list of registers if based on the AMI vendor kernel and the Nuvoton W90N745 datasheet. Although the hardware supports other interrupt modes, the driver only supports high-level interrupts at the moment, because other modes could not be tested so far. Signed-off-by: Jonathan Neuschäfer Signed-off-by: Marc Zyngier Link: https://lore.kernel.org/r/20210406120921.2484986-7-j.neuschaefer@gmx.net

irqchip: Add support for Realtek RTL838x/RTL839x interrupt controller

2021-02-04T10:36:15+00:00

This is a standard IRQ driver with only status and mask registers. The mapping from SoC interrupts (18-31) to MIPS core interrupts is done via an interrupt-map in device tree. Signed-off-by: Bert Vermeulen Signed-off-by: Birger Koblitz Acked-by: John Crispin Signed-off-by: Marc Zyngier Link: https://lore.kernel.org/r/20210122204224.509124-3-bert@biot.com

irqchip/sun6i-r: Use a stacked irqchip driver

2021-01-21T20:21:49+00:00

The R_INTC in the A31 and newer sun8i/sun50i SoCs is more similar to the original sun4i interrupt controller than the sun7i/sun9i NMI controller. It is used for two distinct purposes: - To control the trigger, latch, and mask for the NMI input pin - To provide the interrupt input for the ARISC coprocessor As this interrupt controller is not documented, information about it comes from vendor-provided firmware blobs and from experimentation. Differences from the sun4i interrupt controller appear to be: - It only has one or two registers of each kind (max 32 or 64 IRQs) - Multiplexing logic is added to support additional inputs - There is no FIQ-related logic - There is no interrupt priority logic In order to fulfill its two purposes, this hardware block combines four types of IRQs. First, the NMI pin is routed to the "IRQ 0" input on this chip, with a trigger type controlled by the NMI_CTRL_REG. The "IRQ 0 pending" output from this chip, if enabled, is then routed to a SPI IRQ input on the GIC. In other words, bit 0 of IRQ_ENABLE_REG *does* affect the NMI IRQ seen at the GIC. The NMI is followed by a contiguous block of 15 "direct" (my name for them) IRQ inputs that are connected in parallel to both R_INTC and the GIC. Or in other words, these bits of IRQ_ENABLE_REG *do not* affect the IRQs seen at the GIC. Following the direct IRQs are the ARISC's copy of banked IRQs for shared peripherals. These are not relevant to Linux. The remaining IRQs are connected to a multiplexer and provide access to the first (up to) 128 SPIs from the ARISC. This range of SPIs overlaps with the direct IRQs. Because of the 1:1 correspondence between R_INTC and GIC inputs, this is a perfect scenario for using a stacked irqchip driver. We want to hook into setting the NMI trigger type, but not actually handle any IRQ here. To allow access to all multiplexed IRQs, this driver requires a new binding where the interrupt number matches the GIC interrupt number. (This moves the NMI from number 0 to 32 or 96, depending on the SoC.) For simplicity, copy the three-cell GIC binding; this disambiguates interrupt 0 in the old binding (the NMI) from interrupt 0 in the new binding (SPI 0) by the number of cells. Since R_INTC is in the always-on power domain, and its output is visible to the power management coprocessor, a stacked irqchip driver provides a simple way to add wakeup support to any of its IRQs. That is the next patch; for now, just the NMI is moved over. This commit mostly reverts commit 173bda53b340 ("irqchip/sunxi-nmi: Support sun6i-a31-r-intc compatible"). Acked-by: Maxime Ripard Signed-off-by: Samuel Holland Signed-off-by: Marc Zyngier Link: https://lore.kernel.org/r/20210118055040.21910-4-samuel@sholland.org

irqchip: Remove sirfsoc driver

2021-01-21T20:21:41+00:00

The CSR SiRF prima2/atlas platforms are getting removed, so this driver is no longer needed. Cc: Barry Song Signed-off-by: Arnd Bergmann Acked-by: Barry Song Signed-off-by: Marc Zyngier Link: https://lore.kernel.org/r/20210120133008.2421897-3-arnd@kernel.org

irqchip: Remove sigma tango driver

2021-01-21T20:21:23+00:00

The tango platform is getting removed, so the driver is no longer needed. Cc: Marc Gonzalez Cc: Mans Rullgard Signed-off-by: Arnd Bergmann Acked-by: Mans Rullgard Signed-off-by: Marc Zyngier Link: https://lore.kernel.org/r/20210120133008.2421897-2-arnd@kernel.org

drivers/irqchip: Remove EZChip NPS interrupt controller

2020-12-11T14:47:50+00:00

NPS platform has been removed from ARC port and there are no in-tree users of it now. So RIP ! Signed-off-by: Vineet Gupta Signed-off-by: Marc Zyngier Cc: Thomas Gleixner Cc: Jason Cooper Cc: Marc Zyngier Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20201105212210.1891598-3-vgupta@synopsys.com

Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2020-10-24T17:33:08+00:00

Pull ARM SoC platform updates from Olof Johansson: "SoC changes, a substantial part of this is cleanup of some of the older platforms that used to have a bunch of board files. In particular: - Remove non-DT i.MX platforms that haven't seen activity in years, it's time to remove them. - A bunch of cleanup and removal of platform data for TI/OMAP platforms, moving over to genpd for power/reset control (yay!) - Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them closer to multiplatform support (not quite there yet, but getting close). There are a few other changes too, smaller fixlets, etc. For new platform support, the primary ones are: - New SoC: Hisilicon SD5203, ARM926EJ-S platform. - Cpufreq support for i.MX7ULP" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits) ARM: mstar: Select MStar intc ARM: stm32: Replace HTTP links with HTTPS ones ARM: debug: add UART early console support for SD5203 ARM: hisi: add support for SD5203 SoC ARM: omap3: enable off mode automatically clk: imx: imx35: Remove mx35_clocks_init() clk: imx: imx31: Remove mx31_clocks_init() clk: imx: imx27: Remove mx27_clocks_init() ARM: imx: Remove unused definitions ARM: imx35: Retrieve the IIM base address from devicetree ARM: imx3: Retrieve the AVIC base address from devicetree ARM: imx3: Retrieve the CCM base address from devicetree ARM: imx31: Retrieve the IIM base address from devicetree ARM: imx27: Retrieve the CCM base address from devicetree ARM: imx27: Retrieve the SYSCTRL base address from devicetree ARM: s3c64xx: bring back notes from removed debug-macro.S ARM: s3c24xx: fix Wunused-variable warning on !MMU ARM: samsung: fix PM debug build with DEBUG_LL but !MMU MAINTAINERS: mark linux-samsung-soc list non-moderated ARM: imx: Remove remnant board file support pieces ...